And here the dmesg output with standard linux-image-generic after doing the resume, rmmod and modprobe again (I have done both _after_ resume):
[ 878.964468] ------------[ cut here ]------------ [ 878.964469] WARNING: at /build/buildd/linux-2.6.27/kernel/power/main.c:176 suspend_test_finish+0x75/0x80() [ 878.964471] Modules linked in: cbc aes_x86_64 aes_generic ecryptfs af_packet binfmt_misc rfcomm sco bnep l2cap bluetooth ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 xt_state nf_conntrack ipt_REJECT xt_tcpudp bridge stp kvm_intel kvm iscsi_trgt crc32c libcrc32c ppdev ipv6 acpi_cpufreq cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_conservative cpufreq_ondemand freq_table sbs wmi video output pci_slot sbshc container battery iptable_filter ip_tables x_tables ac w83627ehf hwmon_vid sbp2 parport_pc lp parport mt352 saa7134_dvb videobuf_dvb dvb_core saa7134_alsa mt20xx tea5767 tda9887 tda8290 tuner snd_hda_intel snd_pcm_oss snd_mixer_oss arc4 snd_pcm ecb crypto_blkcipher snd_seq_dummy saa7134 snd_seq_oss rt61pci crc_itu_t snd_seq_midi rt2x00pci rt2x00lib ir_common snd_rawmidi compat_ioctl32 rfkill snd_seq_midi_event snd_seq videodev v4l1_compat snd_timer led_class evdev dm_multipath snd_seq_device v4l2_common scsi_dh mac80211 pcspkr snd videobuf_dma_sg nvidia(P) videobuf_core tveeprom iTCO_wdt iTCO_vendor_support cfg80211 soundcore i2c_core eeprom_93cx6 button snd_page_alloc shpchp pci_hotplug ext3 jbd mbcache pata_acpi sr_mod sd_mod crc_t10dif cdrom usbhid hid sg pata_marvell ata_generic ohci1394 ahci ieee1394 skge sky2 libata scsi_mod dock ehci_hcd uhci_hcd usbcore raid10 raid456 async_xor async_memcpy async_tx xor raid1 raid0 multipath linear md_mod dm_mirror dm_log dm_snapshot dm_mod thermal processor fan fbcon tileblit font bitblit softcursor fuse compcache lzo_decompress lzo_compress tlsf [ 878.964528] Pid: 8168, comm: pm-suspend Tainted: P 2.6.27-7-generic #1 [ 878.964529] [ 878.964529] Call Trace: [ 878.964533] [<ffffffff8024e9b4>] warn_on_slowpath+0x64/0x90 [ 878.964536] [<ffffffff804fffa6>] ? printk+0x6c/0x6e [ 878.964538] [<ffffffff803a3fb7>] ? kobject_put+0x27/0x60 [ 878.964540] [<ffffffff80501049>] ? mutex_unlock+0x9/0x20 [ 878.964542] [<ffffffff80434e4a>] ? dpm_complete+0x18a/0x1a0 [ 878.964544] [<ffffffff8027e1a5>] suspend_test_finish+0x75/0x80 [ 878.964546] [<ffffffff8027e2b4>] suspend_devices_and_enter+0x104/0x1b0 [ 878.964547] [<ffffffff8027e571>] enter_state+0xe1/0x110 [ 878.964549] [<ffffffff8027e65a>] state_store+0xba/0x100 [ 878.964550] [<ffffffff803a3e57>] kobj_attr_store+0x17/0x20 [ 878.964552] [<ffffffff803495fa>] sysfs_write_file+0xca/0x140 [ 878.964555] [<ffffffff802e9e9b>] vfs_write+0xcb/0x130 [ 878.964556] [<ffffffff802e9ff5>] sys_write+0x55/0x90 [ 878.964559] [<ffffffff8021285a>] system_call_fastpath+0x16/0x1b [ 878.964560] [ 878.964560] ---[ end trace 3edda6dc2afa118b ]--- [ 878.964664] PM: Finishing wakeup. [ 878.964665] Restarting tasks ... done. [ 880.299660] skge eth0: enabling interface [ 880.303425] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 880.310442] sky2 eth1: enabling interface [ 880.314414] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 914.415716] phy0 -> rt61pci_mcu_request: Error - mcu request error. Request 0x50 failed for token 0xff. [ 914.416320] phy0 -> rt61pci_mcu_request: Error - mcu request error. Request 0x50 failed for token 0xff. [ 914.504746] rt61pci 0000:09:00.0: PCI INT A disabled [ 914.549899] ndiswrapper version 1.53 loaded (smp=yes, preempt=no) [ 914.551595] usbcore: registered new interface driver ndiswrapper [ 921.613709] rt61pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 921.621428] phy1: Selected rate control algorithm 'pid' [ 921.622966] Registered led device: rt61pci-phy1:radio [ 921.622980] Registered led device: rt61pci-phy1:assoc [ 925.636290] firmware: requesting rt2561s.bin [ 925.689922] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 932.148732] wlan0: authenticate with AP 00:1e:2a:5d:1d:c6 [ 932.150067] wlan0: authenticated [ 932.150072] wlan0: associate with AP 00:1e:2a:5d:1d:c6 [ 932.152650] wlan0: RX AssocResp from 00:1e:2a:5d:1d:c6 (capab=0x431 status=0 aid=2) [ 932.152655] wlan0: associated [ 932.153638] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 942.964004] wlan0: no IPv6 routers present -- rt61pci wireless card not working after suspend https://bugs.launchpad.net/bugs/294058 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
