This patch use the pinmux for mmc configuration for Trats Signed-off-by: Piotr Wilczek <p.wilc...@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.p...@samsung.com> CC: Minkyu Kang <mk7.k...@samsung.com> --- Chaneges for v2: - mmc iniatialisation using pinmux
board/samsung/trats/trats.c | 62 +++++++----------------------------------- 1 files changed, 11 insertions(+), 51 deletions(-) diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c index f5df56c..0fab2e0 100644 --- a/board/samsung/trats/trats.c +++ b/board/samsung/trats/trats.c @@ -29,6 +29,7 @@ #include <asm/arch/cpu.h> #include <asm/arch/gpio.h> #include <asm/arch/mmc.h> +#include <asm/arch/pinmux.h> #include <asm/arch/clock.h> #include <asm/arch/clk.h> #include <asm/arch/mipi_dsim.h> @@ -140,46 +141,16 @@ int board_mmc_init(bd_t *bis) { struct exynos4_gpio_part2 *gpio = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); - int i, err; + int err; /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */ s5p_gpio_direction_output(&gpio->k0, 2, 1); s5p_gpio_set_pull(&gpio->k0, 2, GPIO_PULL_NONE); - /* - * eMMC GPIO: - * SDR 8-bit@48MHz at MMC0 - * GPK0[0] SD_0_CLK(2) - * GPK0[1] SD_0_CMD(2) - * GPK0[2] SD_0_CDn -> Not used - * GPK0[3:6] SD_0_DATA[0:3](2) - * GPK1[3:6] SD_0_DATA[0:3](3) - * - * DDR 4-bit@26MHz at MMC4 - * GPK0[0] SD_4_CLK(3) - * GPK0[1] SD_4_CMD(3) - * GPK0[2] SD_4_CDn -> Not used - * GPK0[3:6] SD_4_DATA[0:3](3) - * GPK1[3:6] SD_4_DATA[4:7](4) - */ - for (i = 0; i < 7; i++) { - if (i == 2) - continue; - /* GPK0[0:6] special function 2 */ - s5p_gpio_cfg_pin(&gpio->k0, i, 0x2); - /* GPK0[0:6] pull disable */ - s5p_gpio_set_pull(&gpio->k0, i, GPIO_PULL_NONE); - /* GPK0[0:6] drv 4x */ - s5p_gpio_set_drv(&gpio->k0, i, GPIO_DRV_4X); - } - - for (i = 3; i < 7; i++) { - /* GPK1[3:6] special function 3 */ - s5p_gpio_cfg_pin(&gpio->k1, i, 0x3); - /* GPK1[3:6] pull disable */ - s5p_gpio_set_pull(&gpio->k1, i, GPIO_PULL_NONE); - /* GPK1[3:6] drv 4x */ - s5p_gpio_set_drv(&gpio->k1, i, GPIO_DRV_4X); + err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); + if (err) { + debug("SDMMC0 not configured\n"); + return err; } /* @@ -198,23 +169,12 @@ int board_mmc_init(bd_t *bis) * GPX3[4] T-flash detect pin */ if (!s5p_gpio_get_value(&gpio->x3, 4)) { - /* - * SD card GPIO: - * GPK2[0] SD_2_CLK(2) - * GPK2[1] SD_2_CMD(2) - * GPK2[2] SD_2_CDn -> Not used - * GPK2[3:6] SD_2_DATA[0:3](2) - */ - for (i = 0; i < 7; i++) { - if (i == 2) - continue; - /* GPK2[0:6] special function 2 */ - s5p_gpio_cfg_pin(&gpio->k2, i, 0x2); - /* GPK2[0:6] pull disable */ - s5p_gpio_set_pull(&gpio->k2, i, GPIO_PULL_NONE); - /* GPK2[0:6] drv 4x */ - s5p_gpio_set_drv(&gpio->k2, i, GPIO_DRV_4X); + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); + if (err) { + debug("SDMMC2 not configured\n"); + return err; } + err = s5p_mmc_init(2, 4); } -- 1.7.5.4 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot