Hi Albert, On Thu, Oct 27, 2011 at 3:32 PM, Wolfgang Denk <w...@denx.de> wrote: > Dear Albert ARIBAUD, > > In message <4ea9bb69.8050...@aribaud.net> you wrote: >> Hi Wolfgang, >> >> The following changes since commit c30a15e590c7e5bfd27e4704c81648071f11d51f: >> >> FAT: Add FAT write feature (2011-10-26 21:40:44 +0200) >> >> are available in the git repository at: >> git://git.denx.de/u-boot-arm master >> >> Ajay Bhargav (4): >> SPI: Add SPI driver support for Marvell Armada100 >> Armada100: Add SPI support for Marvell gplugD >> Armada100: Add SPI flash support for Marvell gplugD >> Armada100: Add env storage support for Marvell gplugD >> >> Aneesh V (1): >> omap: spl: fix build break due to changes in FAT >> >> Chandan Nath (5): >> ARM:AM33XX: Added support for AM33xx >> ARM:AM33XX: Add clock definitions >> ARM:AM33XX: Add emif/ddr support >> ARM:AM33XX: Added timer support >> ARM:AM33XX: Add support for TI AM335X EVM >> >> Christian Riesch (1): >> da850evm: Move LPSC configuration to board_early_init_f() >> >> Fabio Estevam (2): >> mx31pdk: Remove unneeded config >> imx: fix coding style >> >> Heiko Schocher (4): >> arm, logbuffer: make it compileclean >> cosmetic, post: Codingstyle cleanup >> arm, post: add missing post_time_ms for arm >> arm, davinci: add missing LSPC define for MMC/SD1 >> >> Helmut Raiger (1): >> mx31: provide readable WEIM CS accessor >> >> Ilya Yanok (1): >> omap3/emif4: fix registers definition >> >> Jason Cooper (1): >> dreamplug: initial board support. >> >> Joe Hershberger (2): >> omap: Don't use gpio_free to change direction to input >> omap4_panda: Build in cmd_gpio support on panda >> >> Lei Wen (9): >> ARM: pantheon: reduce dependence of including platform file >> ARM: armada100: reduce dependence of including platform file >> ARM: kirkwood: reduce dependence of including platform file >> serial: reduce include platform file for marvell chip >> ARM: orion5x: reduce dependence of including platform file >> gpio: mvmfp: reduce include platform file >> ARM: pantheon: add mmc definition >> Marvell: dkb: add mmc support >> dkb: make mmc command as default enabled >> >> Manjunath Hadli (6): >> dm644X: revert cache disable patch >> dm36x: revert cache disable patch >> da830: add support for NAND boot mode >> davinci: emac: add new features to autonegotiate for EMAC >> davinci: emac: add support for more than 1 PHYs >> davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM >> >> Marek Vasut (2): >> ARM: Update mach-types >> I2C: Add i2c_get/set_speed() to mxc_i2c.c >> >> Michael Walle (1): >> kirkwood_spi: add dummy spi_init() >> >> Philip Balister (3): >> OMAP3: overo : Use ttyO2 instead of ttyS2. >> OMAP3: overo: Move ethernet CS4 configuration to execute based on >> board id >> OMAP3: overo : Add environment variable optargs to bootargs >> >> Prafulla Wadaskar (1): >> gplug: fixed build error as a result of code cleanup patch >> >> Ricardo Salveti de Araujo (3): >> omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL >> omap4: adding revision detection for 4460 ES1.1 >> omap4: splitting padconfs into common, 4430 and 4460 >> >> Rob Herring (1): >> ARM: Add Calxeda Highbank platform >> >> SRICHARAN R (1): >> U-Boot/SPL: omap4: Make ddr pre-calculated timings as default. >> >> Sergei Shtylyov (1): >> DaVinci: correct MDSTAT.STATE mask >> >> Simon Glass (5): >> tegra2: Rename CLOCK_PLL_ID to CLOCK_ID >> tegra2: Clean up board code a little >> tegra2: Add more clock functions >> tegra2: Rename PIN_ to PINGRP_ >> tegra2: Add more pinmux functions >> >> Simon Schwarz (6): >> devkit8000: protect board_mmc_init >> devkit8000: Add config to enable SPL MMC boot >> omap3: Add Base register for DMA >> omap3: Add DMA register accessors >> omap3: Add interface for omap3 DMA >> SPL: Add DMA library >> >> Stefano Babic (15): >> MX51: vision2: Set global macros >> misc: pmic: Freescale PMIC switches to generic PMIC driver >> MX5: vision2: use new pmic driver >> RTC: Switch mc13783 to generic pmic code >> MX3: qong: use new pmic driver >> MX5: efikamx/efikasb: use new pmic driver >> misc: pmic: use I2C_SET_BUS in pmic I2C >> misc: pmic: addI2C support to pmic_fsl driver >> MX35: mx35pdk: use new pmic driver >> MX5: mx51evk: use new pmic driver >> MX5: mx53evk: use new pmic driver >> MX31: mx31_litekit: use new pmic driver >> MX31: mx31ads: use new pmic driver >> MX31: mx31pdk: use new pmic driver >> misc: pmic: drop old Freescale's pmic driver >> >> Steve Sakoman (3): >> omap: overo: Configure mux for gpio10 >> omap: overo: Disable pull-ups on camera PCLK, HS and VS signals >> omap: beagle: Use ubifs instead of jffs2 for nand boot >> >> Tom Rini (3): >> OMAP3 SPL: Provide weak omap_rev_string >> devkit8000: Add malloc space >> mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset >> >> Tom Warren (1): >> tegra2: Enable MMC for Seaboard
You have Tom's MMC patch here but not the series from Stephen. Please can you see my email below about this: On Thu, Oct 20, 2011 at 3:57 PM, Simon Glass <s...@chromium.org> wrote: > Hi Albert, Wolfgang, > > I believe this is the current status on Tegra2 in u-boot-arm.git: > > - Stephen Warren has a patch series ending here: > http://patchwork.ozlabs.org/patch/119325/ > - Stephen Warren has a single GPIO patch here: > http://patchwork.ozlabs.org/patch/118184/ > - I have a boot refactor patch series ending here: > http://patchwork.ozlabs.org/patch/119941/ > > I think all of these have passed review, so I hope they can be > applied. They need to be applied in above order though. If there are > any problems I am on-hand to rebase, etc. The boot patch is actually still in review but I believe Stephen's patches are ready. Regards, Simon _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
