From: Vipin KUMAR <vipin.ku...@st.com>
Ethernet probing is removed from u-boot compiled as a firmware for spear
flashing utility. This enables faster access to usbtty interface as unused
ethernet i/f is not initialized.
Signed-off-by: Vipin Kumar <vipin.ku...@st.com>
Signed-off-by: Amit Virdi <amit.vi...@st.com>
---
include/configs/spear-common.h | 10 ++++++++++
include/configs/spear3xx_evb.h | 3 ++-
include/configs/spear6xx_evb.h | 1 -
3 files changed, 12 insertions(+), 2 deletions(-)
diff --git a/include/configs/spear-common.h b/include/configs/spear-common.h
index f4980b0..14e3ec4 100644
--- a/include/configs/spear-common.h
+++ b/include/configs/spear-common.h
@@ -27,6 +27,7 @@
* Common configurations used for both spear3xx as well as spear6xx
*/
+#if !defined(CONFIG_SPEAR_USBTTY)
/* Ethernet driver configuration */
#define CONFIG_MII
#define CONFIG_DESIGNWARE_ETH
@@ -34,6 +35,7 @@
#define CONFIG_DW0_PHY 1
#define CONFIG_NET_MULTI
#define CONFIG_PHY_RESET_DELAY (10000) /* in usec */
+#endif
/* USBD driver configuration */
#define CONFIG_DW_UDC
@@ -109,14 +111,22 @@
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_RUN
#define CONFIG_CMD_SAVES
+
+#if !defined(CONFIG_SPEAR_USBTTY)
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
+#endif
/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <config_cmd_default.h>
+#if defined(CONFIG_SPEAR_USBTTY)
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#endif
+
/*
* Default Environment Varible definitions
*/
diff --git a/include/configs/spear3xx_evb.h b/include/configs/spear3xx_evb.h
index 263c058..84fad0c 100644
--- a/include/configs/spear3xx_evb.h
+++ b/include/configs/spear3xx_evb.h
@@ -51,6 +51,7 @@
#include <configs/spear-common.h>
+#if !defined(CONFIG_SPEAR_USBTTY)
/* Ethernet driver configuration */
#define CONFIG_DW_ALTDESCRIPTOR 1
@@ -66,6 +67,7 @@
#define CONFIG_MACB0_PHY 0x01
#endif
+#endif
/* Serial Configuration (PL011) */
#define CONFIG_SYS_SERIAL0 0xD0000000
@@ -144,7 +146,6 @@
#endif
/* NAND flash configuration */
-#define CONFIG_SYS_FSMC_NAND_SP
#define CONFIG_SYS_FSMC_NAND_8BIT
#if defined(CONFIG_SPEAR300)
diff --git a/include/configs/spear6xx_evb.h b/include/configs/spear6xx_evb.h
index a61d9be..d901ba8 100644
--- a/include/configs/spear6xx_evb.h
+++ b/include/configs/spear6xx_evb.h
@@ -49,7 +49,6 @@
(void *)CONFIG_SYS_SERIAL1 }
/* NAND flash configuration */
-#define CONFIG_SYS_FSMC_NAND_SP
#define CONFIG_SYS_FSMC_NAND_8BIT
#define CONFIG_SYS_NAND_BASE (0xD2000000)
--
1.7.2.2
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
