I never got my Feisty Fawn CD to boot for the same reasons as listed
above. I got gentoo onto the machine and lspci is lspci and here is the
output. Its too bad, because gentoo is just too much work. Oh, yeah,
here's the kernel info.
Linux localhost 2.6.22-gentoo-r2 #10 SMP PREEMPT Mon Aug 13 08:44:04
Local time zone must be set- i686 Intel(R) Core(TM)2 Duo CPU T7500
@ 2.20GHz GenuineIntel GNU/Linux
00:00.0 0600: 8086:2a00 (rev 0c)
Subsystem: 1028:01fe
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 0604: 8086:2a01 (rev 0c) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fa000000-feafffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] Subsystem: 1028:01fe
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise-
Slot: Number 1, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)
00:1a.0 0c03: 8086:2834 (rev 02) (prog-if 00 [UHCI])
Subsystem: 1028:01fe
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f20 [size=32]
00:1a.1 0c03: 8086:2835 (rev 02) (prog-if 00 [UHCI])
Subsystem: 1028:01fe
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f00 [size=32]
00:1a.7 0c03: 8086:283a (rev 02) (prog-if 20 [EHCI])
Subsystem: 1028:01fe
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1b.0 0403: 8086:284b (rev 02)
Subsystem: 1028:01fe
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 21
Region 0: Memory at febfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00:1c.0 0604: 8086:283f (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 2, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: 1028:01fe
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.1 0604: 8086:2841 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
Memory behind bridge: f9f00000-f9ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: 1028:01fe
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.3 0604: 8086:2845 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0e, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f9c00000-f9efffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 5, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: 1028:01fe
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.5 0604: 8086:2849 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Memory behind bridge: f9b00000-f9bfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: 1028:01fe
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1d.0 0c03: 8086:2830 (rev 02) (prog-if 00 [UHCI])
Subsystem: 1028:01fe
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f80 [size=32]
00:1d.1 0c03: 8086:2831 (rev 02) (prog-if 00 [UHCI])
Subsystem: 1028:01fe
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f60 [size=32]
00:1d.2 0c03: 8086:2832 (rev 02) (prog-if 00 [UHCI])
Subsystem: 1028:01fe
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 6f40 [size=32]
00:1d.7 0c03: 8086:2836 (rev 02) (prog-if 20 [EHCI])
Subsystem: 1028:01fe
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 0604: 8086:2448 (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=04, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f9a00000-f9afffff
Prefetchable memory behind bridge: 0000000088000000-000000008bffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: 1028:01fe
00:1f.0 0601: 8086:2815 (rev 02)
Subsystem: 1028:01fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.1 0101: 8086:2850 (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: 1028:01fe
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 6fa0 [size=16]
00:1f.2 0101: 8086:2828 (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: 1028:01fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 6eb0 [size=8]
Region 1: I/O ports at 6eb8 [size=4]
Region 2: I/O ports at 6ec0 [size=8]
Region 3: I/O ports at 6ec8 [size=4]
Region 4: I/O ports at 6ee0 [size=16]
Region 5: I/O ports at eff0 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 0c05: 8086:283e (rev 02)
Subsystem: 1028:01fe
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at febfbf00 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 10c0 [size=32]
01:00.0 0300: 10de:042b (rev a1) (prog-if 00 [VGA])
Subsystem: 1028:01fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at df00 [size=128]
[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <512ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM L0s L1 Enabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting
Capabilities: [600] Unknown (11)
03:01.0 0607: 1217:7135 (rev 21)
Subsystem: 1028:01fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f9a00000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
Memory window 0: 88000000-8bfff000 (prefetchable)
Memory window 1: 8c000000-8ffff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite-
16-bit legacy interface ports at 0001
03:01.4 0c00: 1217:00f7 (rev 02) (prog-if 10 [OHCI])
Subsystem: 1028:01fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f9aff000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f9afe800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
09:00.0 0200: 14e4:1673 (rev 02)
Subsystem: 1028:01fe
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 223
Region 0: Memory at f9bf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Vendor Specific Information
Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable+
Address: 00000000fee0200c Data: 41d9
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM L0s Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [160] Device Serial Number c8-e9-81-fe-ff-b9-19-00
Capabilities: [16c] Power Budgeting
0c:00.0 0280: 8086:4222 (rev 02)
Subsystem: 8086:1020
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f9fff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number f8-99-71-ff-ff-77-1b-00
--
install fails: busybox (initramfs): can't access tty: (/dev/sda trouble?)
https://bugs.launchpad.net/bugs/129817
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
