On 12/06/2012 18:37, Vikram Narayanan wrote:
> Changes from v1:
> Used appropriate gpio_* lib calls.
>
> ---
> Instead of manipulating gpio registers directly, use the calls
> from the gpio library.
Changelog must go after the "---" line and commit message before. They
are swapped. Apart of that..
>
> Signed-off-by: Vikram Narayanan <vikram...@gmail.com>
> Cc: Fabio Estevam <fabio.este...@freescale.com>
> Cc: John Rigby <jcri...@gmail.com>
> Cc: Stefano Babic <sba...@denx.de>
> ---
> board/karo/tx25/tx25.c | 25 +++++++++----------------
> 1 files changed, 9 insertions(+), 16 deletions(-)
>
> diff --git a/board/karo/tx25/tx25.c b/board/karo/tx25/tx25.c
> index 2a29943..ff2de38 100644
> --- a/board/karo/tx25/tx25.c
> +++ b/board/karo/tx25/tx25.c
> @@ -34,14 +34,13 @@
> DECLARE_GLOBAL_DATA_PTR;
>
> #ifdef CONFIG_FEC_MXC
> +#define GPIO_FEC_RESET_B MXC_GPIO_PORT_TO_NUM(4, 7)
> +#define GPIO_FEC_ENABLE_B MXC_GPIO_PORT_TO_NUM(4, 9)
> void tx25_fec_init(void)
> {
> struct iomuxc_mux_ctl *muxctl;
> struct iomuxc_pad_ctl *padctl;
> - u32 val;
> u32 gpio_mux_mode = MX25_PIN_MUX_MODE(5);
> - struct gpio_regs *gpio4 = (struct gpio_regs *)IMX_GPIO4_BASE;
> - struct gpio_regs *gpio3 = (struct gpio_regs *)IMX_GPIO3_BASE;
> u32 saved_rdata0_mode, saved_rdata1_mode, saved_rx_dv_mode;
>
> debug("tx25_fec_init\n");
> @@ -66,18 +65,15 @@ void tx25_fec_init(void)
> writel(0x0, &padctl->pad_d11);
>
> /* drop PHY power and assert reset (low) */
> - val = readl(&gpio4->gpio_dr) & ~((1 << 7) | (1 << 9));
> - writel(val, &gpio4->gpio_dr);
> - val = readl(&gpio4->gpio_dir) | (1 << 7) | (1 << 9);
> - writel(val, &gpio4->gpio_dir);
> + gpio_direction_output(GPIO_FEC_RESET_B, 0);
> + gpio_direction_output(GPIO_FEC_ENABLE_B, 0);
>
> mdelay(5);
>
> debug("resetting phy\n");
>
> /* turn on PHY power leaving reset asserted */
> - val = readl(&gpio4->gpio_dr) | 1 << 9;
> - writel(val, &gpio4->gpio_dr);
> + gpio_direction_output(GPIO_FEC_ENABLE_B, 1);
>
> mdelay(10);
>
> @@ -107,19 +103,16 @@ void tx25_fec_init(void)
> /*
> * set each to 1 and make each an output
> */
> - val = readl(&gpio3->gpio_dr) | (1 << 10) | (1 << 11) | (1 << 12);
> - writel(val, &gpio3->gpio_dr);
> - val = readl(&gpio3->gpio_dir) | (1 << 10) | (1 << 11) | (1 << 12);
> - writel(val, &gpio3->gpio_dir);
> + gpio_direction_output(MXC_GPIO_PORT_TO_NUM(3, 10), 1);
> + gpio_direction_output(MXC_GPIO_PORT_TO_NUM(3, 11), 1);
> + gpio_direction_output(MXC_GPIO_PORT_TO_NUM(3, 12), 1);
>
> mdelay(22); /* this value came from RedBoot */
>
> /*
> * deassert PHY reset
> */
> - val = readl(&gpio4->gpio_dr) | 1 << 7;
> - writel(val, &gpio4->gpio_dr);
> - writel(val, &gpio4->gpio_dr);
> + gpio_set_value(GPIO_FEC_RESET_B, 1);
>
> mdelay(5);
>
Acked-by: Stefano Babic <sba...@denx.de>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
