As it turns out, the problem was caused by "explicitVariables"; something I ran into when I first started working on this project again after a very long layoff. Frankly, I don't remember how to call variables "explicitly". I'm accustomed to just creating them by putting something into the variable when I need one. I've always done it that way, but something seems to have changed with LC recently. I don't have it set to true. In fact I started setting it to false when I found I was having a problem. Suggestions anyone?
TIA, Joe Wilkins On Nov 19, 2012, at 10:10 PM, Joe Lewis Wilkins wrote: > Sorry, I just never think of it as "compiling", and it was throwing a number > of errors. I just couldn't see them until I magnify everything. It's tough > when you can't see. I'm sure you've put me on the track. Thanks. > > Joe Wilkins > > On Nov 19, 2012, at 10:00 PM, Joe Lewis Wilkins wrote: > >> Thanks fellas. Sounds promising. Right now I'm trying to figure out how to >> compile a stack other than by building a standalone. Is there a simple way >> to compile a single stack? >> >> TIA, >> >> Joe Wilkins >> >> On Nov 19, 2012, at 9:49 PM, Scott Rossi wrote: >> >>> This is a long shot, but I've had a situation occur several times where >>> the script editor compiles and closes with a *technically* invalid script. >>> The reason I say "technically" is that the script has a minor error that >>> should cause the editor to throw an error, but instead it accepts the >>> script, and one of the symptoms of this is the handlers don't show up in >>> the handler list. It's only happened a few times, and I can't say if this >>> is what's happening in your case. But try looking for some script lines >>> that aren't indented properly as (I believe) this is how I tracked down >>> the problem in my case. >>> >>> Regards, >>> >>> Scott Rossi >>> Creative Director >>> Tactile Media, UX Design >>> >>> >>> >>> >>> On 11/19/12 9:33 PM, "Joe Lewis Wilkins" <pepe...@cox.net> wrote: >>> >>>> Hi LCers: >>>> >>>> I just opened one of several stacks in a project I've been working on for >>>> quite some time under LC 4.5.2, and I find that the Handlers in the Stack >>>> Script are not showing. The script and all of its handlers are there, but >>>> they are not listed in the menus Handler item or showing in the left >>>> column of the script. There are several stacks in the project and all of >>>> the others are fine. With my stupidly poor vision I sometimes click on >>>> something in error. Any idea what I may have done to cause this, or what >>>> I can do to restore the handlers to the Menu item? Even though the >>>> Handlers are in the stack script, they do not work when called. The stack >>>> also has some card scripts. Their handlers ARE listed and do work. >>>> >>>> TIA, >>>> >>>> Joe Wilkins >>>> >>>> On Nov 19, 2012, at 8:50 PM, J. Landman Gay wrote: >>>> >>>>> Is there a way to position an iPad/iOS popover? >>>>> >>>>> -- >>>>> Jacqueline Landman Gay | jac...@hyperactivesw.com >>>>> HyperActive Software | http://www.hyperactivesw.com >>>>> >>>>> _______________________________________________ >>>>> use-livecode mailing list >>>>> use-livecode@lists.runrev.com >>>>> Please visit this url to subscribe, unsubscribe and manage your >>>>> subscription preferences: >>>>> http://lists.runrev.com/mailman/listinfo/use-livecode >>>> >>>> >>>> _______________________________________________ >>>> use-livecode mailing list >>>> use-livecode@lists.runrev.com >>>> Please visit this url to subscribe, unsubscribe and manage your >>>> subscription preferences: >>>> http://lists.runrev.com/mailman/listinfo/use-livecode >>>> >>> >>> >>> >>> _______________________________________________ >>> use-livecode mailing list >>> use-livecode@lists.runrev.com >>> Please visit this url to subscribe, unsubscribe and manage your >>> subscription preferences: >>> http://lists.runrev.com/mailman/listinfo/use-livecode >> >> >> _______________________________________________ >> use-livecode mailing list >> use-livecode@lists.runrev.com >> Please visit this url to subscribe, unsubscribe and manage your subscription >> preferences: >> http://lists.runrev.com/mailman/listinfo/use-livecode > > > _______________________________________________ > use-livecode mailing list > use-livecode@lists.runrev.com > Please visit this url to subscribe, unsubscribe and manage your subscription > preferences: > http://lists.runrev.com/mailman/listinfo/use-livecode _______________________________________________ use-livecode mailing list use-livecode@lists.runrev.com Please visit this url to subscribe, unsubscribe and manage your subscription preferences: http://lists.runrev.com/mailman/listinfo/use-livecode
