The kmnusa board uses a mv88e6352 switch that is connected to the main
eth interface of the kirkwood. Therefore the switch must be configured
so that the kirkwood's egiga eth inferface can be used.
Signed-off-by: Valentin Longchamp <valentin.longch...@keymile.com>
Cc: Holger Brunck <holger.bru...@keymile.com>
Cc: Prafulla Wadaskar <prafu...@marvell.com>
---
board/keymile/km_arm/km_arm.c | 63 +++++++++++++++++++++++++++++++++++++++++
1 files changed, 63 insertions(+), 0 deletions(-)
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 2b2ca39..c0069c1 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -385,6 +385,69 @@ void reset_phy(void)
/* reset the phy */
miiphy_reset(name, CONFIG_PHY_BASE_ADR);
}
+#elif defined(CONFIG_KM_PIGGY4_88E6352)
+
+#include <mv88e6352.h>
+
+#if defined(CONFIG_KM_NUSA)
+struct mv88e_sw_reg extsw_conf[] = {
+ /* port 0, PIGY4, autoneg */
+ /* first the fix for the 1000Mbits Autoneg, this is from
+ * a Marvell errata, the regs are undocumented */
+ { PHY(0), PHY_PAGE, AN1000FIX_PAGE },
+ { PHY(0), PHY_STATUS, AN1000FIX },
+ { PHY(0), PHY_PAGE, 0 },
+ /* now the real port and phy configuration */
+ { PORT(0), PORT_PHY, NO_SPEED_FOR },
+ { PORT(0), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ { PHY(0), PHY_1000_CTRL, NO_ADV },
+ { PHY(0), PHY_SPEC_CTRL, AUTO_MDIX_EN },
+ { PHY(0), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
+ FULL_DUPLEX },
+ /* port 1, unused */
+ { PORT(1), PORT_CTRL, PORT_DIS },
+ { PHY(1), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(1), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 2, unused */
+ { PORT(2), PORT_CTRL, PORT_DIS },
+ { PHY(2), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 3, unused */
+ { PORT(3), PORT_CTRL, PORT_DIS },
+ { PHY(3), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(3), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 4, ICNEV, SerDes, SGMII */
+ { PORT(4), PORT_STATUS, NO_PHY_DETECT },
+ { PORT(4), PORT_PHY, SPEED_1000_FOR },
+ { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ { PHY(4), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(4), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 5, CPU_RGMII */
+ { PORT(5), PORT_PHY, RX_RGMII_TIM | TX_RGMII_TIM | FLOW_CTRL_EN |
+ FLOW_CTRL_FOR | LINK_VAL | LINK_FOR | FULL_DPX |
+ FULL_DPX_FOR | SPEED_1000_FOR },
+ { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ /* port 6, unused, this port has no phy */
+ { PORT(6), PORT_CTRL, PORT_DIS },
+};
+#else
+struct mv88e_sw_reg extsw_conf[] = {};
+#endif
+
+void reset_phy(void)
+{
+#if defined(CONFIG_KM_MVEXTSW_ADDR)
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
+ ARRAY_SIZE(extsw_conf));
+ mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
+#endif
+}
+
#else
/* Configure and enable MV88E1118 PHY on the piggy*/
void reset_phy(void)
--
1.7.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
