Public bug reported: hello
I own an Epson Stylus cx 5900 multifunction printer/scanner/copier. I am able to use the scanner with sane (using either xsane or gscan2pdf), however it will stop half way through scanning and just sit there. I get the following dmesg output from turning on the scanner through to me starting a scan job to it stopping [ 6301.883347] usb 2-1: new high speed USB device using ehci_hcd and address 16 [ 6302.019945] usb 2-1: configuration #1 chosen from 1 choice [ 6302.026289] usblp0: USB Bidirectional printer dev 16 if 1 alt 0 proto 2 vid 0x04B8 pid 0x082E [ 6302.051236] scsi14 : SCSI emulation for USB Mass Storage devices [ 6302.059242] usb-storage: device found at 16 [ 6302.059246] usb-storage: waiting for device to settle before scanning [ 6307.056031] usb-storage: device scan complete [ 6307.060027] scsi 14:0:0:0: Direct-Access EPSON Stylus Storage 1.00 PQ: 0 ANSI: 2 [ 6307.069305] sd 14:0:0:0: [sdd] Attached SCSI removable disk [ 6307.069338] sd 14:0:0:0: Attached scsi generic sg4 type 0 [ 6336.650181] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanimage' sets config #1 [ 6336.770983] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 [ 6336.843007] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 [ 6339.762677] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 [ 6339.800864] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 [ 6340.649803] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 [ 6340.744502] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 [ 6390.838431] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 [ 6390.875980] usb 2-1: usbfs: interface 1 claimed by usblp while 'scanadf' sets config #1 I'm using ubuntu Hardy beta i386 sane, libsane, and sane-utils as found in the repos along with https://bugs.launchpad.net/ubuntu/hardy/+source/sane-backends-extras/1.0.18.12 due to this bug here https://bugs.launchpad.net/ubuntu/+source/udev/+bug/180169 I have /etc/sane.d/dll.conf to only load epkowa and the only two uncommented lines in /etc/sane.d/epkowa.conf are usb usb 0x04b8 0x082e along with this in my /etc/fstab file to give the scanner correct permissions none /dev/bus/usb usbfs auto,devmode=0666 0 0 sane-find-scanner gives me found USB scanner (vendor=0x04b8 [EPSON], product=0x082e [USB2.0 MFP(Hi-Speed)]) at libusb:002:016 also, everytime I turn off my scanner and replug it into the computer so that sane may see it again, lsusb shows the scanner under a new device number corresponding thread in the forums can be found here http://ubuntuforums.org/showthread.php?p=4569271#post4569271 ** Affects: ubuntu Importance: Undecided Status: New -- Epson Stylus cx 5900 -> usbfs: interface 1 claimed by usblp https://bugs.launchpad.net/bugs/205471 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
