From: Lad, Prabhakar <prabhakar....@ti.com> This patch adds support for direct NOR boot mode on da850/omap-l138. Added da850evm_direct_nor entry in boards.cfg to allow to build targets.
Signed-off-by: Lad, Prabhakar <prabhakar....@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar....@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.ha...@ti.com> --- Changes for v2: 1: Added entry in boards.cfg to build target for direct NOR boot mode. Changes for v3: 1: Patch number chnaged due to patch split up of patch 6 of v2. boards.cfg | 1 + include/configs/da850evm.h | 22 ++++++++++++++++++++-- 2 files changed, 21 insertions(+), 2 deletions(-) diff --git a/boards.cfg b/boards.cfg index 0dee43f..2685b73 100644 --- a/boards.cfg +++ b/boards.cfg @@ -122,6 +122,7 @@ cam_enc_4xx arm arm926ejs cam_enc_4xx ait da830evm arm arm926ejs da8xxevm davinci davinci da850_am18xxevm arm arm926ejs da8xxevm davinci davinci da850evm:DA850_AM18X_EVM,MAC_ADDR_IN_EEPROM,SYS_I2C_EEPROM_ADDR_LEN=2,SYS_I2C_EEPROM_ADDR=0x50 da850evm arm arm926ejs da8xxevm davinci davinci da850evm:MAC_ADDR_IN_SPIFLASH +da850evm_direct_nor arm arm926ejs da8xxevm davinci davinci da850evm:MAC_ADDR_IN_SPIFLASH,USE_NOR,DIRECT_NOR_BOOT davinci_dm355evm arm arm926ejs dm355evm davinci davinci davinci_dm355leopard arm arm926ejs dm355leopard davinci davinci davinci_dm365evm arm arm926ejs dm365evm davinci davinci diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index a85d6e4..6f3fd1b 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -27,7 +27,10 @@ * Board */ #define CONFIG_DRIVER_TI_EMAC +/* check if direct NOR boot config is used */ +#ifndef CONFIG_DIRECT_NOR_BOOT #define CONFIG_USE_SPIFLASH +#endif /* @@ -43,10 +46,19 @@ #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) #define CONFIG_SYS_HZ 1000 -#define CONFIG_SYS_TEXT_BASE 0xc1080000 #define CONFIG_SYS_DA850_PLL_INIT #define CONFIG_SYS_DA850_DDR_INIT +#ifdef CONFIG_DIRECT_NOR_BOOT +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DA8XX_GPIO +#define CONFIG_SYS_TEXT_BASE 0x60000000 +#define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11) +#define CONFIG_DA850_LOWLEVEL +#else +#define CONFIG_SYS_TEXT_BASE 0xc1080000 +#endif + /* * Memory Info */ @@ -368,6 +380,7 @@ #define CONFIG_CMD_MMC #endif +#ifndef CONFIG_DIRECT_NOR_BOOT /* defines for SPL */ #define CONFIG_SPL #define CONFIG_SPL_SERIAL_SUPPORT @@ -377,7 +390,7 @@ #define CONFIG_SPL_STACK 0x8001ff00 #define CONFIG_SPL_TEXT_BASE 0x80000000 #define CONFIG_SPL_MAX_SIZE 32768 - +#endif /* Load U-Boot Image From MMC */ #ifdef CONFIG_SPL_MMC_LOAD @@ -390,6 +403,11 @@ /* additions for new relocation code, must added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0xc0000000 + +#ifdef CONFIG_DIRECT_NOR_BOOT +#define CONFIG_SYS_INIT_SP_ADDR 0x8001ff00 +#else #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ GENERATED_GBL_DATA_SIZE) +#endif /* CONFIG_DIRECT_NOR_BOOT */ #endif /* __CONFIG_H */ -- 1.7.4.1 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot