apport information
** Tags added: apport-collected precise staging
** Description changed:
Hot plugging USB3.0 PCI Express card not possible
Hot plugging USB devices in this Card is also not possible
Only way to access the card and USB device: is powering on with PCI card AND
USB devices connected.
reconnect devices after this is not possible.
Configuration:
- Ubuntu 12.04 x64 (problem was also on older versions)
- Lenovo T520
- PCI USB3.0 Express Card BC618, NEC uPD720200
More info:
Powering ON with USB3 express card AND USB3 HD connected:
PCI 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #2 (rev 04)
USB Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller
Device 005: ID 04f2:b217 Chicony Electronics Co., Ltd
Device 006: ID 046d:c05f Logitech, Inc.
PCI 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #1 (rev 04)
USB Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Device 003: ID 05ac:1297 Apple, Inc. iPhone 4
PCI 05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller
(rev 04)
USB Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
PCI 05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller
(rev 04)
USB Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device 002: ID 1058:1042 Western Digital Technologies, Inc.
# lspci -vs 0000:05:00.0
05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller
(rev 04) (prog-if 30 [XHCI])
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at f1d00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Capabilities: [90] MSI-X: Enable+ Count=8 Masked-
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150] Latency Tolerance Reporting
Kernel driver in use: xhci_hcd
Re-Plugging the drive but olso other USB products, are not recognized
in kern.log:
May 31 09:54:48 roland kernel: [ 1441.460174] hub 3-0:1.0: hub_port_status
failed (err = -19)
May 31 09:54:48 roland kernel: [ 1441.460244] hub 3-0:1.0: hub_port_status
failed (err = -19)
May 31 09:54:49 roland kernel: [ 1442.066711] hub 4-0:1.0: hub_port_status
failed (err = -19)
May 31 09:54:49 roland kernel: [ 1442.066773] hub 4-0:1.0: hub_port_status
failed (err = -19)
May 31 09:55:02 roland kernel: [ 1455.659879] hub 3-0:1.0: hub_port_status
failed (err = -19)
May 31 09:55:02 roland kernel: [ 1455.659938] hub 3-0:1.0: hub_port_status
failed (err = -19)
May 31 09:55:03 roland kernel: [ 1456.250534] hub 4-0:1.0: hub_port_status
failed (err = -19)
May 31 09:55:03 roland kernel: [ 1456.250595] hub 4-0:1.0: hub_port_status
failed (err = -19)
May 31 09:55:05 roland kernel: [ 1458.940363] hub 4-0:1.0: hub_port_status
failed (err = -19)
May 31 09:55:05 roland kernel: [ 1458.940429] hub 4-0:1.0: hub_port_status
failed (err = -19)
# lspci -vvs 0000:05:00.0
05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller
(rev 04) (prog-if 30 [XHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop+ ParErr+
Stepping+ SERR+ FastB2B+ DisINTx+
Status: Cap+ 66MHz+ UDF+ FastB2B+ ParErr+ DEVSEL=?? >TAbort+ <TAbort+
<MAbort+ >SERR+ <PERR+ INTx+
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f1d00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0
<4us, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: xhci_hcd
Plugging out the USB3 Express card:
no messages in kern.log !!
# lspci -vvs 0000:05:00.0
05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller
(rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: xhci_hcd
Plugging back in the USB3 Express card:
no messages in kern.log !!
Still not recognizing any USB insertions.
# lspci -vvs 0000:05:00.0
05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller
(rev 04) (prog-if 30 [XHCI])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f1d00000 (64-bit, non-prefetchable) [disabled]
[size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0
<4us, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: xhci_hcd
+ ---
+ AlsaVersion: Advanced Linux Sound Architecture Driver Version 1.0.24.
+ ApportVersion: 2.0.1-0ubuntu8
+ Architecture: amd64
+ ArecordDevices:
+ **** List of CAPTURE Hardware Devices ****
+ card 0: PCH [HDA Intel PCH], device 0: CONEXANT Analog [CONEXANT Analog]
+ Subdevices: 1/1
+ Subdevice #0: subdevice #0
+ AudioDevicesInUse:
+ USER PID ACCESS COMMAND
+ /dev/snd/controlC0: roland 2949 F.... pulseaudio
+ CRDA:
+ country NL:
+ (2402 - 2482 @ 40), (N/A, 20)
+ (5170 - 5250 @ 40), (N/A, 20), NO-OUTDOOR
+ (5250 - 5330 @ 40), (N/A, 20), NO-OUTDOOR, DFS
+ (5490 - 5710 @ 40), (N/A, 27), DFS
+ Card0.Amixer.info:
+ Card hw:0 'PCH'/'HDA Intel PCH at 0xf2720000 irq 52'
+ Mixer name : 'Intel CougarPoint HDMI'
+ Components : 'HDA:14f1506e,17aa21cf,00100002
HDA:80862805,80860101,00100000'
+ Controls : 37
+ Simple ctrls : 14
+ Card29.Amixer.info:
+ Card hw:29 'ThinkPadEC'/'ThinkPad Console Audio Control at EC reg 0x30, fw
unknown'
+ Mixer name : 'ThinkPad EC (unknown)'
+ Components : ''
+ Controls : 1
+ Simple ctrls : 1
+ Card29.Amixer.values:
+ Simple mixer control 'Console',0
+ Capabilities: pswitch pswitch-joined penum
+ Playback channels: Mono
+ Mono: Playback [on]
+ DistroRelease: Ubuntu 12.04
+ InstallationMedia: Ubuntu 11.10 "Oneiric Ocelot" - Release amd64 (20111012)
+ MachineType: LENOVO 4243W29
+ Package: linux (not installed)
+ ProcFB: 0 inteldrmfb
+ ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-3.2.0-24-generic
root=UUID=e5e65e59-f323-4df0-a813-dc393d2a4970 ro quiet splash vt.handoff=7
+ ProcVersionSignature: Ubuntu 3.2.0-24.39-generic 3.2.16
+ RelatedPackageVersions:
+ linux-restricted-modules-3.2.0-24-generic N/A
+ linux-backports-modules-3.2.0-24-generic N/A
+ linux-firmware 1.79
+ SourcePackage: linux
+ StagingDrivers: mei
+ Tags: precise staging precise staging
+ Uname: Linux 3.2.0-24-generic x86_64
+ UpgradeStatus: Upgraded to precise on 2012-04-24 (37 days ago)
+ UserGroups: adm admin audio cdrom dialout libvirtd lpadmin plugdev pulse
pulse-access sambashare vboxusers video
+ dmi.bios.date: 07/11/2011
+ dmi.bios.vendor: LENOVO
+ dmi.bios.version: 8AET49WW (1.29 )
+ dmi.board.asset.tag: Not Available
+ dmi.board.name: 4243W29
+ dmi.board.vendor: LENOVO
+ dmi.board.version: Not Available
+ dmi.chassis.asset.tag: LBNL02200
+ dmi.chassis.type: 10
+ dmi.chassis.vendor: LENOVO
+ dmi.chassis.version: Not Available
+ dmi.modalias:
dmi:bvnLENOVO:bvr8AET49WW(1.29):bd07/11/2011:svnLENOVO:pn4243W29:pvrThinkPadT520:rvnLENOVO:rn4243W29:rvrNotAvailable:cvnLENOVO:ct10:cvrNotAvailable:
+ dmi.product.name: 4243W29
+ dmi.product.version: ThinkPad T520
+ dmi.sys.vendor: LENOVO
** Attachment added: ".etc.asound.conf.txt"
https://bugs.launchpad.net/bugs/1006765/+attachment/3170015/+files/.etc.asound.conf.txt
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/1006765
Title:
Hot plugging USB3.0 express card Not possible
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1006765/+subscriptions
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
