Looks like the firmware version/fwcutter version issues I mentioned/referenced in my first post.
Dmesg output attached. On Thu, Mar 6, 2008 at 8:16 AM, Cory Flick <[EMAIL PROTECTED]> wrote: > Thank you for the tips and suggestions, I'll do them tonight when I get > home from work, and will reply again with my results. > > > > On Thu, Mar 6, 2008 at 8:04 AM, der_vegi <[EMAIL PROTECTED]> wrote: > > > Cory, what i your output of 'dmesg'? This would give an idea, if the > > problem is the driver itself, or a problem of not loading the firmware. > > > > A second aproach would be to do the steps, the install script shoud do, > > manually (steps extracted from > > /usr/share/b43-fwcutter/install_bcm43xx_firmware.sh): > > go to some temporary directory, for example ~/b43-temp and perform the > > following steps: > > > > cd ~ > > mkdir b43-temp > > cd b43-temp > > wget http://downloads.openwrt.org/sources/wl_apsta-3.130.20.0.o > > wget http://downloads.openwrt.org/sources/broadcom-wl-4.80.53.0.tar.bz2 > > sudo b43-fwcutter -w /lib/firmware wl_apsta-3.130.20.0.o > > tar xfvj broadcom-wl-4.80.53.0.tar.bz2 > > sudo b43-fwcutter -w /lib/firmware broadcom-wl-4.80.53.0/kmod/wl_apsta.o > > sudo chmod o+rx /lib/firmware/b43 /lib/firmware/b43legacy > > > > Again, output of 'dmesg' would be helpful... Good luck! > > > > -- > > broadcom wireless not working fresh install of hardy > > https://bugs.launchpad.net/bugs/197819 > > You received this bug notification because you are a direct subscriber > > of the bug. > > > > Status in Source Package "b43-fwcutter" in Ubuntu: New > > Status in Source Package "jockey" in Ubuntu: New > > > > Bug description: > > [EMAIL PROTECTED]:~$ cat /etc/lsb-release > > DISTRIB_ID=Ubuntu > > DISTRIB_RELEASE=8.04 > > DISTRIB_CODENAME=hardy > > DISTRIB_DESCRIPTION="Ubuntu hardy (development branch)" > > [EMAIL PROTECTED]:~$ uname -a > > Linux lil-spooky 2.6.24-11-generic #1 SMP Fri Feb 29 21:26:31 UTC 2008 > > x86_64 GNU/Linux > > > > ------------------------------------------------------------------------------------------------- > > [EMAIL PROTECTED]:~$ apt-cache policy b43-fwcutter > > b43-fwcutter: > > Installed: 1:008-2 > > Candidate: 1:008-2 > > Version table: > > *** 1:008-2 0 > > 500 http://us.archive.ubuntu.com hardy/universe Packages > > 100 /var/lib/dpkg/status > > > > ---------------------------------------------------------------------------------------------------------------------------- > > what I expected to happen : after doing a fresh install of Hardy Alpha > > 5, I started the Restricted Driver Manager to install the broadcom firmware > > to get my wireless working, just like I did in Gutsy. I expected the > > fwcutter package to download and install the correct firmware, which is what > > happened under Gutsy. In Gutsy, the little orange light turned blue right > > away ( my machine is an HP dv6000 series laptop ) indicating that wireless > > is up and running. > > > > ------------------------------------------------------------------------------------------------------------------------------ > > what happened instead : started the Restricted Driver manager now called > > "Hardware Drivers" under System-->Administration, clicked the checkbox for > > the Broadcom firmware to be downloaded and installed. The Hardware Driver > > manager told me it had downloaded and installed the firmware, however, the > > orange light did not turn blue. I tried rebooting to see if that would make > > a difference. It did not make a difference. No working wireless. This page : > > http://linuxwireless.org/en/users/Drivers/b43 seems to indicate that > > various kernel versions need not just different versions of the firmware, > > but different versions of the fwcutter program/package itself, as well. > > Would be great if that could be integrated into Hardy before final release. > > > > ---------------------------------------------------------------------------------------------------------------------------------- > > > > [ 0.000000] Linux version 2.6.24-11-generic ([EMAIL PROTECTED]) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu1)) #1 SMP Fri Feb 29 21:26:31 UTC 2008 (Ubuntu 2.6.24-11.17-generic) [ 0.000000] Command line: root=UUID=b54d357e-4a50-4363-a0e0-3879cb691870 ro quiet splash noapic [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable) [ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003df00000 (usable) [ 0.000000] BIOS-e820: 000000003df00000 - 000000003df17000 (ACPI data) [ 0.000000] BIOS-e820: 000000003df17000 - 000000003df80000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003df80000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 157) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 253696) 1 entries of 3200 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP signature @ 0xFFFF8100000F8990 checksum 0 [ 0.000000] ACPI: RSDP 000F8990, 0014 (r0 HP ) [ 0.000000] ACPI: RSDT 3DF0FB99, 0038 (r1 HP RSDT 6040000 LTP 0) [ 0.000000] ACPI: FACP 3DF16D52, 0074 (r1 HP MCP51M 6040000 PTL_ F4240) [ 0.000000] ACPI: DSDT 3DF0FBD1, 7181 (r1 HP MCP51M 6040000 MSFT 100000E) [ 0.000000] ACPI: FACS 3DF17FC0, 0040 [ 0.000000] ACPI: SSDT 3DF16DC6, 0182 (r1 HP POWERNOW 6040000 LTP 1) [ 0.000000] ACPI: MCFG 3DF16F48, 003C (r1 HP MCFG 6040000 LTP 0) [ 0.000000] ACPI: APIC 3DF16F84, 0054 (r1 HP APIC 6040000 LTP 0) [ 0.000000] ACPI: BOOT 3DF16FD8, 0028 (r1 HP $SBFTBL$ 6040000 LTP 1) [ 0.000000] ACPI: DMI detected: Hewlett-Packard [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] CPU has 2 num_cores [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-000000003df00000 [ 0.000000] Entering add_active_range(0, 0, 157) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 253696) 1 entries of 3200 used [ 0.000000] Bootmem setup node 0 0000000000000000-000000003df00000 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 157 [ 0.000000] 0: 256 -> 253696 [ 0.000000] On node 0 totalpages: 253597 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1210 pages reserved [ 0.000000] DMA zone: 2731 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 3412 pages used for memmap [ 0.000000] DMA32 zone: 246188 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. [ 0.000000] If you got timer trouble try acpi_use_timer_override [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option. [ 0.000000] Using ACPI for processor (LAPIC) configuration information [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: nVIDIA MPTABLE: Product ID: C51-MCP51 MPTABLE: APIC at: 0xFEE00000 [ 0.000000] I/O APIC #2 at 0xFEC00000. [ 0.000000] Setting APIC routing to flat [ 0.000000] Processors: 2 [ 0.000000] swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000 [ 0.000000] swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000d2000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 34656 bytes of per cpu data [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 248919 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: root=UUID=b54d357e-4a50-4363-a0e0-3879cb691870 ro quiet splash noapic [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] TSC calibrated against PM_TIMER [ 14.220292] Marking TSC unstable due to TSCs unsynchronized [ 14.220295] time.c: Detected 1607.309 MHz processor. [ 14.223831] Console: colour VGA+ 80x25 [ 14.223835] console [tty0] enabled [ 14.223854] Checking aperture... [ 14.223857] CPU 0: aperture @ e378000000 size 32 MB [ 14.223860] Aperture too small (32 MB) [ 14.231301] No AGP bridge found [ 14.243161] Memory: 988088k/1014784k available (2465k kernel code, 26300k reserved, 1310k data, 316k init) [ 14.243196] SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 14.322270] Calibrating delay using timer specific routine.. 3217.72 BogoMIPS (lpj=6435450) [ 14.322306] Security Framework initialized [ 14.322312] SELinux: Disabled at boot. [ 14.322327] AppArmor: AppArmor initialized [ 14.322331] Failure registering capabilities with primary security module. [ 14.322438] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 14.323245] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 14.323622] Mount-cache hash table entries: 256 [ 14.323763] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 14.323766] CPU: L2 Cache: 256K (64 bytes/line) [ 14.323770] CPU 0/0 -> Node 0 [ 14.323772] CPU: Physical Processor ID: 0 [ 14.323774] CPU: Processor Core ID: 0 [ 14.323799] SMP alternatives: switching to UP code [ 14.324413] Early unpacking initramfs... done [ 14.697143] ACPI: Core revision 20070126 [ 14.697215] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 14.699548] ACPI: setting ELCR to 0200 (from 0ca0) [ 14.907510] Disabling APIC timer [ 14.907654] SMP alternatives: switching to SMP code [ 14.908168] Booting processor 1/2 APIC 0x1 [ 14.918336] Initializing CPU#1 [ 14.919654] spurious 8259A interrupt: IRQ7. [ 14.995652] Calibrating delay using timer specific routine.. 3220.91 BogoMIPS (lpj=6441825) [ 14.995659] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 14.995662] CPU: L2 Cache: 256K (64 bytes/line) [ 14.995665] CPU 1/1 -> Node 0 [ 14.995666] CPU: Physical Processor ID: 0 [ 14.995668] CPU: Processor Core ID: 1 [ 14.995737] AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02 [ 14.995707] Brought up 2 CPUs [ 14.995764] CPU0 attaching sched-domain: [ 14.995767] domain 0: span 03 [ 14.995770] groups: 01 02 [ 14.995773] domain 1: span 03 [ 14.995775] groups: 03 [ 14.995777] CPU1 attaching sched-domain: [ 14.995779] domain 0: span 03 [ 14.995781] groups: 02 01 [ 14.995784] domain 1: span 03 [ 14.995785] groups: 03 [ 14.996061] net_namespace: 120 bytes [ 14.996677] Time: 2:47:18 Date: 03/07/08 [ 14.996738] NET: Registered protocol family 16 [ 14.996961] ACPI: bus type pci registered [ 14.997046] PCI: Using configuration type 1 [ 14.998191] ACPI: EC: Look up EC in DSDT [ 15.000001] ACPI: Interpreter enabled [ 15.000005] ACPI: (supports S0 S3 S4 S5) [ 15.000022] ACPI: Using PIC for interrupt routing [ 15.000868] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 15.006622] ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62 [ 15.006627] ACPI: EC: driver started in interrupt mode [ 15.006694] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 15.008164] PCI: Transparent bridge - 0000:00:10.0 [ 15.008184] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 15.008298] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] [ 15.008332] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT] [ 15.008369] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT] [ 15.042594] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.042780] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 *11 14 15) [ 15.042960] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15) [ 15.043137] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.043315] ACPI: PCI Interrupt Link [LK1E] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.043493] ACPI: PCI Interrupt Link [LK2E] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.043723] ACPI: PCI Interrupt Link [LK3E] (IRQs 5 7 9 10 *11 14 15) [ 15.043901] ACPI: PCI Interrupt Link [LK4E] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.044083] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15) [ 15.044262] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 *10 11 14 15) [ 15.044441] ACPI: PCI Interrupt Link [LUS0] (IRQs 5 7 9 10 *11 14 15) [ 15.044620] ACPI: PCI Interrupt Link [LUS2] (IRQs 5 *7 9 10 11 14 15) [ 15.044799] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15) [ 15.044976] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.045155] ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.045333] ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.045511] ACPI: PCI Interrupt Link [LPID] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 15.045699] ACPI: PCI Interrupt Link [LTID] (IRQs *5 7 9 10 11 14 15) [ 15.045878] ACPI: PCI Interrupt Link [LSI1] (IRQs 5 7 9 *10 11 14 15) [ 15.046048] Linux Plug and Play Support v0.97 (c) Adam Belay [ 15.046084] pnp: PnP ACPI init [ 15.046095] ACPI: bus type pnp registered [ 15.048608] pnp: PnP ACPI: found 11 devices [ 15.048612] ACPI: ACPI bus type pnp unregistered [ 15.048892] PCI: Using ACPI for IRQ routing [ 15.048897] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 15.067590] NET: Registered protocol family 8 [ 15.067593] NET: Registered protocol family 20 [ 15.067744] AppArmor: AppArmor Filesystem Enabled [ 15.083589] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved [ 15.083594] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved [ 15.083597] system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved [ 15.083600] system 00:00: iomem range 0x0-0x0 could not be reserved [ 15.083610] system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved [ 15.083618] system 00:03: ioport range 0x1000-0x107f has been reserved [ 15.083621] system 00:03: ioport range 0x1080-0x10ff has been reserved [ 15.083624] system 00:03: ioport range 0x1400-0x147f has been reserved [ 15.083627] system 00:03: ioport range 0x1480-0x14ff has been reserved [ 15.083630] system 00:03: ioport range 0x1800-0x187f has been reserved [ 15.083634] system 00:03: ioport range 0x1880-0x18ff has been reserved [ 15.083637] system 00:03: ioport range 0x2000-0x203f has been reserved [ 15.083645] system 00:04: ioport range 0x360-0x361 has been reserved [ 15.083649] system 00:04: ioport range 0x380-0x383 has been reserved [ 15.083652] system 00:04: ioport range 0x4d0-0x4d1 has been reserved [ 15.084135] PCI: Bridge: 0000:00:02.0 [ 15.084138] IO window: 4000-4fff [ 15.084141] MEM window: b3000000-b31fffff [ 15.084143] PREFETCH window: d0000000-d01fffff [ 15.084146] PCI: Bridge: 0000:00:03.0 [ 15.084148] IO window: disabled. [ 15.084150] MEM window: b3200000-b33fffff [ 15.084153] PREFETCH window: disabled. [ 15.084158] PCI: Bridge: 0000:00:10.0 [ 15.084159] IO window: disabled. [ 15.084162] MEM window: b3400000-b34fffff [ 15.084165] PREFETCH window: disabled. [ 15.084181] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 15.084189] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 15.084198] PCI: Setting latency timer of device 0000:00:10.0 to 64 [ 15.084281] NET: Registered protocol family 2 [ 15.087535] Time: acpi_pm clocksource has been installed. [ 15.087656] Clockevents: could not switch to one-shot mode:<6>Clockevents: could not switch to one-shot mode: lapic is not functional. [ 15.087552] Could not switch to high resolution mode on CPU 0 [ 15.087666] lapic is not functional. [ 15.087668] Could not switch to high resolution mode on CPU 1 [ 15.131642] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 15.132188] TCP established hash table entries: 131072 (order: 9, 2097152 bytes) [ 15.133841] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 15.134606] TCP: Hash tables configured (established 131072 bind 65536) [ 15.134611] TCP reno registered [ 15.147703] checking if image is initramfs... it is [ 15.587620] Clockevents: could not switch to one-shot mode:<6>Clockevents: could not switch to one-shot mode: lapic is not functional. [ 15.587507] Could not switch to high resolution mode on CPU 0 [ 15.587632] lapic is not functional. [ 15.587634] Could not switch to high resolution mode on CPU 1 [ 15.881888] Freeing initrd memory: 7409k freed [ 15.887328] Simple Boot Flag at 0x36 set to 0x1 [ 15.888404] audit: initializing netlink socket (disabled) [ 15.888417] audit(1204858038.472:1): initialized [ 15.890855] VFS: Disk quotas dquot_6.5.1 [ 15.890949] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 15.891100] io scheduler noop registered [ 15.891103] io scheduler anticipatory registered [ 15.891105] io scheduler deadline registered [ 15.891225] io scheduler cfq registered (default) [ 15.891242] Boot video device is 0000:00:05.0 [ 16.107898] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 16.107928] assign_interrupt_mode Found MSI capability [ 16.107951] Allocate Port Service[0000:00:02.0:pcie00] [ 16.108026] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 16.108053] assign_interrupt_mode Found MSI capability [ 16.108072] Allocate Port Service[0000:00:03.0:pcie00] [ 16.142116] Real Time Clock Driver v1.12ac [ 16.142230] Linux agpgart interface v0.102 [ 16.142233] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 16.143885] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 16.143975] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 16.144089] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 16.160891] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 16.160897] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 16.175537] mice: PS/2 mouse device common for all mice [ 16.175585] cpuidle: using governor ladder [ 16.175587] cpuidle: using governor menu [ 16.175752] NET: Registered protocol family 1 [ 16.175810] registered taskstats version 1 [ 16.175975] Magic number: 0:949:762 [ 16.175979] hash matches device serio0 [ 16.176114] /build/buildd/linux-2.6.24/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 16.176118] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 16.176121] EDD information not available. [ 16.176130] Freeing unused kernel memory: 316k freed [ 16.187027] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 17.439362] fuse init (API version 7.9) [ 17.454427] ACPI: Thermal Zone [THRM] (31 C) [ 18.015760] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 11 [ 18.015765] PCI: setting IRQ 11 as level-triggered [ 18.015770] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LK1E] -> GSI 11 (level, low) -> IRQ 11 [ 18.015781] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 18.043894] SCSI subsystem initialized [ 18.065088] ssb: SPROM revision 2 detected. [ 18.081182] usbcore: registered new interface driver usbfs [ 18.081206] usbcore: registered new interface driver hub [ 18.083392] ssb: Sonics Silicon Backplane found on PCI device 0000:03:00.0 [ 18.087334] usbcore: registered new device driver usb [ 18.128639] libata version 3.00 loaded. [ 18.128676] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 18.129008] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 11 [ 18.129012] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 11 (level, low) -> IRQ 11 [ 18.129133] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 18.129141] ohci_hcd 0000:00:0b.0: OHCI Host Controller [ 18.129481] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1 [ 18.129506] ohci_hcd 0000:00:0b.0: irq 11, io mem 0xb0004000 [ 18.185481] usb usb1: configuration #1 chosen from 1 choice [ 18.185509] hub 1-0:1.0: USB hub found [ 18.185520] hub 1-0:1.0: 8 ports detected [ 18.287828] sata_nv 0000:00:0e.0: version 3.5 [ 18.287851] PCI: Enabling device 0000:00:0e.0 (0005 -> 0007) [ 18.288140] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 5 [ 18.288143] PCI: setting IRQ 5 as level-triggered [ 18.288148] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 5 (level, low) -> IRQ 5 [ 18.288301] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 18.288453] scsi0 : sata_nv [ 18.288519] scsi1 : sata_nv [ 18.288692] ata1: SATA max UDMA/133 cmd 0x30c0 ctl 0x30b4 bmdma 0x3090 irq 5 [ 18.288696] ata2: SATA max UDMA/133 cmd 0x30b8 ctl 0x30b0 bmdma 0x3098 irq 5 [ 18.595282] usb 1-1: new low speed USB device using ohci_hcd and address 2 [ 18.755271] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 18.763453] ata1.00: ATA-7: ST9100824AS, 7.24, max UDMA/100 [ 18.763457] ata1.00: 195371568 sectors, multi 16: LBA48 [ 18.779455] ata1.00: configured for UDMA/100 [ 18.810374] usb 1-1: configuration #1 chosen from 1 choice [ 19.092669] ata2: SATA link down (SStatus 0 SControl 300) [ 19.103453] scsi 0:0:0:0: Direct-Access ATA ST9100824AS 7.24 PQ: 0 ANSI: 5 [ 19.104344] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10 [ 19.104350] PCI: setting IRQ 10 as level-triggered [ 19.104355] ACPI: PCI Interrupt 0000:07:05.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10 [ 19.105821] pata_amd 0000:00:0d.0: version 0.3.10 [ 19.105879] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 19.127227] usb 1-4: new full speed USB device using ohci_hcd and address 3 [ 19.156617] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[b3400000-b34007ff] Max Packet=[2048] IR/IT contexts=[4/4] [ 19.162059] scsi2 : pata_amd [ 19.162135] scsi3 : pata_amd [ 19.162827] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x3080 irq 14 [ 19.162831] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x3088 irq 15 [ 19.382289] usb 1-4: configuration #1 chosen from 1 choice [ 19.388343] usbcore: registered new interface driver hiddev [ 19.393380] input: A4Tech PS/2+USB Mouse as /devices/pci0000:00/0000:00:0b.0/usb1/1-1/1-1:1.0/input/input2 [ 19.415279] input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:0b.0-1 [ 19.415302] usbcore: registered new interface driver usbhid [ 19.415307] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 19.479671] ata3.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2 [ 19.651432] ata3.00: configured for MWDMA2 [ 19.651475] ata4: port disabled. ignoring. [ 19.655434] scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4084N KQ09 PQ: 0 ANSI: 5 [ 19.656732] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. [ 19.657046] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 10 [ 19.657050] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 10 (level, low) -> IRQ 10 [ 19.657058] PCI: Setting latency timer of device 0000:00:14.0 to 64 [ 20.175614] forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x20 @ 1, addr 00:16:36:a1:4a:c9 [ 20.175620] forcedeth 0000:00:14.0: highdma pwrctl timirq lnktim desc-v3 [ 20.176341] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 7 [ 20.176346] PCI: setting IRQ 7 as level-triggered [ 20.176351] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUS2] -> GSI 7 (level, low) -> IRQ 7 [ 20.176462] PCI: Setting latency timer of device 0000:00:0b.1 to 64 [ 20.176470] ehci_hcd 0000:00:0b.1: EHCI Host Controller [ 20.176531] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2 [ 20.176568] ehci_hcd 0000:00:0b.1: debug port 1 [ 20.176573] PCI: cache line size of 64 is not supported by device 0000:00:0b.1 [ 20.176583] ehci_hcd 0000:00:0b.1: irq 7, io mem 0xb0005000 [ 20.176889] usb 1-1: USB disconnect, address 2 [ 20.187139] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 20.187268] usb usb2: configuration #1 chosen from 1 choice [ 20.187296] hub 2-0:1.0: USB hub found [ 20.187304] hub 2-0:1.0: 8 ports detected [ 20.302610] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 20.302617] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 20.308127] Driver 'sd' needs updating - please use bus_type methods [ 20.308232] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 20.308248] sd 0:0:0:0: [sda] Write Protect is off [ 20.308251] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 20.308272] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 20.308328] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 20.308340] sd 0:0:0:0: [sda] Write Protect is off [ 20.308343] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 20.308363] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 20.308368] sda: sda1 sda2 sda3 [ 20.319145] usb 1-4: USB disconnect, address 3 [ 20.327994] Driver 'sr' needs updating - please use bus_type methods [ 20.333314] sd 0:0:0:0: [sda] Attached SCSI disk [ 20.339203] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 20.339230] sr 2:0:0:0: Attached scsi generic sg1 type 5 [ 20.355188] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 20.355195] Uniform CD-ROM driver Revision: 3.20 [ 20.355259] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 20.431405] ieee1394: Host added: ID:BUS[0-00:1023] GUID[009fc00099a9c300] [ 20.538880] Attempting manual resume [ 20.538884] swsusp: Resume From Partition 8:2 [ 20.538886] PM: Checking swsusp image. [ 20.539085] PM: Resume from disk failed. [ 20.554612] EXT3-fs: INFO: recovery required on readonly filesystem. [ 20.554617] EXT3-fs: write access will be enabled during recovery. [ 20.871092] usb 2-4: new high speed USB device using ehci_hcd and address 3 [ 21.013608] usb 2-4: configuration #1 chosen from 1 choice [ 21.315057] usb 1-1: new low speed USB device using ohci_hcd and address 4 [ 21.528997] usb 1-1: configuration #1 chosen from 1 choice [ 21.543164] input: A4Tech PS/2+USB Mouse as /devices/pci0000:00/0000:00:0b.0/usb1/1-1/1-1:1.0/input/input3 [ 21.575525] input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:0b.0-1 [ 24.176353] kjournald starting. Commit interval 5 seconds [ 24.176378] EXT3-fs: sda1: orphan cleanup on readonly fs [ 24.176386] ext3_orphan_cleanup: deleting unreferenced inode 1221988 [ 24.176417] EXT3-fs: sda1: 1 orphan inode deleted [ 24.176419] EXT3-fs: recovery complete. [ 24.186418] EXT3-fs: mounted filesystem with ordered data mode. [ 32.842746] ip_tables: (C) 2000-2006 Netfilter Core Team [ 32.903542] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 33.606951] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 33.638385] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 33.767722] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040 [ 33.767757] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000 [ 33.874387] input: Power Button (FF) as /devices/virtual/input/input4 [ 33.910239] ACPI: Power Button (FF) [PWRF] [ 33.910378] input: Power Button (CM) as /devices/virtual/input/input5 [ 33.942247] ACPI: Power Button (CM) [PWRB] [ 33.942382] input: Sleep Button (CM) as /devices/virtual/input/input6 [ 33.978226] ACPI: Sleep Button (CM) [SLPB] [ 33.978331] input: Lid Switch as /devices/virtual/input/input7 [ 33.978458] ACPI: Lid Switch [LID] [ 34.010873] nvidia: module license 'NVIDIA' taints kernel. [ 34.339586] ACPI: AC Adapter [ACAD] (on-line) [ 34.858589] ACPI: Battery Slot [BAT0] (battery present) [ 34.858677] ACPI: WMI-Acer: Mapper loaded [ 34.859121] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:00/input/input8 [ 34.882175] ACPI: Video Device [UVGA] (multi-head: yes rom: no post: no) [ 34.947395] ACPI: PCI Interrupt Link [LK3E] enabled at IRQ 11 [ 34.947401] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LK3E] -> GSI 11 (level, low) -> IRQ 11 [ 34.947409] PCI: Setting latency timer of device 0000:00:05.0 to 64 [ 34.947595] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.12 Thu Feb 14 17:51:09 PST 2008 [ 35.326203] Linux video capture interface: v2.00 [ 35.461039] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (0c45:62c0) [ 35.483072] usbcore: registered new interface driver uvcvideo [ 35.483078] USB Video Class driver (v0.1.0) [ 35.874087] b43-phy0: Broadcom 4311 WLAN found [ 35.918178] ricoh-mmc: Ricoh MMC Controller disabling driver [ 35.918183] ricoh-mmc: Copyright(c) Philip Langdale [ 35.951689] sdhci: Secure Digital Host Controller Interface driver [ 35.951695] sdhci: Copyright(c) Pierre Ossman [ 35.981187] phy0: Selected rate control algorithm 'simple' [ 36.074156] input: PC Speaker as /devices/platform/pcspkr/input/input9 [ 36.184959] ricoh-mmc: Ricoh MMC controller found at 0000:07:05.2 [1180:0843] (rev 1) [ 36.184973] ricoh-mmc: Controller is now disabled. [ 36.185145] sdhci: SDHCI controller found at 0000:07:05.1 [1180:0822] (rev 19) [ 36.185460] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 11 [ 36.185465] ACPI: PCI Interrupt 0000:07:05.1[B] -> Link [LNK2] -> GSI 11 (level, low) -> IRQ 11 [ 36.185644] sdhci:slot0: Will use DMA mode even though HW doesn't fully claim to support it. [ 36.185730] mmc0: SDHCI at 0xb3400800 irq 11 DMA [ 36.765718] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 9 [ 36.765724] PCI: setting IRQ 9 as level-triggered [ 36.765728] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 9 (level, low) -> IRQ 9 [ 36.765853] PCI: Setting latency timer of device 0000:00:10.1 to 64 [ 36.924570] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000 [ 36.982667] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10 [ 37.871802] udev: renamed network interface wmaster0 to eth1 [ 69.981680] lp: driver loaded but no devices found [ 70.172744] Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k [ 70.783415] EXT3 FS on sda1, internal journal [ 82.748958] kjournald starting. Commit interval 5 seconds [ 82.749211] EXT3 FS on sda3, internal journal [ 82.749216] EXT3-fs: mounted filesystem with ordered data mode. [ 83.814030] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' [ 83.831495] No dock devices found. [ 84.112080] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-50 processors (2 cpu cores) (version 2.20.00) [ 84.111950] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13 [ 84.111955] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e [ 87.139640] input: b43-phy0 as /devices/virtual/input/input11 [ 87.200333] NET: Registered protocol family 10 [ 87.305986] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 87.305994] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 87.306102] lo: Disabled Privacy Extensions [ 87.421223] ppdev: user-space parallel port driver [ 87.719019] audit(1204858111.180:2): operation="inode_permission" request_mask="a::" denied_mask="a::" name="/dev/tty" pid=8175 profile="/usr/sbin/cupsd" namespace="default" [ 88.080087] Bluetooth: Core ver 2.11 [ 88.080563] NET: Registered protocol family 31 [ 88.080567] Bluetooth: HCI device and connection manager initialized [ 88.080572] Bluetooth: HCI socket layer initialized [ 88.126299] Bluetooth: L2CAP ver 2.9 [ 88.126304] Bluetooth: L2CAP socket layer initialized [ 88.174960] Bluetooth: RFCOMM socket layer initialized [ 88.174981] Bluetooth: RFCOMM TTY layer initialized [ 88.174983] Bluetooth: RFCOMM ver 1.8 [ 89.119814] Clocksource tsc unstable (delta = -166030939 ns) [ 90.110409] input: b43-phy0 as /devices/virtual/input/input12 [ 90.166280] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 90.166290] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 91.510735] NET: Registered protocol family 17 [ 98.407615] eth0: no IPv6 routers present [ 100.185453] input: b43-phy0 as /devices/virtual/input/input13 [ 100.227498] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 100.227506] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 101.955786] Inbound IN=eth0 OUT= MAC=00:16:36:a1:4a:c9:00:0f:35:44:68:01:08:00 SRC=24.64.8.82 DST=72.128.105.5 LEN=512 TOS=0x00 PREC=0x00 TTL=66 ID=13588 PROTO=UDP SPT=22356 DPT=1027 LEN=492 [ 101.955978] Inbound IN=eth0 OUT= MAC=00:16:36:a1:4a:c9:00:0f:35:44:68:01:08:00 SRC=24.64.8.82 DST=72.128.105.5 LEN=512 TOS=0x00 PREC=0x00 TTL=66 ID=13587 PROTO=UDP SPT=22356 DPT=1026 LEN=492 [ 101.956084] Inbound IN=eth0 OUT= MAC=00:16:36:a1:4a:c9:00:0f:35:44:68:01:08:00 SRC=24.64.8.82 DST=72.128.105.5 LEN=512 TOS=0x00 PREC=0x00 TTL=66 ID=13589 PROTO=UDP SPT=22356 DPT=1028 LEN=492 [ 108.044651] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=6678 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 109.340804] input: b43-phy0 as /devices/virtual/input/input14 [ 109.382665] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 109.382673] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 118.528811] input: b43-phy0 as /devices/virtual/input/input15 [ 118.570425] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 118.570433] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 127.683446] input: b43-phy0 as /devices/virtual/input/input16 [ 127.723349] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 127.723357] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 136.843325] input: b43-phy0 as /devices/virtual/input/input17 [ 136.890662] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 136.890670] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 149.670457] CPU0 attaching NULL sched-domain. [ 149.670467] CPU1 attaching NULL sched-domain. [ 149.684838] CPU0 attaching sched-domain: [ 149.684845] domain 0: span 03 [ 149.684847] groups: 01 02 [ 149.684851] domain 1: span 03 [ 149.684853] groups: 03 [ 149.684855] CPU1 attaching sched-domain: [ 149.684857] domain 0: span 03 [ 149.684859] groups: 02 01 [ 149.684862] domain 1: span 03 [ 149.684864] groups: 03 [ 150.383673] input: b43-phy0 as /devices/virtual/input/input18 [ 150.451254] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 150.451265] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 157.652953] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=349 TOS=0x00 PREC=0x00 TTL=255 ID=6926 PROTO=UDP SPT=67 DPT=68 LEN=329 [ 167.669588] input: b43-phy0 as /devices/virtual/input/input19 [ 167.711767] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 167.711775] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 174.699172] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=354 TOS=0x00 PREC=0x00 TTL=255 ID=7022 PROTO=UDP SPT=67 DPT=68 LEN=334 [ 176.932162] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=349 TOS=0x00 PREC=0x00 TTL=255 ID=7054 PROTO=UDP SPT=67 DPT=68 LEN=329 [ 176.941726] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=349 TOS=0x00 PREC=0x00 TTL=255 ID=7055 PROTO=UDP SPT=67 DPT=68 LEN=329 [ 179.587911] irq 7: nobody cared (try booting with the "irqpoll" option) [ 179.587923] Pid: 0, comm: swapper Tainted: P 2.6.24-11-generic #1 [ 179.587925] [ 179.587926] Call Trace: [ 179.587928] <IRQ> [<ffffffff8027ad9e>] __report_bad_irq+0x1e/0x80 [ 179.587966] [<ffffffff8027b0ad>] note_interrupt+0x2ad/0x2e0 [ 179.587980] [<ffffffff8027be63>] handle_level_irq+0xb3/0x120 [ 179.587991] [<ffffffff8020ef6b>] do_IRQ+0x7b/0x100 [ 179.587994] [<ffffffff8020b390>] default_idle+0x0/0x40 [ 179.587998] [<ffffffff8020b390>] default_idle+0x0/0x40 [ 179.588001] [<ffffffff8020c891>] ret_from_intr+0x0/0xa [ 179.588005] <EOI> [<ffffffff8020b3b9>] default_idle+0x29/0x40 [ 179.588027] [<ffffffff8020b43f>] cpu_idle+0x6f/0xc0 [ 179.588058] [ 179.588059] handlers: [ 179.588060] [<ffffffff880682c0>] (usb_hcd_irq+0x0/0x60 [usbcore]) [ 179.588084] Disabling IRQ #7 [ 180.691100] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7090 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 206.606767] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7234 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 206.886968] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=351 TOS=0x00 PREC=0x00 TTL=255 ID=7252 PROTO=UDP SPT=67 DPT=68 LEN=331 [ 223.166075] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7337 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 223.664198] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=349 TOS=0x00 PREC=0x00 TTL=255 ID=7350 PROTO=UDP SPT=67 DPT=68 LEN=329 [ 229.931970] Inbound IN=eth0 OUT= MAC=00:16:36:a1:4a:c9:00:0f:35:44:68:01:08:00 SRC=122.136.45.47 DST=72.128.105.5 LEN=915 TOS=0x00 PREC=0x80 TTL=43 ID=0 DF PROTO=UDP SPT=60332 DPT=1027 LEN=895 [ 229.934334] Inbound IN=eth0 OUT= MAC=00:16:36:a1:4a:c9:00:0f:35:44:68:01:08:00 SRC=122.136.45.47 DST=72.128.105.5 LEN=915 TOS=0x00 PREC=0x80 TTL=43 ID=0 DF PROTO=UDP SPT=60332 DPT=1026 LEN=895 [ 237.314546] input: b43-phy0 as /devices/virtual/input/input20 [ 237.365990] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 237.366000] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 262.225639] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7503 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 270.574730] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=348 TOS=0x00 PREC=0x00 TTL=255 ID=7532 PROTO=UDP SPT=67 DPT=68 LEN=328 [ 272.122796] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=347 TOS=0x00 PREC=0x00 TTL=255 ID=7544 PROTO=UDP SPT=67 DPT=68 LEN=327 [ 275.092911] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7583 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 281.430760] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=339 TOS=0x00 PREC=0x00 TTL=255 ID=7629 PROTO=UDP SPT=67 DPT=68 LEN=319 [ 283.872312] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7661 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 285.109850] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=349 TOS=0x00 PREC=0x00 TTL=255 ID=7681 PROTO=UDP SPT=67 DPT=68 LEN=329 [ 297.421964] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7751 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 298.936749] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7769 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 299.176509] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=333 TOS=0x00 PREC=0x00 TTL=255 ID=7781 PROTO=UDP SPT=67 DPT=68 LEN=313 [ 312.209963] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7842 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 323.533932] input: b43-phy0 as /devices/virtual/input/input21 [ 323.612260] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed. [ 323.612269] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 4). [ 333.616939] Inbound IN=eth0 OUT= MAC=00:16:36:a1:4a:c9:00:0f:35:44:68:01:08:00 SRC=71.76.55.67 DST=72.128.105.5 LEN=63 TOS=0x00 PREC=0x00 TTL=113 ID=3583 PROTO=UDP SPT=19007 DPT=20495 LEN=43 [ 337.652416] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=7952 PROTO=UDP SPT=67 DPT=68 LEN=310 [ 339.948668] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=349 TOS=0x00 PREC=0x00 TTL=255 ID=7984 PROTO=UDP SPT=67 DPT=68 LEN=329 [ 346.852716] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=348 TOS=0x00 PREC=0x00 TTL=255 ID=8022 PROTO=UDP SPT=67 DPT=68 LEN=328 [ 348.864930] Inbound IN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0f:35:44:68:01:08:00 SRC=76.38.64.1 DST=255.255.255.255 LEN=330 TOS=0x00 PREC=0x00 TTL=255 ID=8046 PROTO=UDP SPT=67 DPT=68 LEN=310 -- broadcom wireless not working fresh install of hardy https://bugs.launchpad.net/bugs/197819 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
