> Sorry guys; I'm bailing. > > Out. Well ... it can't be helped.
M > > On Nov 24, 2011, at 1:15, Marek Vasut wrote: > >> This patch adds a validity check for GPIO pins to prevent clobbering > >> reserved bit or even registers, per suggestion of Marek Vasut. > >> > >> Please note: > >> 1. gpio_request no longer checks validity. Pin validity must be checked > >> explicitly use gpio_invalid prior to request and hence use. Previous > >> validity check in gpio_request was incomplete anyway. 2. MX233 is not > >> supported yet. Until it is, macros defining the number of pins for each > >> bank reside in arch/arm/include/asm/arch-mx28/iomux.h > >> > >> Signed-off-by: Robert Deliën <robert at delien.nl<http://delien.nl/>> > > > > AARGH! Please add the following lines to the commit message: > > > > Cc: Marek Vasut <marek.va...@gmail.com> > > Cc: Stefano Babic <sba...@denx.de> > > > > !!!! > > > > That way, you won't have to care for the Cc, which you forgot again! > > > >> diff --git a/arch/arm/include/asm/arch-mx28/gpio.h > >> b/arch/arm/include/asm/arch-mx28/gpio.h index be1c944..5abd7b1 100644 > >> --- a/arch/arm/include/asm/arch-mx28/gpio.h > >> +++ b/arch/arm/include/asm/arch-mx28/gpio.h > >> @@ -25,6 +25,10 @@ > >> > >> #ifdef CONFIG_MXS_GPIO > >> void mxs_gpio_init(void); > >> + > >> +extern int gpio_invalid(int gp); > >> +#define gpio_invalid(gpio) gpio_invalid(gpio) > >> + > > > > Please, gpio_is_valid() and invert the logic. > > > >> #else > >> inline void mxs_gpio_init(void) {} > >> #endif > >> diff --git a/arch/arm/include/asm/arch-mx28/iomux.h > >> b/arch/arm/include/asm/arch-mx28/iomux.h index 7abdf58..2326fdb 100644 > >> --- a/arch/arm/include/asm/arch-mx28/iomux.h > >> +++ b/arch/arm/include/asm/arch-mx28/iomux.h > >> @@ -56,6 +56,16 @@ typedef u32 iomux_cfg_t; > >> #define MXS_PAD_PULL_VALID_SHIFT 16 > >> #define MXS_PAD_PULL_VALID_MASK ((iomux_cfg_t)0x1 << > >> MXS_PAD_PULL_VALID_SHIFT) > >> > >> +#define MX28_BANK0_PINS 29 > >> +#define MX28_BANK1_PINS 32 > >> +#define MX28_BANK2_PINS 28 > >> +#define MX28_BANK3_PINS 31 > >> +#define MX28_BANK4_PINS 21 > >> + > >> +#define MX23_BANK0_PINS 32 > >> +#define MX23_BANK1_PINS 31 > >> +#define MX23_BANK2_PINS 32 > >> + > > > > It's not used anywhere else than mxs_gpio.c, so define it there to reduce > > the scope. Also, I'd be just for using array of numbers with explanation > > comment to avoid making the code unnecessarily bigger. > > > >> #define PAD_MUXSEL_0 0 > >> #define PAD_MUXSEL_1 1 > >> #define PAD_MUXSEL_2 2 > >> diff --git a/common/cmd_gpio.c b/common/cmd_gpio.c > >> index 9cc790a..51e11e7 100644 > >> --- a/common/cmd_gpio.c > >> +++ b/common/cmd_gpio.c > >> @@ -15,6 +15,10 @@ > >> #define name_to_gpio(name) simple_strtoul(name, NULL, 10) > >> #endif > >> > >> +#ifndef gpio_invalid > >> +#define gpio_invalid(gpio) (0) > >> +#endif > >> + > >> enum gpio_cmd { > >> > >> GPIO_INPUT, > >> GPIO_SET, > >> > >> @@ -56,6 +60,12 @@ static int do_gpio(cmd_tbl_t *cmdtp, int flag, int > >> argc, char * const argv[]) if (gpio < 0) > >> > >> goto show_usage; > >> > >> + /* check bank and pin number for validity */ > >> + if (gpio_invalid(gpio)) { > >> + printf("gpio: invalid pin %u\n", gpio); > >> + return -1; > >> + } > >> + > > > > Please separate this cmd_gpio() part out! Are you ignoring my previous > > comments completely ? > > > >> /* grab the pin before we tweak it */ > >> if (gpio_request(gpio, "cmd_gpio")) { > >> printf("gpio: requesting pin %u failed\n", gpio); > >> > >> diff --git a/drivers/gpio/mxs_gpio.c b/drivers/gpio/mxs_gpio.c > >> index b7e9591..dabee90 100644 > >> --- a/drivers/gpio/mxs_gpio.c > >> +++ b/drivers/gpio/mxs_gpio.c > >> @@ -31,7 +31,6 @@ > >> #include <asm/arch/imx-regs.h> > >> > >> #if defined(CONFIG_MX23) > >> -#define PINCTRL_BANKS 3 > >> #define PINCTRL_DOUT(n) (0x0500 + ((n) * 0x10)) > >> #define PINCTRL_DIN(n) (0x0600 + ((n) * 0x10)) > >> #define PINCTRL_DOE(n) (0x0700 + ((n) * 0x10)) > >> @@ -39,7 +38,6 @@ > >> #define PINCTRL_IRQEN(n) (0x0900 + ((n) * 0x10)) > >> #define PINCTRL_IRQSTAT(n) (0x0c00 + ((n) * 0x10)) > >> #elif defined(CONFIG_MX28) > >> -#define PINCTRL_BANKS 5 > >> #define PINCTRL_DOUT(n) (0x0700 + ((n) * 0x10)) > >> #define PINCTRL_DIN(n) (0x0900 + ((n) * 0x10)) > >> #define PINCTRL_DOE(n) (0x0b00 + ((n) * 0x10)) > >> @@ -57,11 +55,25 @@ > >> #define GPIO_INT_LEV_MASK (1 << 0) > >> #define GPIO_INT_POL_MASK (1 << 1) > >> > >> +static const int mxs_bank_pins[] = { > >> +#if defined(CONFIG_MX23) > >> + MX23_BANK0_PINS, > >> + MX23_BANK1_PINS, > >> + MX23_BANK2_PINS > >> +#elif defined(CONFIG_MX28) > >> + MX28_BANK0_PINS, > >> + MX28_BANK1_PINS, > >> + MX28_BANK2_PINS, > >> + MX28_BANK3_PINS, > >> + MX28_BANK4_PINS > >> +#endif > > > > Ignoring? I asked you to define it above and don't duplicate the ifdefs. > > > >> +}; > >> + > >> void mxs_gpio_init(void) > >> { > >> > >> int i; > >> > >> - for (i = 0; i < PINCTRL_BANKS; i++) { > >> + for (i = 0; i < ARRAY_SIZE(mxs_bank_pins); i++) { > >> > >> writel(0, MXS_PINCTRL_BASE + PINCTRL_PIN2IRQ(i)); > >> writel(0, MXS_PINCTRL_BASE + PINCTRL_IRQEN(i)); > >> /* Use SCT address here to clear the IRQSTAT bits */ > >> > >> @@ -69,6 +81,16 @@ void mxs_gpio_init(void) > >> > >> } > >> > >> } > >> > >> +int gpio_invalid(int gp) > >> +{ > >> + if ( (gp & ~(MXS_PAD_BANK_MASK | MXS_PAD_PIN_MASK)) || > >> + (PAD_BANK(gp) >= ARRAY_SIZE(mxs_bank_pins)) || > >> + (PAD_PIN(gp) >= mxs_bank_pins[PAD_BANK(gp)]) ) > >> + return -EINVAL; > >> + > >> + return 0; > >> +} > >> + > >> int gpio_get_value(int gp) > >> { > >> > >> uint32_t bank = PAD_BANK(gp); > >> > >> @@ -120,9 +142,6 @@ int gpio_direction_output(int gp, int value) > >> > >> int gpio_request(int gp, const char *label) > >> { > >> - if (PAD_BANK(gp) > PINCTRL_BANKS) > >> - return -EINVAL; > >> - > >> > >> return 0; > >> > >> } > > > > Please make a checklist before resubmitting. Also, one more thing, submit > > this as a series to avoid this mess of patches: > > > > git format-patch --cover-letter HEAD~3 -o my_awesome_series > > vim my_awesome_series/0000-* > > <create some sane cover letter, add Cc: lines there too!!!> > > git send-email --annotate --to="u-boot@lists.denx.de" my_awesome_series/* > > > > Then when someone tells you it's completely wrong ;-) > > > > git format-patch etc. > > git send-email only the patches which you changed, and use the Message-ID > > for in-reply-to to particular patches, so the mail threading is right. > > > > M _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot