I ALWAYS remove Exits On Suspend. As part of my little
every-new-release-of-LiveCode thing, there's that, there's whatever FIXes
I've submitted that aren't kid-tested/mother-approved, yet, etc. Now if we
could get push working better so I could make syncing happen in the
background...
On Wed, May 27, 2015 at 8:36 AM, Alex Shaw <a...@harryscollar.com> wrote:
> Hmm. I've just tried the following function by Ralph DiMola and no luck.
>
> function GetGpsCords
>
> local tGPS
>
> if not mobileSensorAvailable("location") then return empty
> put mobileSensorReading("location", true) into tGPS
> if tGPS["latitude"] is not empty and tGPS["longitude"] <> 0 then
> wait .25 seconds
> put mobileSensorReading("location", true) into tGPS
> end if
> if tGPS["latitude"] is not empty and tGPS["longitude"] <> 0 then
> return tGPS
> else
> answer "GPS is not enabled or your GPS can't determine your
> location." & cr & "If your GPS was just enabled, please try again in a few
> minutes." with "OK" titled "Proximity Search"
> return empty
> end if
>
> end GetGpsCords
>
> On iOS for the LC standalone settings I have ticked Location Services, GPS
> & WiFi in the Requirements and Restrictions section and
> mobileLocationAuthorizationStatus() returns 'notDetermined' on the test
> iPhone 5. The test app doesn't appear under the listed apps in Settings ->
> Privacy -> Location Services, so how this work?
>
> On the Android test device, Location is enabled under settings and I have
> Fine and Coarse Location enabled in the LC standalone settings.
>
> Using LC 7.0.5 with a iPhone 5 and Nexus 7. All up to date.
>
> regards
> alex
>
>
> On 27/05/2015 10:05 pm, Magicgate Software - Skip Kimpel wrote:
>
>> My first stumbling block with it was that I didn't realize the data was
>> returned in an array. Once I saw that I was able to easily parse the data
>> and begin using it.
>>
>> SKIP
>>
>> On Wed, May 27, 2015 at 7:50 AM, Alex Shaw <a...@harryscollar.com> wrote:
>>
>> Hi
>>>
>>> I recently tested mobileCurrentLocation() for both Android & iOS on LC
>>> 7.0.5 and can't seem to get it working.
>>>
>>> Is there a good guide somewhere?
>>>
>>> The dictionary is definitely lacking in this area.
>>>
>>> regards
>>> alex
>>>
>>> On 21/05/2015 10:36 am, Richard Gaskin wrote:
>>>
>>> Roger Eller wrote:
>>>>
>>>> That's what I find most frustrating about reading this list. We have
>>>>> an x-plat dev environment, so I keep hoping to see mergExt eventually
>>>>> go x-plat too. After all, there's a lot of android devices out there
>>>>> these days.
>>>>>
>>>> Last time I used it mobileCurrentLocation is working on Android.
>>>>
>>>> Does it not work in iOS?
>>>>
>>>>
>>>> _______________________________________________
>>> use-livecode mailing list
>>> use-livecode@lists.runrev.com
>>> Please visit this url to subscribe, unsubscribe and manage your
>>> subscription preferences:
>>> http://lists.runrev.com/mailman/listinfo/use-livecode
>>>
>>> _______________________________________________
>> use-livecode mailing list
>> use-livecode@lists.runrev.com
>> Please visit this url to subscribe, unsubscribe and manage your
>> subscription preferences:
>> http://lists.runrev.com/mailman/listinfo/use-livecode
>>
>>
>
> _______________________________________________
> use-livecode mailing list
> use-livecode@lists.runrev.com
> Please visit this url to subscribe, unsubscribe and manage your
> subscription preferences:
> http://lists.runrev.com/mailman/listinfo/use-livecode
>
--
On the first day, God created the heavens and the Earth
On the second day, God created the oceans.
On the third day, God put the animals on hold for a few hours,
and did a little diving.
And God said, "This is good."
_______________________________________________
use-livecode mailing list
use-livecode@lists.runrev.com
Please visit this url to subscribe, unsubscribe and manage your subscription
preferences:
http://lists.runrev.com/mailman/listinfo/use-livecode
