Hi Peter,
Some comments (hopefully last ones) in addition to Wolfgang's and Tom's:
On 12/16/11 22:31, Peter Barada wrote:
> This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo
> reference boards. It assumes U-boot is loaded to SDRAM with the
> help of another small bootloader (x-load) running from SRAM.
>
> Signed-off-by: Peter Barada <peter.bar...@logicpd.com>
> Cc: Tom Rini <tom.r...@gmail.com>
> Cc: Igor Grinberg <grinb...@compulab.co.il>
> ---
>
> Changes for V3:
> Inline identify_board() into board_init()
> Remove triple empty lines
> Use sdelay() instead of naked delay loop
> Use enable_gpmc_cs_config() to setup GPMC CS1 access to LAN92xx
> Remove CONFIG_L2_OFF - holdover from previous work in u-boot-2011.06
> where adding 270p 32bpp frambuffer support cause failure while
> booting linux kernel. Will address when I add video support
> Reduce CONFIG_SYS_MAXARGS to 16
>
> Changes for V2:
> Rework logic_identify() into identify_board() - can't use checkboard()
> since its enabled by CONFIG_DISPLAY_BOARDINFO
> Properly indent comments in set_muxconf_regs()
> Move setup_net_chip() call from misc_init_r to board_eth_init()
> Remove triple empty line spacing
> Pass gpio_request(189) non-empty description
> Remove board/logicpd/omap3som/config.mk
> Remove clean/distclean from board/logicpd/omap3som/Makefile
> Modify board_mmc_init() to be one line function
> Modify include/configs/omap3_logic.h to use on/off #defines
>
> board/logicpd/omap3som/Makefile | 42 +++
> board/logicpd/omap3som/omap3logic.c | 523
> +++++++++++++++++++++++++++++++++++
> board/logicpd/omap3som/omap3logic.h | 35 +++
> boards.cfg | 1 +
> include/configs/omap3_logic.h | 351 +++++++++++++++++++++++
> 5 files changed, 952 insertions(+), 0 deletions(-)
> create mode 100644 board/logicpd/omap3som/Makefile
> create mode 100644 board/logicpd/omap3som/omap3logic.c
> create mode 100644 board/logicpd/omap3som/omap3logic.h
> create mode 100644 include/configs/omap3_logic.h
[...]
> diff --git a/board/logicpd/omap3som/omap3logic.c
> b/board/logicpd/omap3som/omap3logic.c
> new file mode 100644
> index 0000000..eb051db
> --- /dev/null
> +++ b/board/logicpd/omap3som/omap3logic.c
[...]
> +/*
> + * Routine: board_init
> + * Description: Early hardware init.
> + */
> +int board_init(void)
> +{
> + struct board_id *board;
> + unsigned int val;
> +
> + gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
> +
> + /* boot param addr */
> + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
> +
> + /*
> + * To identify between a SOM LV and Torpedo module,
> + * a pulldown resistor is on hsusb0_data5 for the SOM LV module.
> + * Drive the pin (and let it soak), then read it back.
> + * If the pin is still high its a Torpedo. If low its a SOM LV
> + */
> +
> + /* Mux hsusb0_data5 as a GPIO */
> + MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M4));
> +
> + if (gpio_request(GPIO_189, "husb0_data5.gpio_189") == 0) {
Usually, by the label goes the functionality it is used for
in current request, but af course it is up to you, it is not a
blocker as long as the label is valid.
> +
> + /* Drive GPIO_189 - the pulldown resistor on the SOM LV
> + * will drain the voltage */
incorrect multi-line comment (fix globally) and probably,
the empty line before it can be removed.
> + gpio_direction_output(GPIO_189, 0);
> + gpio_set_value(GPIO_189, 1);
> +
> + /* Let it soak for a bit */
> + sdelay(0x100);
> +
> + /* Read state of GPIO_189 as an input and if its set.
> + * If so the board is a Torpedo */
> + gpio_direction_input(GPIO_189);
> + val = gpio_get_value(GPIO_189);
> + gpio_free(GPIO_189);
> +
> + board = &boards[!!(get_cpu_family() == CPU_OMAP36XX)][!!val];
> + printf("Board: %s\n", board->name);
> +
> + /* Set the machine_id passed to Linux */
> + gd->bd->bi_arch_number = board->machine_id;
> + }
> +
> + /* restore hsusb0_data5 pin as hsusb0_data5 */
> + MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0));
> +
> + return 0;
> +}
[...]
> +/*
> + * Routine: misc_init_r
> + * Description: Init ethernet (done here so udelay works)
Function changed, comment left...
> + */
> +int misc_init_r(void)
> +{
> + dieid_num_r();
> +
> + return 0;
> +}
[...]
--
Regards,
Igor.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
