Public bug reported:
Binary package hint: pulseaudio
sound worked great in 7.10 but after 8.04 upgrade it don't work.
"no volume control gsstreamer plugins and/or devices found"
lspci -v
"80:01.0 Audio device: VIA Technologies, Inc. VIA High Definition Audio
Controller (rev 10)
Subsystem: Giga-byte Technology Unknown device a002
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at bfffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>"
this is a via pc3500 motherboard.
sold at wallmart in everex desktop.
:~$ dmesg
[ 0.000000] Linux version 2.6.24-12-386 ([EMAIL PROTECTED]) (gcc version
4.2.3 (Ubuntu 4.2.3-2ubuntu4)) #1 Wed Mar 12 22:30:29 UTC 2008 (Ubuntu
2.6.24-12.22-386)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
[ 0.000000] BIOS-e820: 000000003fee0000 - 000000003fee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fee3000 - 000000003fef0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003fef0000 - 000000003ff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 126MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f3b70
[ 0.000000] Entering add_active_range(0, 0, 261856) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 261856
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 261856
[ 0.000000] On node 0 totalpages: 261856
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 253 pages used for memmap
[ 0.000000] HighMem zone: 32227 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F7CE0 checksum 0
[ 0.000000] ACPI: RSDP 000F7CE0, 0014 (r0 FICINC)
[ 0.000000] ACPI: RSDT 3FEE3040, 0038 (r1 FICINC FIRST MB 42302E31 AWRD
0)
[ 0.000000] ACPI: FACP 3FEE30C0, 0074 (r1 FICINC FIRST MB 42302E31 AWRD
0)
[ 0.000000] ACPI: DSDT 3FEE3180, 651D (r1 FICINC AWRDACPI 1000 MSFT
3000000)
[ 0.000000] ACPI: FACS 3FEE0000, 0040
[ 0.000000] ACPI: SLIC 3FEE97C0, 0176 (r1 FICINC FIRST MB 42302E31 AWRD
1010101)
[ 0.000000] ACPI: HPET 3FEE9980, 0038 (r1 FICINC FIRST MB 42302E31 AWRD
98)
[ 0.000000] ACPI: MCFG 3FEE9A00, 003C (r1 FICINC FIRST MB 42302E31 AWRD
0)
[ 0.000000] ACPI: APIC 3FEE9700, 0066 (r1 FICINC FIRST MB 42302E31 AWRD
0)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:10 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfecc0000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 3, version 3, address 0xfecc0000, GSI 24-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 2 I/O APICs
[ 0.000000] ACPI: HPET id: 0x11068201 base: 0xfe800000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 40000000 (gap:
3ff00000:a0100000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 -
00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 -
00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 -
0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 259811
[ 0.000000] Kernel command line:
root=UUID=ede485a5-2ab0-4401-82a1-3e1c610820f6 ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] mapped IOAPIC to ffff9000 (fecc0000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1499.984 MHz processor.
[ 17.117108] Console: colour VGA+ 80x25
[ 17.117114] console [tty0] enabled
[ 17.117864] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 17.119046] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 17.188991] Memory: 1026948k/1047424k available (2075k kernel code, 19756k
reserved, 969k data, 356k init, 129920k highmem)
[ 17.189012] virtual kernel memory layout:
[ 17.189014] fixmap : 0xfffa6000 - 0xfffff000 ( 356 kB)
[ 17.189017] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 17.189021] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 17.189024] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 17.189027] .init : 0xc03fc000 - 0xc0455000 ( 356 kB)
[ 17.189030] .data : 0xc0306c1d - 0xc03f93a4 ( 969 kB)
[ 17.189033] .text : 0xc0100000 - 0xc0306c1d (2075 kB)
[ 17.189041] Checking if this processor honours the WP bit even in supervisor
mode... Ok.
[ 17.189136] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1,
Nodes=1
[ 17.189319] hpet clockevent registered
[ 17.269242] Calibrating delay using timer specific routine.. 3002.26
BogoMIPS (lpj=6004529)
[ 17.269281] Security Framework initialized
[ 17.269294] SELinux: Disabled at boot.
[ 17.269325] AppArmor: AppArmor initialized
[ 17.269335] Failure registering capabilities with primary security module.
[ 17.269346] Mount-cache hash table entries: 512
[ 17.269528] CPU: After generic identify, caps: a7c9bbff 00100000 00000000
00000000 00000001 00000000 00000000 00000000
[ 17.269545] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 17.269552] CPU: L2 Cache: 128K (64 bytes/line)
[ 17.269556] CPU: After all inits, caps: 27c9bbff 00100000 00000000 00000000
00000001 00003fcc 00000000 00000000
[ 17.269573] Compat vDSO mapped to ffffe000.
[ 17.269595] CPU: Centaur VIA Esther processor 1500MHz stepping 09
[ 17.269605] Checking 'hlt' instruction... OK.
[ 17.287532] Freeing SMP alternatives: 0k freed
[ 17.287759] Early unpacking initramfs... done
[ 18.020097] ACPI: Core revision 20070126
[ 18.020241] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not
found.
[ 18.027455] ENABLING IO-APIC IRQs
[ 18.027662] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 18.172570] net_namespace: 64 bytes
[ 18.172586] Booting paravirtualized kernel on bare hardware
[ 18.173463] Time: 5:25:59 Date: 03/30/08
[ 18.173551] NET: Registered protocol family 16
[ 18.173833] EISA bus registered
[ 18.173843] ACPI: bus type pci registered
[ 18.183063] PCI: PCI BIOS revision 3.00 entry at 0xf9950, last bus=128
[ 18.183069] PCI: Using configuration type 1
[ 18.183073] Setting up standard PCI resources
[ 18.188120] ACPI: EC: Look up EC in DSDT
[ 18.203041] ACPI: Interpreter enabled
[ 18.203051] ACPI: (supports S0 S3 S4 S5)
[ 18.203076] ACPI: Using IOAPIC for interrupt routing
[ 18.218891] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 18.221027] PCI: Transparent bridge - 0000:00:13.1
[ 18.221083] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 18.221565] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXG._PRT]
[ 18.221815] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 18.222064] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PB._PRT]
[ 18.345899] ACPI: PCI Root Bridge [PCI1] (0000:80)
[ 18.346110] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
[ 18.347188] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
[ 18.347551] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
[ 18.347913] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
[ 18.348290] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12)
[ 18.348615] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0,
disabled.
[ 18.348929] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0,
disabled.
[ 18.349243] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0,
disabled.
[ 18.349576] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *5
[ 18.349852] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 18.349901] pnp: PnP ACPI init
[ 18.349920] ACPI: bus type pnp registered
[ 18.359890] pnp: PnP ACPI: found 17 devices
[ 18.359898] ACPI: ACPI bus type pnp unregistered
[ 18.359906] PnPBIOS: Disabled by ACPI PNP
[ 18.360292] PCI: Using ACPI for IRQ routing
[ 18.360299] PCI: If a device doesn't work, try "pci=routeirq". If it helps,
post a report
[ 19.578925] NET: Registered protocol family 8
[ 19.578930] NET: Registered protocol family 20
[ 19.578985] hpet0: at MMIO 0xfe800000, IRQs 2, 8, 0
[ 19.578993] hpet0: 3 32-bit timers, 14318180 Hz
[ 19.580073] AppArmor: AppArmor Filesystem Enabled
[ 19.582912] Time: tsc clocksource has been installed.
[ 19.582927] Switched to high resolution mode on CPU 0
[ 19.590911] system 00:01: ioport range 0x400-0x47f has been reserved
[ 19.590917] system 00:01: ioport range 0x500-0x50f has been reserved
[ 19.590937] system 00:02: iomem range 0xf0001000-0xf0001fff has been reserved
[ 19.590956] system 00:03: iomem range 0xf0002000-0xf0002fff has been reserved
[ 19.590970] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[ 19.590976] system 00:04: ioport range 0x290-0x29f has been reserved
[ 19.590982] system 00:04: ioport range 0x800-0x805 has been reserved
[ 19.590989] system 00:04: ioport range 0x820-0x827 has been reserved
[ 19.591015] system 00:0d: iomem range 0xf0000000-0xf0000fff has been reserved
[ 19.591030] system 00:0e: iomem range 0xe0000000-0xefffffff could not be
reserved
[ 19.591046] system 00:10: iomem range 0xf0000-0xfffff could not be reserved
[ 19.591053] system 00:10: iomem range 0xfe800000-0xfe8000ff has been reserved
[ 19.591060] system 00:10: iomem range 0x3fee0000-0x3fefffff could not be
reserved
[ 19.591068] system 00:10: iomem range 0xffff0000-0xffffffff could not be
reserved
[ 19.591075] system 00:10: iomem range 0x0-0x9ffff could not be reserved
[ 19.591082] system 00:10: iomem range 0x100000-0x3fedffff could not be
reserved
[ 19.591089] system 00:10: iomem range 0xfec00000-0xfec00fff could not be
reserved
[ 19.591096] system 00:10: iomem range 0xfee00000-0xfee00fff could not be
reserved
[ 19.591103] system 00:10: iomem range 0xfff80000-0xfffeffff has been reserved
[ 19.621722] PCI: Bridge: 0000:00:01.0
[ 19.621729] IO window: b000-bfff
[ 19.621738] MEM window: dfb00000-dfbfffff
[ 19.621745] PREFETCH window: dfe00000-dfefffff
[ 19.621758] PCI: Bridge: 0000:00:02.0
[ 19.621763] IO window: a000-afff
[ 19.621770] MEM window: dc000000-deffffff
[ 19.621777] PREFETCH window: c0000000-cfffffff
[ 19.621785] PCI: Bridge: 0000:00:03.0
[ 19.621790] IO window: c000-cfff
[ 19.621799] MEM window: dfd00000-dfdfffff
[ 19.621806] PREFETCH window: dfc00000-dfcfffff
[ 19.621817] PCI: Bridge: 0000:00:13.1
[ 19.621822] IO window: 9000-9fff
[ 19.621829] MEM window: dfa00000-dfafffff
[ 19.621836] PREFETCH window: df900000-df9fffff
[ 19.621862] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 19.621903] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) ->
IRQ 16
[ 19.621913] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 19.621938] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) ->
IRQ 17
[ 19.621948] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 19.621967] PCI: Setting latency timer of device 0000:00:13.1 to 64
[ 19.621995] NET: Registered protocol family 2
[ 19.658879] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 19.659441] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[ 19.661133] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 19.661638] TCP: Hash tables configured (established 131072 bind 65536)
[ 19.661646] TCP reno registered
[ 19.671006] checking if image is initramfs... it is
[ 21.103619] Freeing initrd memory: 6937k freed
[ 21.104410] audit: initializing netlink socket (disabled)
[ 21.104432] audit(1206854760.708:1): initialized
[ 21.104739] highmem bounce pool size: 64 pages
[ 21.107595] VFS: Disk quotas dquot_6.5.1
[ 21.107647] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 21.107881] io scheduler noop registered
[ 21.107886] io scheduler anticipatory registered
[ 21.107890] io scheduler deadline registered
[ 21.107913] io scheduler cfq registered (default)
[ 21.107943] PCI: VIA PCI bridge detected. Disabling DAC.
[ 21.108044] Boot video device is 0000:02:00.0
[ 21.108249] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 21.108303] assign_interrupt_mode Found MSI capability
[ 21.108366] Allocate Port Service[0000:00:02.0:pcie00]
[ 21.108424] Allocate Port Service[0000:00:02.0:pcie02]
[ 21.108540] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 21.108600] assign_interrupt_mode Found MSI capability
[ 21.108664] Allocate Port Service[0000:00:03.0:pcie00]
[ 21.108717] Allocate Port Service[0000:00:03.0:pcie02]
[ 21.109054] isapnp: Scanning for PnP cards...
[ 21.463121] isapnp: No Plug & Play device found
[ 21.509584] hpet_resources: 0xfe800000 is busy
[ 21.509622] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 21.509809] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 21.510123] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 21.511089] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 21.511717] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 21.513113] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 21.513248] input: Macintosh mouse button emulation as
/devices/virtual/input/input0
[ 21.513465] PNP: No PS/2 controller found. Probing ports directly.
[ 21.513881] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 21.513889] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 21.524942] mice: PS/2 mouse device common for all mice
[ 21.525127] EISA: Probing bus 0 at eisa.0
[ 21.525182] EISA: Detected 0 cards.
[ 21.525188] cpuidle: using governor ladder
[ 21.525467] NET: Registered protocol family 1
[ 21.525526] Using IPI Shortcut mode
[ 21.525580] registered taskstats version 1
[ 21.525841] Magic number: 0:139:417
[ 21.526201] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 21.526206] EDD information not available.
[ 21.526721] Freeing unused kernel memory: 356k freed
[ 23.107083] fuse init (API version 7.9)
[ 23.148350] ACPI: Fan [FAN] (on)
[ 23.163407] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 23.163419] ACPI: Processor [CPU0] (supports 2 throttling states)
[ 23.166491] ACPI: Thermal Zone [THRM] (37 C)
[ 25.128508] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 25.128520] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 25.129919] VP_IDE: IDE controller (0x1106:0x0571 rev 0x07) at PCI slot
0000:00:0f.1
[ 25.129970] VP_IDE: not 100% native mode: will probe irqs later
[ 25.129986] VP_IDE: VIA vt8237a (rev 00) IDE UDMA133 controller on
pci0000:00:0f.1
[ 25.130001] ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:DMA,
hdb:pio
[ 25.130018] ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:pio,
hdd:pio
[ 25.130033] Probing IDE interface ide0...
[ 25.151581] SCSI subsystem initialized
[ 25.226412] usbcore: registered new interface driver usbfs
[ 25.226452] usbcore: registered new interface driver hub
[ 25.253324] usbcore: registered new device driver usb
[ 25.267397] USB Universal Host Controller Interface driver v3.0
[ 25.326666] libata version 3.00 loaded.
[ 25.748528] hdb: IRQ probe failed (0xffffedfc)
[ 25.756338] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 25.756349] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 26.046000] hdb: IRQ probe failed (0xffffedfc)
[ 26.955333] hda: ATAPI DVD C DH52C1P, ATAPI CD/DVD-ROM drive
[ 26.955393] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 26.955734] hda: UDMA/44 mode selected
[ 26.956051] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 26.965370] Probing IDE interface ide1...
[ 27.534707] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) ->
IRQ 18
[ 27.534732] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 27.535579] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus
number 1
[ 27.535624] uhci_hcd 0000:00:10.0: irq 18, io base 0x0000e000
[ 27.535873] usb usb1: configuration #1 chosen from 1 choice
[ 27.535914] hub 1-0:1.0: USB hub found
[ 27.535924] hub 1-0:1.0: 2 ports detected
[ 27.638659] ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 22 (level, low) ->
IRQ 19
[ 27.638683] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 27.638727] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus
number 2
[ 27.638764] uhci_hcd 0000:00:10.1: irq 19, io base 0x0000dc00
[ 27.638954] usb usb2: configuration #1 chosen from 1 choice
[ 27.638994] hub 2-0:1.0: USB hub found
[ 27.639004] hub 2-0:1.0: 2 ports detected
[ 27.742544] ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) ->
IRQ 20
[ 27.742568] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 27.742609] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus
number 3
[ 27.742646] uhci_hcd 0000:00:10.2: irq 20, io base 0x0000d800
[ 27.742834] usb usb3: configuration #1 chosen from 1 choice
[ 27.742874] hub 3-0:1.0: USB hub found
[ 27.742884] hub 3-0:1.0: 2 ports detected
[ 27.846438] ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) ->
IRQ 21
[ 27.846461] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 27.846502] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus
number 4
[ 27.846539] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000d400
[ 27.846730] usb usb4: configuration #1 chosen from 1 choice
[ 27.846793] hub 4-0:1.0: USB hub found
[ 27.846802] hub 4-0:1.0: 2 ports detected
[ 27.951006] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) ->
IRQ 20
[ 27.951102] ACPI: PCI interrupt for device 0000:00:0f.0 disabled
[ 27.958200] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) ->
IRQ 20
[ 27.958226] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 27.958294] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus
number 5
[ 27.958359] ehci_hcd 0000:00:10.4: irq 20, io mem 0xdffff000
[ 27.971672] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
[ 27.971911] usb usb5: configuration #1 chosen from 1 choice
[ 27.971955] hub 5-0:1.0: USB hub found
[ 27.971966] hub 5-0:1.0: 8 ports detected
[ 28.074419] ACPI: PCI Interrupt 0000:04:0e.0[A] -> GSI 18 (level, low) ->
IRQ 22
[ 28.080095] eth0: VIA Rhine III at 0xdfafe000, 00:1a:4d:1c:6b:69, IRQ 22.
[ 28.080809] eth0: MII PHY found at address 1, status 0x786d advertising 05e1
Link 45e1.
[ 28.081016] ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 17 (level, low) ->
IRQ 23
[ 28.131825] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[23]
MMIO=[dfaff000-dfaff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 28.237466] sata_via 0000:00:0f.0: version 2.3
[ 28.237495] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) ->
IRQ 20
[ 28.237571] sata_via 0000:00:0f.0: routed to hard irq line 11
[ 28.240435] scsi0 : sata_via
[ 28.249816] scsi1 : sata_via
[ 28.252292] ata1: SATA max UDMA/133 cmd 0xfc00 ctl 0xf800 bmdma 0xec00 irq 20
[ 28.252299] ata2: SATA max UDMA/133 cmd 0xf400 ctl 0xf000 bmdma 0xec08 irq 20
[ 28.296401] hda: ATAPI 52X DVD-ROM CD-R/RW drive, 1536kB Cache
[ 28.296416] Uniform CD-ROM driver Revision: 3.20
[ 28.453594] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 28.665373] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 28.829558] ata2.00: ATA-7: WDC WD800BD-22MRA1, 10.01E01, max UDMA/133
[ 28.829568] ata2.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 28.837549] ata2.00: configured for UDMA/133
[ 28.837755] scsi 1:0:0:0: Direct-Access ATA WDC WD800BD-22MR 10.0
PQ: 0 ANSI: 5
[ 28.854893] Driver 'sd' needs updating - please use bus_type methods
[ 28.856453] sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 28.856477] sd 1:0:0:0: [sda] Write Protect is off
[ 28.856483] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 28.856507] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 28.856604] sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 28.856618] sd 1:0:0:0: [sda] Write Protect is off
[ 28.856623] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 28.856644] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 28.856653] sda: sda1 sda2 < sda5 >
[ 28.894647] sd 1:0:0:0: [sda] Attached SCSI disk
[ 28.904829] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 29.177503] Attempting manual resume
[ 29.177511] swsusp: Resume From Partition 8:5
[ 29.177515] PM: Checking swsusp image.
[ 29.177762] PM: Resume from disk failed.
[ 29.232695] kjournald starting. Commit interval 5 seconds
[ 29.232719] EXT3-fs: mounted filesystem with ordered data mode.
[ 29.496677] ieee1394: Host added: ID:BUS[0-00:1023] GUID[003095263001eff1]
[ 29.812187] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 29.988696] usb 2-1: configuration #1 chosen from 1 choice
[ 30.227753] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 30.445231] usb 3-2: configuration #1 chosen from 1 choice
[ 30.687302] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 30.955716] usb 4-1: configuration #1 chosen from 1 choice
[ 31.210716] usb 4-2: new low speed USB device using uhci_hcd and address 3
[ 31.403276] usb 4-2: configuration #1 chosen from 1 choice
[ 41.199035] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 41.245011] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 41.899808] input: Power Button (FF) as /devices/virtual/input/input1
[ 41.911540] ACPI: Power Button (FF) [PWRF]
[ 41.911736] input: Power Button (CM) as /devices/virtual/input/input2
[ 41.927528] ACPI: Power Button (CM) [PWRB]
[ 41.927740] input: Sleep Button (CM) as /devices/virtual/input/input3
[ 41.939505] ACPI: Sleep Button (CM) [SLPB]
[ 43.126493] Linux agpgart interface v0.102
[ 44.264547] nvidia: module license 'NVIDIA' taints kernel.
[ 48.344937] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 48.436858] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 24 (level, low) ->
IRQ 24
[ 48.436877] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 48.437322] NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14
17:53:07 PST 2008
[ 48.740339] usbcore: registered new interface driver hiddev
[ 48.756792] input: Logitech USB-PS/2 Optical Mouse as
/devices/pci0000:00/0000:00:10.1/usb2/2-1/2-1:1.0/input/input5
[ 48.772635] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical
Mouse] on usb-0000:00:10.1-1
[ 48.820456] input: PATEN USB HID Device as
/devices/pci0000:00/0000:00:10.3/usb4/4-1/4-1:1.0/input/input6
[ 48.832460] input,hidraw1: USB HID v1.10 Mouse [PATEN USB HID Device
] on usb-0000:00:10.3-1
[ 48.856852] input: MOSART Semi. Wireless Keyboard & Mouse as
/devices/pci0000:00/0000:00:10.3/usb4/4-2/4-2:1.0/input/input7
[ 48.868422] input,hidraw2: USB HID v1.10 Keyboard [MOSART Semi. Wireless
Keyboard & Mouse] on usb-0000:00:10.3-2
[ 48.897617] input: MOSART Semi. Wireless Keyboard & Mouse as
/devices/pci0000:00/0000:00:10.3/usb4/4-2/4-2:1.1/input/input8
[ 48.924515] input,hiddev96,hidraw3: USB HID v1.10 Mouse [MOSART Semi.
Wireless Keyboard & Mouse] on usb-0000:00:10.3-2
[ 48.924553] usbcore: registered new interface driver usbhid
[ 48.924562] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c:
v2.6:USB HID core driver
[ 49.005831] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid
0x03F0 pid 0x3202
[ 49.005868] usbcore: registered new interface driver usblp
[ 49.684411] Real Time Clock Driver v1.12ac
[ 50.553143] parport_pc 00:0c: reported by Plug and Play ACPI
[ 50.553229] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 63.534798] loop: module loaded
[ 63.581029] lp0: using parport0 (interrupt-driven).
[ 63.819449] Adding 3028212k swap on /dev/sda5. Priority:-1 extents:1
across:3028212k
[ 64.499522] EXT3 FS on sda1, internal journal
[ 66.494354] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 67.397888] No dock devices found.
[ 68.044247] longhaul: APIC detected. Longhaul is currently broken in this
configuration.
[ 68.101396] ACPI Exception (processor_perflib-0234): AE_NOT_FOUND,
Evaluating _PSS [20070126]
[ 71.511385] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 71.881811] ppdev: user-space parallel port driver
[ 72.790053] audit(1206854814.590:2): operation="inode_permission"
request_mask="a::" denied_mask="a::" name="/dev/tty" pid=5058
profile="/usr/sbin/cupsd" namespace="default"
[ 73.047385] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 73.047396] apm: overridden by ACPI.
[ 74.704190] Bluetooth: Core ver 2.11
[ 74.707991] NET: Registered protocol family 31
[ 74.708000] Bluetooth: HCI device and connection manager initialized
[ 74.708007] Bluetooth: HCI socket layer initialized
[ 74.834726] Bluetooth: L2CAP ver 2.9
[ 74.834736] Bluetooth: L2CAP socket layer initialized
[ 74.853117] Bluetooth: RFCOMM socket layer initialized
[ 74.853143] Bluetooth: RFCOMM TTY layer initialized
[ 74.853147] Bluetooth: RFCOMM ver 1.8
[ 79.413492] NET: Registered protocol family 17
[ 83.804674] NET: Registered protocol family 10
[ 83.805965] lo: Disabled Privacy Extensions
[ 94.253357] eth0: no IPv6 routers present
** Affects: pulseaudio (Ubuntu)
Importance: Undecided
Status: New
--
no audio after 8.04 upgrade
https://bugs.launchpad.net/bugs/209096
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
