i have 7.10 with kernel 2.6.22-14-rt using a wintv card. i have the same problem: the line out of the wintv card is not working. well almost cause i can hear a little bit if i really boost the sound on my amplifier (+30db).
i was hoping to use btaudio to driver the 32000 hertz to /dev/dsp2 (or so). but modprobe btaudio is not present. locate btaudio gives nothing. maybe it's my configuration. [ 45.692860] bttv: driver version 0.9.17 loaded [ 45.692868] bttv: using 8 buffers with 2080k (520 pages) each for capture [ 45.692954] bttv: Bt8xx card found (0). [ 45.692983] ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 20 [ 45.692998] bttv0: Bt878 (rev 17) at 0000:02:0a.0, irq: 20, latency: 64, mmio: 0xf8ffe000 [ 45.693015] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb [ 45.693019] bttv0: using: Hauppauge (bt878) [card=10,autodetected] [ 45.693052] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] [ 45.695773] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] [ 45.753326] tveeprom 0-0050: Hauppauge model 44811, rev C323, serial# 2631909 [ 45.753332] tveeprom 0-0050: tuner model is Philips FM1236 (idx 23, type 2) [ 45.753336] tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) [ 45.753340] tveeprom 0-0050: audio processor is None (idx 0) [ 45.753343] tveeprom 0-0050: has radio [ 45.753346] bttv0: Hauppauge eeprom indicates model#44811 [ 45.753349] bttv0: using tuner=2 [ 45.753354] bttv0: i2c: checking for MSP34xx @ 0x80... not found [ 45.753946] bttv0: i2c: checking for TDA9875 @ 0xb0... not found [ 45.754528] bttv0: i2c: checking for TDA7432 @ 0x8a... not found [ 45.802424] bttv0: i2c: checking for TDA9887 @ 0x86... not found [ 45.854762] tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw]) [ 45.854803] tuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) [ 45.854808] tuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) [ 45.863597] bttv0: registered device video0 [ 45.863647] bttv0: registered device vbi0 [ 45.863689] bttv0: registered device radio0 [ 45.863713] bttv0: PLL: 28636363 => 35468950 .. ok [ 45.886293] bttv: Bt8xx card found (1). [ 45.886319] ACPI: PCI Interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 45.886334] bttv1: Bt878 (rev 17) at 0000:02:0d.0, irq: 21, latency: 64, mmio: 0xf8ffc000 [ 45.886360] bttv1: detected: Osprey-200 [card=88], PCI subsystem ID is 0070:ff01 [ 45.886364] bttv1: using: Osprey 200/250 [card=88,autodetected] [ 45.886394] bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init] [ 45.943203] bttv1: osprey eeprom: card=89 name=Osprey 210/220/230 serial=3081860 [ 45.943209] bttv1: using tuner=-1 [ 45.943214] bttv1: i2c: checking for TDA9887 @ 0x86... not found [ 45.944303] bttv1: registered device video1 [ 45.944669] bttv1: registered device vbi1 [ 45.944695] bttv1: PLL: 28636363 => 35468950 .. ok also i halsa an osprey for capturing video from composition or svideo. [ 45.753340] tveeprom 0-0050: audio processor is None (idx 0): not looking good? i can see video perfectly with tvtime xawtv fail on me: xinerama 0: 1280x1024+0+0 xinerama 1: 1280x1024+1280+0 X Error of failed request: XF86DGANoDirectVideoMode -- tv card audio not working https://bugs.launchpad.net/bugs/29789 You received this bug notification because you are a member of Ubuntu Bugs, which is a direct subscriber. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
