Public bug reported:
I'm attempting to install Kubuntu 7.10 Tribe 5 from the alternate
installation CD. On my system, it fails to detect my CD-ROM drives.
I have an onboard HPT374 (4 IDE ports, driven by the hpt366 module in
the installation system), to which I have connected two hard drives. I
also have an onboard VIA IDE controller, which has my optical drives
connected. The 4 IDE ports on the HPT374 appear to fill the kernel's IDE
table, preventing the VIA from registering; disabling the HPT allows the
CD drives to be detected at the expense of my hard drives.
I've tried to work around this by making the system load the via82cxxx
module first, then the hpt366 module (since I only need two of the four
ports to install), but I cannot work out how to do this. On my current
Gentoo Linux install, I get the following lspci and dmesg output:
$ sudo lspci -vvvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: d0000000-dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04)
Subsystem: Creative Labs SB Audigy 2 ZS (SB0350)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at a000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.1 Input device controller: Creative Labs SB Audigy Game Port (rev 04)
Subsystem: Creative Labs SB Audigy MIDI/Game Port
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at a400 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04)
(prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 16
Region 0: Memory at eb00a000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at eb000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:0a.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10
[OHCI])
Subsystem: ALi Corporation USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 22
Region 0: Memory at eb004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10
[OHCI])
Subsystem: ALi Corporation USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 17
Region 0: Memory at eb005000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10
[OHCI])
Subsystem: ALi Corporation USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 19
Region 0: Memory at eb006000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) (prog-if 20
[EHCI])
Subsystem: Unknown device 2020:8888
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at eb007000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture
(rev 02)
Subsystem: Askey Computer Corp. Unknown device 3002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 12
Region 0: Memory at eb008000 (32-bit, prefetchable) [size=4K]
00:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev
02)
Subsystem: Askey Computer Corp. Unknown device 3002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 12
Region 0: Memory at eb009000 (32-bit, prefetchable) [size=4K]
00:0e.0 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
Subsystem: Triones Technologies, Inc. Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at a800 [size=8]
Region 1: I/O ports at ac00 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at b400 [size=4]
Region 4: I/O ports at b800 [size=256]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.1 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
Subsystem: Triones Technologies, Inc. Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at c000 [size=4]
Region 2: I/O ports at c400 [size=8]
Region 3: I/O ports at c800 [size=4]
Region 4: I/O ports at cc00 [size=256]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20
[EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 21
Region 0: Memory at eb00b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 20
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at dc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237
AC97 Audio Controller (rev 50)
Subsystem: EPoX Computer Co., Ltd. Unknown device 3005
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 23
Region 0: I/O ports at e000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: EPoX Computer Co., Ltd. VT6103
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at eb00c000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R200 QL [Radeon
8500 LE] (prog-if 00 [VGA])
Subsystem: Hercules Radeon 8500 [3D Prophet 8500 128Mb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at e8000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW-
Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
$ dmesg
[ 0.000000] Linux version 2.6.21-gentoo-r1 ([EMAIL PROTECTED]) (gcc version
4.1.2 (Gentoo 4.1.2)) #1 Sat May 19 11:56:30 BST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009e800
end: 000000000009e800 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009e800 size: 0000000000001800
end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000
end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003fef0000
end: 000000003fff0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000003fff0000 size: 0000000000003000
end: 000000003fff3000 type: 4
[ 0.000000] copy_e820_map() start: 000000003fff3000 size: 000000000000d000
end: 0000000040000000 type: 3
[ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000001000
end: 00000000fec01000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000
end: 00000000fee01000 type: 2
[ 0.000000] copy_e820_map() start: 00000000ffff0000 size: 0000000000010000
end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 1023MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f5e30
[ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 262128
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262128
[ 0.000000] On node 0 totalpages: 262128
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 2015 pages used for memmap
[ 0.000000] Normal zone: 256017 pages, LIFO batch:31
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP 000F7840, 0014 (r0 VIA694)
[ 0.000000] ACPI: RSDT 3FFF3000, 002C (r1 VIA694 AWRDACPI 42302E31 AWRD
0)
[ 0.000000] ACPI: FACP 3FFF3040, 0074 (r1 VIA694 AWRDACPI 42302E31 AWRD
0)
[ 0.000000] ACPI: DSDT 3FFF30C0, 411A (r1 VIA694 AWRDACPI 1000 MSFT
100000C)
[ 0.000000] ACPI: FACS 3FFF0000, 0040
[ 0.000000] ACPI: APIC 3FFF7200, 005A (r1 VIA694 AWRDACPI 42302E31 AWRD
0)
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap:
40000000:bec00000)
[ 0.000000] Built 1 zonelists. Total pages: 260081
[ 0.000000] Kernel command line: root=/dev/evms/root ro ramdisk_size=8192
elevator=cfq libata.fua=1
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] CPU 0 irqstacks, hard=b04d6000 soft=b04d5000
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1470.077 MHz processor.
[ 53.999308] Console: colour VGA+ 80x25
[ 54.003706] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 54.005419] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 54.040929] Memory: 1031256k/1048512k available (2569k kernel code, 16612k
reserved, 1132k data, 196k init, 0k highmem)
[ 54.041030] virtual kernel memory layout:
[ 54.041032] fixmap : 0xfffb7000 - 0xfffff000 ( 288 kB)
[ 54.041034] vmalloc : 0xf0800000 - 0xfffb5000 ( 247 MB)
[ 54.041036] lowmem : 0xb0000000 - 0xefff0000 (1023 MB)
[ 54.041038] .init : 0xb049f000 - 0xb04d0000 ( 196 kB)
[ 54.041040] .data : 0xb03827fb - 0xb049d810 (1132 kB)
[ 54.041041] .text : 0xb0100000 - 0xb03827fb (2569 kB)
[ 54.041443] Checking if this processor honours the WP bit even in supervisor
mode... Ok.
[ 54.101597] Calibrating delay using timer specific routine.. 2940.78
BogoMIPS (lpj=1470392)
[ 54.101758] Mount-cache hash table entries: 512
[ 54.101949] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000
00000000 00000000 00000000 00000000
[ 54.101960] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 54.102023] CPU: L2 Cache: 256K (64 bytes/line)
[ 54.102082] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420
00000000 00000000 00000000
[ 54.102090] Intel machine check architecture supported.
[ 54.102150] Intel machine check reporting enabled on CPU#0.
[ 54.102213] Compat vDSO mapped to ffffe000.
[ 54.102279] CPU: AMD Athlon(tm) XP 1700+ stepping 01
[ 54.102400] Checking 'hlt' instruction... OK.
[ 54.105747] ACPI: Core revision 20070126
[ 54.120176] ENABLING IO-APIC IRQs
[ 54.120421] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 54.231671] NET: Registered protocol family 16
[ 54.231837] ACPI: bus type pci registered
[ 54.233719] PCI: PCI BIOS revision 2.10 entry at 0xfb3d0, last bus=1
[ 54.233780] PCI: Using configuration type 1
[ 54.233838] Setting up standard PCI resources
[ 54.248744] ACPI: Interpreter enabled
[ 54.248809] ACPI: (supports S0 S1 S3 S4 S5)
[ 54.249061] ACPI: Using IOAPIC for interrupt routing
[ 54.255567] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 54.255643] PCI: Probing PCI hardware (bus 00)
[ 54.256472] PCI quirk: region 4000-407f claimed by vt8235 PM
[ 54.256535] PCI quirk: region 5000-500f claimed by vt8235 SMB
[ 54.256820] Boot video device is 0000:01:00.0
[ 54.256868] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 54.301718] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14
15)
[ 54.302382] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14
15)
[ 54.303049] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 *12 14
15)
[ 54.303717] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14
15)
[ 54.304378] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
[ 54.304752] ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
[ 54.305122] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
[ 54.305475] ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0
[ 54.305750] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 54.305821] pnp: PnP ACPI init
[ 54.309281] pnp: PnP ACPI: found 11 devices
[ 54.309491] SCSI subsystem initialized
[ 54.309578] libata version 2.20 loaded.
[ 54.309659] usbcore: registered new interface driver usbfs
[ 54.309760] usbcore: registered new interface driver hub
[ 54.309855] usbcore: registered new device driver usb
[ 54.309988] PCI: Using ACPI for IRQ routing
[ 54.310049] PCI: If a device doesn't work, try "pci=routeirq". If it helps,
post a report
[ 54.345243] Bluetooth: Core ver 2.11
[ 54.345347] NET: Registered protocol family 31
[ 54.345409] Bluetooth: HCI device and connection manager initialized
[ 54.345473] Bluetooth: HCI socket layer initialized
[ 54.346003] ACPI: PCI Interrupt 0000:00:09.2[B] -> GSI 18 (level, low) ->
IRQ 16
[ 54.346365] Time: tsc clocksource has been installed.
[ 54.396449] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
MMIO=[eb00a000-eb00a7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 54.426625] PCI: Bridge: 0000:00:01.0
[ 54.426684] IO window: 9000-9fff
[ 54.426744] MEM window: e8000000-e9ffffff
[ 54.426804] PREFETCH window: d0000000-dfffffff
[ 54.426875] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 54.426911] NET: Registered protocol family 2
[ 54.435307] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 54.435639] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[ 54.437876] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 54.438418] TCP: Hash tables configured (established 131072 bind 65536)
[ 54.438481] TCP reno registered
[ 54.441437] checking if image is initramfs...it isn't (no cpio magic); looks
like an initrd
[ 54.626350] Freeing initrd memory: 3096k freed
[ 54.626666] Machine check exception polling timer started.
[ 54.627088] Total HugeTLB memory allocated, 0
[ 54.627282] Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
[ 54.627596] io scheduler noop registered
[ 54.627661] io scheduler cfq registered (default)
[ 54.686993] Real Time Clock Driver v1.12ac
[ 54.687065] Linux agpgart interface v0.102 (c) Dave Jones
[ 54.687170] agpgart: Detected VIA KT266/KY266x/KT333 chipset
[ 54.695921] agpgart: AGP aperture is 128M @ 0xe0000000
[ 54.696046] [drm] Initialized drm 1.1.0 20060810
[ 54.696143] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) ->
IRQ 17
[ 54.696348] [drm] Initialized radeon 1.25.0 20060524 on minor 0
[ 54.696421] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds,
margin is 60 seconds).
[ 54.696507] Hangcheck: Using get_cycles().
[ 54.696703] input: Power Button (FF) as /class/input/input0
[ 54.696771] ACPI: Power Button (FF) [PWRF]
[ 54.696925] input: Power Button (CM) as /class/input/input1
[ 54.696999] ACPI: Power Button (CM) [PWRB]
[ 54.697140] input: Sleep Button (CM) as /class/input/input2
[ 54.697207] ACPI: Sleep Button (CM) [SLPB]
[ 54.697344] ACPI: Fan [FAN] (on)
[ 54.697530] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 54.698771] ACPI: Thermal Zone [THRM] (48 C)
[ 54.698847] isapnp: Scanning for PnP cards...
[ 54.927319] Switched to high resolution mode on CPU 0
[ 55.055154] isapnp: No Plug & Play device found
[ 55.055214] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
disabled
[ 55.055415] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 55.055783] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 55.056587] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 55.057030] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 55.057581] parport: PnPBIOS parport detected.
[ 55.057732] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 0.949000] Time: acpi_pm clocksource has been installed.
[ 0.979000] RAMDISK driver initialized: 1 RAM disks of 8192K size 1024
blocksize
[ 0.979000] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 0.979000] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 0.979000] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
[ 0.979000] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[ 0.979000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23
(level, low) -> IRQ 18
[ 0.984000] eth0: VIA Rhine II at 0xeb00c000, 00:04:61:42:f5:92, IRQ 18.
[ 0.985000] eth0: MII PHY found at address 1, status 0x786d advertising 05e1
Link 45e1.
[ 0.985000] pata_hpt37x: BIOS has not set timing clocks.
[ 0.987000] hpt37x: HPT374: Bus clock 33MHz.
[ 0.987000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) ->
IRQ 19
[ 0.987000] ata1: PATA max UDMA/133 cmd 0x0001a800 ctl 0x0001ac02 bmdma
0x0001b800 irq 19
[ 0.987000] ata2: PATA max UDMA/133 cmd 0x0001b000 ctl 0x0001b402 bmdma
0x0001b808 irq 19
[ 0.988000] scsi0 : pata_hpt37x
[ 1.142000] ata1.00: ATA-5: WDC WD1200JB-00CRA1, 17.07W17, max UDMA/100
[ 1.142000] ata1.00: 234441648 sectors, multi 16: LBA
[ 1.142000] Find mode for 12 reports A81F442
[ 1.142000] Find mode for DMA 69 reports 12848242
[ 1.162000] ata1.00: configured for UDMA/100
[ 1.162000] scsi1 : pata_hpt37x
[ 1.316000] ata2.00: ATA-6: WDC WD1200JB-00GVA0, 08.02D08, max UDMA/100
[ 1.316000] ata2.00: 234441648 sectors, multi 16: LBA48
[ 1.316000] Find mode for 12 reports A81F442
[ 1.316000] Find mode for DMA 69 reports 12848242
[ 1.336000] ata2.00: configured for UDMA/100
[ 1.336000] scsi 0:0:0:0: Direct-Access ATA WDC WD1200JB-00C 17.0
PQ: 0 ANSI: 5
[ 1.336000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 1.336000] sda: Write Protect is off
[ 1.336000] sda: Mode Sense: 00 3a 00 00
[ 1.336000] SCSI device sda: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.336000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 1.336000] sda: Write Protect is off
[ 1.337000] sda: Mode Sense: 00 3a 00 00
[ 1.337000] SCSI device sda: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.337000] sda: sda1 sda2 sda3
[ 1.357000] sd 0:0:0:0: Attached scsi disk sda
[ 1.357000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.357000] scsi 1:0:0:0: Direct-Access ATA WDC WD1200JB-00G 08.0
PQ: 0 ANSI: 5
[ 1.358000] SCSI device sdb: 234441648 512-byte hdwr sectors (120034 MB)
[ 1.358000] sdb: Write Protect is off
[ 1.358000] sdb: Mode Sense: 00 3a 00 00
[ 1.358000] SCSI device sdb: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.358000] SCSI device sdb: 234441648 512-byte hdwr sectors (120034 MB)
[ 1.358000] sdb: Write Protect is off
[ 1.358000] sdb: Mode Sense: 00 3a 00 00
[ 1.358000] SCSI device sdb: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.358000] sdb: sdb1 sdb2 sdb3
[ 1.365000] sd 1:0:0:0: Attached scsi disk sdb
[ 1.365000] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.366000] pata_hpt37x: BIOS has not set timing clocks.
[ 1.368000] hpt37x: HPT374: Bus clock 33MHz.
[ 1.368000] ACPI: PCI Interrupt 0000:00:0e.1[A] -> GSI 17 (level, low) ->
IRQ 19
[ 1.368000] ata3: PATA max UDMA/133 cmd 0x0001bc00 ctl 0x0001c002 bmdma
0x0001cc00 irq 19
[ 1.368000] ata4: PATA max UDMA/133 cmd 0x0001c400 ctl 0x0001c802 bmdma
0x0001cc08 irq 19
[ 1.368000] scsi2 : pata_hpt37x
[ 1.517000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c01510f6043]
[ 1.519000] ATA: abnormal status 0x8 on port 0x0001bc07
[ 1.530000] scsi3 : pata_hpt37x
[ 1.681000] ATA: abnormal status 0x8 on port 0x0001c407
[ 1.692000] pata_via 0000:00:11.1: version 0.2.1
[ 1.692000] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[ 1.692000] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 1.692000] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20
(level, low) -> IRQ 20
[ 1.693000] ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma
0x0001dc00 irq 14
[ 1.693000] ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma
0x0001dc08 irq 15
[ 1.693000] scsi4 : pata_via
[ 1.998000] ata5.00: ATAPI, max UDMA/33
[ 2.155000] ata5.00: configured for UDMA/33
[ 2.155000] scsi5 : pata_via
[ 2.460000] ata6.00: ATAPI, max UDMA/33
[ 2.633000] ata6.00: configured for UDMA/33
[ 2.634000] scsi 4:0:0:0: CD-ROM ATAPI DVD RW 8XMax 130D
PQ: 0 ANSI: 5
[ 2.634000] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 2.635000] Uniform CD-ROM driver Revision: 3.20
[ 2.635000] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 2.635000] sr 4:0:0:0: Attached scsi generic sg2 type 5
[ 2.639000] scsi 5:0:0:0: CD-ROM LITE-ON LTR-40125S XSU1
PQ: 0 ANSI: 5
[ 2.714000] sr1: scsi3-mmc drive: 93x/48x writer cd/rw xa/form2 cdda tray
[ 2.714000] sr 5:0:0:0: Attached scsi CD-ROM sr1
[ 2.714000] sr 5:0:0:0: Attached scsi generic sg3 type 5
[ 2.714000] ACPI: PCI Interrupt 0000:00:0a.3[A] -> GSI 18 (level, low) ->
IRQ 16
[ 2.714000] ehci_hcd 0000:00:0a.3: EHCI Host Controller
[ 2.714000] ehci_hcd 0000:00:0a.3: new USB bus registered, assigned bus
number 1
[ 2.714000] ehci_hcd 0000:00:0a.3: debug port 1
[ 2.736000] ehci_hcd 0000:00:0a.3: irq 16, io mem 0xeb007000
[ 2.736000] ehci_hcd 0000:00:0a.3: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
[ 2.736000] usb usb1: configuration #1 chosen from 1 choice
[ 2.736000] hub 1-0:1.0: USB hub found
[ 2.736000] hub 1-0:1.0: 6 ports detected
[ 2.837000] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
[ 2.837000] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[ 2.837000] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] -> GSI 21
(level, low) -> IRQ 21
[ 2.837000] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 2.837000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus
number 2
[ 2.838000] ehci_hcd 0000:00:10.3: irq 21, io mem 0xeb00b000
[ 2.838000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
[ 2.838000] usb usb2: configuration #1 chosen from 1 choice
[ 2.838000] hub 2-0:1.0: USB hub found
[ 2.838000] hub 2-0:1.0: 6 ports detected
[ 2.939000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI)
Driver
[ 2.939000] ACPI: PCI Interrupt 0000:00:0a.0[B] -> GSI 19 (level, low) ->
IRQ 22
[ 2.939000] ohci_hcd 0000:00:0a.0: OHCI Host Controller
[ 2.939000] ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus
number 3
[ 2.939000] ohci_hcd 0000:00:0a.0: irq 22, io mem 0xeb004000
[ 2.992000] usb usb3: configuration #1 chosen from 1 choice
[ 2.992000] hub 3-0:1.0: USB hub found
[ 2.992000] hub 3-0:1.0: 2 ports detected
[ 3.093000] ACPI: PCI Interrupt 0000:00:0a.1[C] -> GSI 16 (level, low) ->
IRQ 17
[ 3.093000] ohci_hcd 0000:00:0a.1: OHCI Host Controller
[ 3.093000] ohci_hcd 0000:00:0a.1: new USB bus registered, assigned bus
number 4
[ 3.093000] ohci_hcd 0000:00:0a.1: irq 17, io mem 0xeb005000
[ 3.146000] usb usb4: configuration #1 chosen from 1 choice
[ 3.146000] hub 4-0:1.0: USB hub found
[ 3.146000] hub 4-0:1.0: 2 ports detected
[ 3.247000] ACPI: PCI Interrupt 0000:00:0a.2[D] -> GSI 17 (level, low) ->
IRQ 19
[ 3.247000] ohci_hcd 0000:00:0a.2: OHCI Host Controller
[ 3.247000] ohci_hcd 0000:00:0a.2: new USB bus registered, assigned bus
number 5
[ 3.247000] ohci_hcd 0000:00:0a.2: irq 19, io mem 0xeb006000
[ 3.300000] usb usb5: configuration #1 chosen from 1 choice
[ 3.300000] hub 5-0:1.0: USB hub found
[ 3.300000] hub 5-0:1.0: 2 ports detected
[ 3.401000] USB Universal Host Controller Interface driver v3.0
[ 3.401000] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21
(level, low) -> IRQ 21
[ 3.401000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 3.401000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus
number 6
[ 3.401000] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000d000
[ 3.401000] usb usb6: configuration #1 chosen from 1 choice
[ 3.401000] hub 6-0:1.0: USB hub found
[ 3.402000] hub 6-0:1.0: 2 ports detected
[ 3.503000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKB] -> GSI 21
(level, low) -> IRQ 21
[ 3.503000] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 3.503000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus
number 7
[ 3.503000] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d400
[ 3.503000] usb usb7: configuration #1 chosen from 1 choice
[ 3.503000] hub 7-0:1.0: USB hub found
[ 3.503000] hub 7-0:1.0: 2 ports detected
[ 3.604000] ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKB] -> GSI 21
(level, low) -> IRQ 21
[ 3.604000] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 3.604000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus
number 8
[ 3.604000] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d800
[ 3.604000] usb usb8: configuration #1 chosen from 1 choice
[ 3.604000] hub 8-0:1.0: USB hub found
[ 3.604000] hub 8-0:1.0: 2 ports detected
[ 3.813000] usb 6-2: new low speed USB device using uhci_hcd and address 2
[ 3.977000] usb 6-2: configuration #1 chosen from 1 choice
[ 4.396000] usbcore: registered new interface driver cdc_acm
[ 4.396000] drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model
driver for USB modems and ISDN adapters
[ 4.396000] usbcore: registered new interface driver usblp
[ 4.396000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 4.396000] Initializing USB Mass Storage driver...
[ 4.396000] usbcore: registered new interface driver usb-storage
[ 4.396000] USB Mass Storage support registered.
[ 4.410000] input: Logitech USB Receiver as /class/input/input3
[ 4.410000] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on
usb-0000:00:10.0-2
[ 4.440000] input: Logitech USB Receiver as /class/input/input4
[ 4.440000] input: USB HID v1.10 Mouse [Logitech USB Receiver] on
usb-0000:00:10.0-2
[ 4.441000] usbcore: registered new interface driver usbhid
[ 4.441000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 4.441000] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 4.441000] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 4.442000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.442000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.442000] mice: PS/2 mouse device common for all mice
[ 4.460000] input: AT Translated Set 2 keyboard as /class/input/input5
[ 4.490000] md: raid1 personality registered for level 1
[ 4.490000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
[EMAIL PROTECTED]
[ 4.490000] Bluetooth: HCI USB driver ver 2.9
[ 4.490000] usbcore: registered new interface driver hci_usb
[ 4.490000] Bluetooth: Broadcom Blutonium firmware driver ver 1.1
[ 4.490000] usbcore: registered new interface driver bcm203x
[ 4.490000] Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed
Mar 14 07:25:50 2007 UTC).
[ 4.491000] ALSA device list:
[ 4.491000] No soundcards found.
[ 4.491000] TCP cubic registered
[ 4.491000] NET: Registered protocol family 1
[ 4.491000] NET: Registered protocol family 10
[ 4.491000] NET: Registered protocol family 17
[ 4.491000] Bluetooth: L2CAP ver 2.8
[ 4.491000] Bluetooth: L2CAP socket layer initialized
[ 4.491000] Bluetooth: RFCOMM socket layer initialized
[ 4.491000] Bluetooth: RFCOMM TTY layer initialized
[ 4.491000] Bluetooth: RFCOMM ver 1.8
[ 4.491000] Using IPI Shortcut mode
[ 4.593000] md: Autodetecting RAID arrays.
[ 4.593000] md: autorun ...
[ 4.593000] md: ... autorun DONE.
[ 4.593000] RAMDISK: Compressed image found at block 0
[ 4.789000] VFS: Mounted root (ext2 filesystem).
[ 9.737000] md: bind<dm-0>
[ 9.737000] md: bind<dm-1>
[ 9.738000] raid1: raid set md0 active with 2 out of 2 mirrors
[ 9.738000] md0: bitmap initialized from disk: read 1/1 pages, set 0 bits,
status: 0
[ 9.738000] created bitmap (12 pages) for device md0
[ 9.761000] md: bind<dm-3>
[ 9.761000] md: bind<dm-4>
[ 9.762000] raid1: raid set md1 active with 2 out of 2 mirrors
[ 9.771000] md1: bitmap initialized from disk: read 14/14 pages, set 43
bits, status: 0
[ 9.771000] created bitmap (220 pages) for device md1
[ 9.860000] kjournald starting. Commit interval 5 seconds
[ 9.860000] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.080000] Freeing unused kernel memory: 196k freed
[ 12.313000] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) ->
IRQ 19
[ 12.315000] Installing spdif_bug patch: Audigy 2 ZS [SB0350]
[ 12.785000] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
[ 12.785000] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 12.785000] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22
(level, low) -> IRQ 23
[ 12.785000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 20.138000] EXT3 FS on dm-10, internal journal
[ 26.743000] kjournald starting. Commit interval 5 seconds
[ 26.779000] EXT3 FS on dm-8, internal journal
[ 26.779000] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.809000] kjournald starting. Commit interval 5 seconds
[ 26.840000] EXT3 FS on dm-18, internal journal
[ 26.840000] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.882000] kjournald starting. Commit interval 5 seconds
[ 26.915000] EXT3 FS on dm-20, internal journal
[ 26.915000] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.927000] kjournald starting. Commit interval 5 seconds
[ 26.991000] EXT3 FS on dm-16, internal journal
[ 26.991000] EXT3-fs: mounted filesystem with ordered data mode.
[ 27.020000] kjournald starting. Commit interval 5 seconds
[ 27.056000] EXT3 FS on dm-6, internal journal
[ 27.056000] EXT3-fs: mounted filesystem with ordered data mode.
[ 27.216000] Adding 1953492k swap on /dev/evms/swap0. Priority:-1 extents:1
across:1953492k
[ 27.227000] Adding 1953492k swap on /dev/evms/swap1. Priority:-2 extents:1
across:1953492k
[ 2948.409000] mtrr: no MTRR for d0000000,8000000 found
[ 2949.774000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 2949.774000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 2949.774000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 2950.059000] [drm] Setting GART location based on new memory map
[ 2950.059000] [drm] Loading R200 Microcode
I'm going to attempt to use debootstrap to install Kubuntu instead; I
believe this bug could be fixed by either switching to libata for PATA
drivers, or changing IDE_MAX_HWIFS to at least 6 (the default is 4, the
limit is 10).
** Affects: ubuntu
Importance: Undecided
Status: New
--
[gutsy tribe 5] Fails to handle systems with too many IDE interfaces
https://bugs.launchpad.net/bugs/137619
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
