Hi, Stefano, On Sat, Oct 8, 2011 at 6:07 PM, Stefano Babic <sba...@denx.de> wrote: > Switch to new pmic generic driver. > > Signed-off-by: Stefano Babic <sba...@denx.de> > CC: Jason Liu <jason....@linaro.org> > --- > board/freescale/mx53evk/mx53evk.c | 15 +++++++++------ > include/configs/mx53evk.h | 5 +++-- > 2 files changed, 12 insertions(+), 8 deletions(-) > > diff --git a/board/freescale/mx53evk/mx53evk.c > b/board/freescale/mx53evk/mx53evk.c > index fd821c0..af0948f 100644 > --- a/board/freescale/mx53evk/mx53evk.c > +++ b/board/freescale/mx53evk/mx53evk.c > @@ -32,6 +32,7 @@ > #include <i2c.h> > #include <mmc.h> > #include <fsl_esdhc.h> > +#include <pmic.h> > #include <fsl_pmic.h> > #include <asm/gpio.h> > #include <mc13892.h> > @@ -124,12 +125,13 @@ static void setup_i2c(unsigned int port_number) > void power_init(void) > { > unsigned int val; > + struct pmic *p = get_pmic(); > > /* Set VDDA to 1.25V */ > - val = pmic_reg_read(REG_SW_2); > + pmic_reg_read(p, REG_SW_2, &val); > val &= ~SWX_OUT_MASK; > val |= SWX_OUT_1_25; > - pmic_reg_write(REG_SW_2, val); > + pmic_reg_write(p, REG_SW_2, val); > > /* > * Need increase VCC and VDDA to 1.3V > @@ -137,16 +139,16 @@ void power_init(void) > */ > if (is_soc_rev(CHIP_REV_2_0) == 0) { > /* Set VCC to 1.3V for TO2 */ > - val = pmic_reg_read(REG_SW_1); > + pmic_reg_read(p, REG_SW_1, &val); > val &= ~SWX_OUT_MASK; > val |= SWX_OUT_1_30; > - pmic_reg_write(REG_SW_1, val); > + pmic_reg_write(p, REG_SW_1, val); > > /* Set VDDA to 1.3V for TO2 */ > - val = pmic_reg_read(REG_SW_2); > + pmic_reg_read(p, REG_SW_2, &val); > val &= ~SWX_OUT_MASK; > val |= SWX_OUT_1_30; > - pmic_reg_write(REG_SW_2, val); > + pmic_reg_write(p, REG_SW_2, val); > } > } > > @@ -364,6 +366,7 @@ int board_init(void) > int board_late_init(void) > { > setup_i2c(1); > + pmic_init(); > power_init(); > > return 0; > diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h > index b127b06..dfe07bf 100644 > --- a/include/configs/mx53evk.h > +++ b/include/configs/mx53evk.h > @@ -59,8 +59,9 @@ > #define CONFIG_SYS_I2C_SLAVE 0xfe > > /* PMIC Configs */ > -#define CONFIG_FSL_PMIC > -#define CONFIG_FSL_PMIC_I2C > +#define CONFIG_PMIC > +#define CONFIG_PMIC_I2C > +#define CONFIG_PMIC_FSL > #define CONFIG_SYS_FSL_PMIC_I2C_ADDR 8 > > /* MMC Configs */
Acked-by: Jason Liu <jason....@linaro.org> > -- > 1.7.1 > > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot