--- a/board/efikamx/efikamx-usb.c
+++ b/board/efikamx/efikamx-usb.c
@@ -154,6 +154,7 @@ void efika_usb_phy_reset(void)
gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_D27), 1);
}
+
/*
* Configure control registers of the USB controller
*/
@@ -161,56 +162,56 @@ void control_regs_setup(void)
{
uint32_t tmp;
- tmp = readl(OTG_BASE_ADDR + 0x800);
- tmp &= ~((1 << 27) | (1 << 24) | (1 << 12) | (1 << 11));
- tmp |= 1 << 8;
- writel(tmp, OTG_BASE_ADDR + 0x800);
+ tmp = readl(OTG_BASE_ADDR + MX51_USB_CTRL_OFFSET);
+ tmp &= ~(MX51_OTG_WUE_BIT | MX51_OTG_PM_BIT | MX51_H1_ULPI_IE_BIT |
MX51_H1_WUE_BIT);
+ tmp |= MX51_H1_PM_BIT;
+ writel(tmp, OTG_BASE_ADDR + MX51_USB_CTRL_OFFSET);
- tmp = readl(OTG_BASE_ADDR + 0x808);
- tmp &= ~(1 << 8);
- tmp |= 1 << 5;
- writel(tmp, OTG_BASE_ADDR + 0x808);
+ tmp = readl(OTG_BASE_ADDR + MX51_PHY_CTRL0_OFFSET);
+ tmp &= ~MX51_OTG_OVERCURD_BIT;
+ tmp |= MX51_EHCI_POWERPINSE_BIT;
+ writel(tmp, OTG_BASE_ADDR + MX51_PHY_CTRL0_OFFSET);
- tmp = readl(OTG_BASE_ADDR + 0x80c);
- tmp &= ~0x3;
- tmp |= 0x1;
- writel(tmp, OTG_BASE_ADDR + 0x80c);
+ tmp = readl(OTG_BASE_ADDR + MX51_PHY_CTRL1_OFFSET);
+ tmp &= ~0x3; /* make sure bits 0 and 1 are set to zero */
+ tmp |= MX51_SYSCLOCK_24_MHZ_BIT;
+ writel(tmp, OTG_BASE_ADDR + MX51_PHY_CTRL1_OFFSET);
- tmp = readl(OTG_BASE_ADDR + 0x810);
- tmp |= 1 << 25;
- writel(tmp, OTG_BASE_ADDR + 0x810);
+ tmp = readl(OTG_BASE_ADDR + MX51_USB_CTRL1_OFFSET);
+ tmp |= MX51_H1_EXTCLKE_BIT;
+ writel(tmp, OTG_BASE_ADDR + MX51_USB_CTRL1_OFFSET);
- tmp = readl(OTG_BASE_ADDR + 0x814);
- tmp &= ~((1 << 8) | (1 << 7));
- tmp |= 1 << 4;
- writel(tmp, OTG_BASE_ADDR + 0x814);
+ tmp = readl(OTG_BASE_ADDR + MX51_UH2_CTRL_OFFSET);
+ tmp &= ~(MX51_H2_ULPI_IE_BIT | MX51_H2_WUE_BIT);
+ //Host 2 VBUS enable controlled by Host 2 controller
+ tmp |= MX51_H2_PM_BIT;
+ writel(tmp, OTG_BASE_ADDR + MX51_UH2_CTRL_OFFSET);
udelay(10000);
}
-#define ULPI_VIEWPORT(base) (base + 0x170)
void ulpi_write(u32 base, u32 reg, u32 value)
{
- if (!(readl(ULPI_VIEWPORT(base)) & (1 << 27))) {
- writel(1 << 31, ULPI_VIEWPORT(base));
- while (readl(ULPI_VIEWPORT(base)) & (1 << 31));
+ if (!(readl(ULPI_VIEWPORT(base)) & MX51_ULPI_SS_BIT)) {
+ writel(MX51_ULPI_WU_BIT, ULPI_VIEWPORT(base));
+ while (readl(ULPI_VIEWPORT(base)) & MX51_ULPI_WU_BIT);
}
- writel((1 << 30) | (1 << 29) | (reg << 16) | (value & 0xff),
ULPI_VIEWPORT(base));
- while (readl(ULPI_VIEWPORT(base)) & (1 << 30));
+ writel(MX51_ULPI_RWRUN | MX51_ULPI_RWCTRL | (reg << 16) | (value &
0xff), ULPI_VIEWPORT(base));
+ while (readl(ULPI_VIEWPORT(base)) & MX51_ULPI_RWRUN);
}
u32 ulpi_read(u32 base, u32 reg)
{
u32 tmp;
- if (!(readl(ULPI_VIEWPORT(base)) & (1 << 27))) {
- writel(1 << 31, ULPI_VIEWPORT(base));
- while (readl(ULPI_VIEWPORT(base)) & (1 << 31));
+ if (!(readl(ULPI_VIEWPORT(base)) & MX51_ULPI_SS_BIT)) {
+ writel(MX51_ULPI_WU_BIT, ULPI_VIEWPORT(base));
+ while (readl(ULPI_VIEWPORT(base)) & MX51_ULPI_WU_BIT);
}
- writel((1 << 30) | (reg << 16), ULPI_VIEWPORT(base));
+ writel(MX51_ULPI_RWRUN | (reg << 16), ULPI_VIEWPORT(base));
do {
tmp = readl(ULPI_VIEWPORT(base));
- } while (tmp & (1 << 30));
+ } while (tmp & MX51_ULPI_RWRUN);
return (tmp >> 8) & 0xff;
}
diff --git a/include/usb/ehci-fsl.h b/include/usb/ehci-fsl.h
index 67600ed..3af7928 100644
--- a/include/usb/ehci-fsl.h
+++ b/include/usb/ehci-fsl.h
@@ -169,9 +169,46 @@
#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC512x_USB_ADDR
#endif
+/* Register offsets for MX51 */
+#define MX51_USB_CTRL_OFFSET 0x800
+#define MX51_PHY_CTRL0_OFFSET 0x808
+#define MX51_PHY_CTRL1_OFFSET 0x80c
+#define MX51_USB_CTRL1_OFFSET 0x810
+#define MX51_UH2_CTRL_OFFSET 0x814
+
+/* Some USB_CTRL register bits*/
+#define MX51_OTG_WUE_BIT (1 << 27)
+#define MX51_OTG_PM_BIT (1 << 24)
+#define MX51_H1_ULPI_IE_BIT (1 << 12)
+#define MX51_H1_WUE_BIT (1 << 11)
+#define MX51_H1_PM_BIT (1 << 8)
+
+/* Some PHY_CTRL_0 register bits */
+#define MX51_OTG_OVERCURD_BIT (1 << 8)
+#define MX51_EHCI_POWERPINSE_BIT (1 << 5)
+
+/* Some PHY_CTRL_1 register bits */
+#define MX51_SYSCLOCK_24_MHZ_BIT (1 << 0)
+
+/* Some USB_CTRL_1 register bits*/
+#define MX51_H1_EXTCLKE_BIT (1 << 25)
+
+/* Some USB Host 2 CTRL register bits*/
+#define MX51_H2_ULPI_IE_BIT (1 << 8)
+#define MX51_H2_WUE_BIT (1 << 7)
+#define MX51_H2_PM_BIT (1 << 4)
+
+#define ULPI_VIEWPORT(base) (base + 0x170)
+/* ULPI viewport control bits */
+#define MX51_ULPI_WU_BIT (1 << 31)
+#define MX51_ULPI_SS_BIT (1 << 27)
+#define MX51_ULPI_RWRUN (1 << 30)
+#define MX51_ULPI_RWCTRL (1 << 29)
+
/*
* USB Registers
*/
+
struct usb_ehci {
u32 id; /* 0x000 - Identification register */
u32 hwgeneral; /* 0x004 - General hardware parameters */
@@ -241,5 +278,4 @@ struct usb_ehci {
u32 control; /* 0x500 - Control */
u8 res13[0xafc];
};
-
#endif /* _EHCI_FSL_H */
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
