Public bug reported:
With ubuntu gutsy, the network manager detects both my ethernet card and my
wifi card. When I plug the ethernet in, it configures the inteface correctly,
but if I ask to connect to my wifi (unencrypted), it just shows the
"connecting" animation for a few minutes and then fail silently and show the
"not connected" icon.
If I manually configure the network, the wifi works fine (but only after a
restart. If I don't restart the computer, I have to do "ifup eth1")
And it was working fine with edgy (excepted sometimes when resuming after a
suspend)
My ifconfig (once connected)
eth0 Link encap:Ethernet HWaddr 00:0F:B0:D2:B0:77
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22 Base address:0x8000
eth1 Link encap:Ethernet HWaddr 00:19:D2:97:10:11
inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::219:d2ff:fe97:1011/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16045 errors:7 dropped:388 overruns:0 frame:0
TX packets:8267 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:21654431 (20.6 MB) TX bytes:564308 (551.0 KB)
Interrupt:17 Base address:0x4000 Memory:d2000000-d2000fff
eth0:avah Link encap:Ethernet HWaddr 00:0F:B0:D2:B0:77
inet addr:169.254.8.249 Bcast:169.254.255.255
Mask:255.255.0.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
Interrupt:22 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:151 errors:0 dropped:0 overruns:0 frame:0
TX packets:151 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14105 (13.7 KB) TX bytes:14105 (13.7 KB)
My iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11g ESSID:"linksys-g"
Mode:Managed Frequency:2.462 GHz Access Point:
00:0F:66:1A:F0:53
Bit Rate:54 Mb/s Tx-Power:15 dBm
Retry limit:15 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=71/100 Signal level=-63 dBm Noise level=-63 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:398 Missed beacon:0
And my lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 2 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2
EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family)
Serial ATA Storage Controller IDE (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller
(rev 02)
01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 110M /
GeForce Go 7300 (rev a1)
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
Network Connection (rev 02)
05:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
05:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller
(rev 01)
05:06.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
05:06.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
05:06.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
05:06.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 0a)
05:06.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev
05)
** Affects: network-manager (Ubuntu)
Importance: Undecided
Status: New
** Description changed:
- With ubuntu gutsy, the network manager detects both my ethernet card and
- my wifi card. When I plug the ethernet in, it configures the inteface
- correctly, but if I ask to connect to my wifi (unencrypted), it just
- shows the "connecting" animation for a few minutes and then fail
- silently and show the "not connected" icon.
+ With ubuntu gutsy, the network manager detects both my ethernet card and my
wifi card. When I plug the ethernet in, it configures the inteface correctly,
but if I ask to connect to my wifi (unencrypted), it just shows the
"connecting" animation for a few minutes and then fail silently and show the
"not connected" icon.
+ If I manually configure the network, the wifi works fine (but only after a
restart. If I don't restart the computer, I have to do "ifup eth1")
My ifconfig (once connected)
eth0 Link encap:Ethernet HWaddr 00:0F:B0:D2:B0:77
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22 Base address:0x8000
eth1 Link encap:Ethernet HWaddr 00:19:D2:97:10:11
inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::219:d2ff:fe97:1011/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16045 errors:7 dropped:388 overruns:0 frame:0
TX packets:8267 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:21654431 (20.6 MB) TX bytes:564308 (551.0 KB)
Interrupt:17 Base address:0x4000 Memory:d2000000-d2000fff
eth0:avah Link encap:Ethernet HWaddr 00:0F:B0:D2:B0:77
inet addr:169.254.8.249 Bcast:169.254.255.255
Mask:255.255.0.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
Interrupt:22 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:151 errors:0 dropped:0 overruns:0 frame:0
TX packets:151 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14105 (13.7 KB) TX bytes:14105 (13.7 KB)
My iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11g ESSID:"linksys-g"
Mode:Managed Frequency:2.462 GHz Access Point:
00:0F:66:1A:F0:53
Bit Rate:54 Mb/s Tx-Power:15 dBm
Retry limit:15 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=71/100 Signal level=-63 dBm Noise level=-63 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:398 Missed beacon:0
And my lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 2 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2
EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family)
Serial ATA Storage Controller IDE (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller
(rev 02)
01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 110M /
GeForce Go 7300 (rev a1)
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
Network Connection (rev 02)
05:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
05:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller
(rev 01)
05:06.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
05:06.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
05:06.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
05:06.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 0a)
05:06.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev
05)
** Description changed:
With ubuntu gutsy, the network manager detects both my ethernet card and my
wifi card. When I plug the ethernet in, it configures the inteface correctly,
but if I ask to connect to my wifi (unencrypted), it just shows the
"connecting" animation for a few minutes and then fail silently and show the
"not connected" icon.
If I manually configure the network, the wifi works fine (but only after a
restart. If I don't restart the computer, I have to do "ifup eth1")
+ And it was working fine with edgy (excepted sometimes when resuming after a
suspend)
My ifconfig (once connected)
eth0 Link encap:Ethernet HWaddr 00:0F:B0:D2:B0:77
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22 Base address:0x8000
eth1 Link encap:Ethernet HWaddr 00:19:D2:97:10:11
inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::219:d2ff:fe97:1011/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16045 errors:7 dropped:388 overruns:0 frame:0
TX packets:8267 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:21654431 (20.6 MB) TX bytes:564308 (551.0 KB)
Interrupt:17 Base address:0x4000 Memory:d2000000-d2000fff
eth0:avah Link encap:Ethernet HWaddr 00:0F:B0:D2:B0:77
inet addr:169.254.8.249 Bcast:169.254.255.255
Mask:255.255.0.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
Interrupt:22 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:151 errors:0 dropped:0 overruns:0 frame:0
TX packets:151 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14105 (13.7 KB) TX bytes:14105 (13.7 KB)
My iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11g ESSID:"linksys-g"
Mode:Managed Frequency:2.462 GHz Access Point:
00:0F:66:1A:F0:53
Bit Rate:54 Mb/s Tx-Power:15 dBm
Retry limit:15 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=71/100 Signal level=-63 dBm Noise level=-63 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:398 Missed beacon:0
And my lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 2 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2
EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family)
Serial ATA Storage Controller IDE (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller
(rev 02)
01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 110M /
GeForce Go 7300 (rev a1)
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
Network Connection (rev 02)
05:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
05:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller
(rev 01)
05:06.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
05:06.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
05:06.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
05:06.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 0a)
05:06.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev
05)
--
[gutsy] detects wifi card and networks but can't connect
https://bugs.launchpad.net/bugs/130290
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
