> -----Original Message----- > From: Holger Brunck [mailto:holger.bru...@keymile.com] > Sent: 09 August 2012 17:08 > To: u-boot@lists.denx.de > Cc: Holger Brunck; Prafulla Wadaskar; Valentin Longchamp; Gerlando > Falauto > Subject: [PATCH] arm/km: remove unused code > > For some reasons we had an own implementaion of dram_init and > dram_init_banksize. This is not needed anymore, use the standard > kirkwood functions instead. > > Signed-off-by: Holger Brunck <holger.bru...@keymile.com> > cc: Prafulla Wadaskar <prafu...@marvell.com> > cc: Valentin Longchamp <valentin.longch...@keymile.com> > cc: Gerlando Falauto <gerlando.fala...@keymile.com> > --- > board/keymile/km_arm/km_arm.c | 20 -------------------- > include/configs/km/keymile-common.h | 1 - > 2 files changed, 0 insertions(+), 21 deletions(-) > > diff --git a/board/keymile/km_arm/km_arm.c > b/board/keymile/km_arm/km_arm.c > index ac14a2f..2068b00 100644 > --- a/board/keymile/km_arm/km_arm.c > +++ b/board/keymile/km_arm/km_arm.c > @@ -332,26 +332,6 @@ void board_spi_release_bus(struct spi_slave > *slave) > kw_gpio_set_value(KM_FLASH_GPIO_PIN, 1); > } > > -int dram_init(void) > -{ > - /* dram_init must store complete ramsize in gd->ram_size */ > - /* Fix this */ > - gd->ram_size = get_ram_size((void *)kw_sdram_bar(0), > - kw_sdram_bs(0)); > - return 0; > -} > - > -void dram_init_banksize(void) > -{ > - int i; > - > - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { > - gd->bd->bi_dram[i].start = kw_sdram_bar(i); > - gd->bd->bi_dram[i].size = get_ram_size((long > *)kw_sdram_bar(i), > - kw_sdram_bs(i)); > - } > -} > - > #if (defined(CONFIG_KM_PIGGY4_88E6061)) > > #define PHY_LED_SEL_REG 0x18 > diff --git a/include/configs/km/keymile-common.h > b/include/configs/km/keymile-common.h > index 7ed9958..9983104 100644 > --- a/include/configs/km/keymile-common.h > +++ b/include/configs/km/keymile-common.h > @@ -81,7 +81,6 @@ > > #define CONFIG_LOADS_ECHO > #define CONFIG_SYS_LOADS_BAUD_CHANGE > -#define CONFIG_SYS_BOARD_DRAM_INIT /* Used board specific dram_init > */ > > #define CONFIG_I2C_MULTI_BUS > #define CONFIG_SYS_MAX_I2C_BUS 1 > --
Acked-By: Prafulla Wadaskar <prafu...@marvell.com> Will pull this patch soon. Regards... Prafulla . . . _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
