Что-то я не увидел сообщений о подгружаемом firmware
18 марта 2011 г. 12:38 пользователь Shinto Volokos <a.volo...@gmail.com>написал: > Сделал, ничего интересного: > [74284.016870] rtl8187: wireless radio switch turned off > [74289.008912] rtl8187: wireless radio switch turned on > [74292.973972] ADDRCONF(NETDEV_UP): wlan0: link is not ready > [74305.493828] wlan0: authenticate with 00:1c:f0:0e:fb:b7 (try 1) > [74305.550602] wlan0: authenticated > [74305.617330] wlan0: associate with 00:1c:f0:0e:fb:b7 (try 1) > [74305.684088] usb 5-1: USB disconnect, address 4 > [74305.691077] wlan0: RX AssocResp from 00:1c:f0:0e:fb:b7 (capab=0x411 > status=0 aid=1) > [74305.691082] wlan0: associated > [74305.765634] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready > [74316.272032] wlan0: no IPv6 routers present > [74547.778643] usbcore: deregistering interface driver rtl8187 > [74547.857369] wlan0: deauthenticating from 00:1c:f0:0e:fb:b7 by local > choice (reason=3) > [74548.017133] cfg80211: All devices are disconnected, going to restore > regulatory settings > [74548.017140] cfg80211: Restoring regulatory settings > [74548.017145] cfg80211: Calling CRDA to update world regulatory domain > [74548.136078] usb 1-2: reset high speed USB device using ehci_hcd and > address 2 > [74548.489750] cfg80211: World regulatory domain updated: > [74548.489756] (start_freq - end_freq @ bandwidth), > (max_antenna_gain, max_eirp) > [74548.489761] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [74548.489766] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, > 2000 mBm) > [74548.489770] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, > 2000 mBm) > [74548.489774] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [74548.489778] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [74559.018205] phy6: Selected rate control algorithm 'minstrel' > [74559.020715] phy6: hwaddr 00:16:44:6e:6e:0f, RTL8187BvE V0 + > rtl8225z2, rfkill mask 2 > [74559.062414] rtl8187: Customer ID is 0x00 > [74559.062483] Registered led device: rtl8187-phy6::radio > [74559.062515] Registered led device: rtl8187-phy6::tx > [74559.062547] Registered led device: rtl8187-phy6::rx > [74559.064410] rtl8187: wireless switch is on > [74559.064467] usbcore: registered new interface driver rtl8187 > [74559.136199] phy6: eeprom reset timeout! > [74563.089668] ADDRCONF(NETDEV_UP): wlan0: link is not ready > [74568.637326] wlan0: authenticate with 00:1c:f0:0e:fb:b7 (try 1) > [74568.644176] wlan0: authenticated > [74568.644219] wlan0: associate with 00:1c:f0:0e:fb:b7 (try 1) > [74568.647660] wlan0: RX AssocResp from 00:1c:f0:0e:fb:b7 (capab=0x411 > status=0 aid=1) > [74568.647667] wlan0: associated > [74568.721808] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready > [74579.328035] wlan0: no IPv6 routers present > > В Чт., 17/03/2011 в 20:46 +0300, Oleg A. Anisimov пишет: > > Выгрузите модуль, загрузите снова и взгляните в вывод dmesg. > > > > > -- > ubuntu-ru mailing list > ubuntu-ru@lists.ubuntu.com > https://lists.ubuntu.com/mailman/listinfo/ubuntu-ru > -- -- С наилучшими пожеланиями, Олег Анисимов AKA Yoda
-- ubuntu-ru mailing list ubuntu-ru@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-ru
