Public bug reported:
Binary package hint: cpufrequtils
I have ThinkPad T60p with Core 2 Duo 2Gz CPU.
When the laptop wakes up after sleeping in standby mode, my CPU frequency gets
stuck in the lowest possible mode: 1Gz. I know that this is CPU frequency
scaling module who's doing that. I tried to change many different variables:
running on AC power vs battery, switching between governors (ondemand,
conservative) - nothing helps. It wakes up and does not scale from 1Gz. (I know
how to force CPU go up to 2Gz even with conservative governor - I run several
instances of glxgears).
Below is the output from cpufreq-info, as you can see it says
[I]"frequency should be within 1000 MHz and 1000 MHz"[/I]. It correctly
reports hardware max. limit of 2GHz, but [B]cpufreq thinks that the
upper allowed frequency limit is only 1Gz[/B]!!!
[CODE]cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006
Report errors and bugs to [EMAIL PROTECTED], please.
analyzing CPU 0:
driver: acpi-cpufreq
CPUs which need to switch frequency at the same time: 0 1
hardware limits: 1000 MHz - 2.00 GHz
available frequency steps: 2.00 GHz, 1.67 GHz, 1.33 GHz, 1000 MHz
available cpufreq governors: conservative, performance
current policy: frequency should be within 1000 MHz and 1000 MHz.
The governor "conservative" may decide which speed to use
within this range.
current CPU frequency is 1000 MHz (asserted by call to hardware).
analyzing CPU 1:
driver: acpi-cpufreq
CPUs which need to switch frequency at the same time: 0 1
hardware limits: 1000 MHz - 2.00 GHz
available frequency steps: 2.00 GHz, 1.67 GHz, 1.33 GHz, 1000 MHz
available cpufreq governors: conservative, performance
current policy: frequency should be within 1000 MHz and 1000 MHz.
The governor "conservative" may decide which speed to use
within this range.
current CPU frequency is 1000 MHz (asserted by call to hardware).
[/CODE]
If I reboot everything goes back to normal. CPU scales up and the output
above says "should be withtin 1000 MHz and 2 GHz".
I have been trying to fix it myself. For instance I added the following to
/etc/default/acpi-support (trying to reload CPU scaling kernel modules on
suspend/resume):
[CODE]MODULES="cpufreq_stats cpufreq_conservative acpi-cpufreq"[/CODE]
It did not help.
Then I tried
[CODE]sudo cpufreq-set -u 2000000
or
sudo cpufreq-set -u 2GHz[/CODE]
Those did not do anything either - CPU still could not get up to 2Gz.
Also I wet to /sys/devices/system/cpu and run these commands as root:
[CODE]echo 2000000 > cpu0/cpufreq/scaling_max_freq
echo 2000000 > cpu1/cpufreq/scaling_max_freq
[/CODE]
... and nothing happens. Those two files still say 1000000. Normally
(after reboot) they report 2000000 and I can write other values into
them. At this point I am not sure what else can I try. Obviously I
should update wakeup/resume scripts with some commands to bitch-slap cpu
frequency scaling module, but I cannot figure out what to do.
Here is my /etc/default/cpufrequtils
[CODE]ENABLE="true"
GOVERNOR="conservative"
MIN_SPEED=1000000
MAX_SPEED=2000000
[/CODE]
Here is my /etc/modules
[CODE]lp
cpufreq_stats
cpufreq_ondemand
cpufreq_conservative
cpufreq_powersave
acpi-cpufreq # this is what Core 2 Duo needs.
fuse
[/CODE]
This is very frustrating. I spent 5 hours last night trying to figure
this out...
** Affects: cpufrequtils (Ubuntu)
Importance: Undecided
Status: New
--
CPU frequency gets stuck at the lowest frequency after resume from suspend
(ThinkPad T60p)
https://bugs.launchpad.net/bugs/138465
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
