This patch adds support for 88E3015 PHY for Marvell GplugD board. This patch depends on series of patch which adds support for Marvell GuruPlug-Display.
Signed-off-by: Ajay Bhargav <ajay.bhar...@einfochips.com> --- board/Marvell/gplugd/gplugd.c | 34 +++++++++++++++++++++++++++++++++- include/configs/gplugd.h | 15 ++++++++++++++- 2 files changed, 47 insertions(+), 2 deletions(-) diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c index ac5e35f..fd2e574 100644 --- a/board/Marvell/gplugd/gplugd.c +++ b/board/Marvell/gplugd/gplugd.c @@ -32,6 +32,8 @@ #include <mvmfp.h> #include <asm/arch/mfp.h> #include <asm/arch/armada100.h> +#include <asm/gpio.h> +#include <miiphy.h> #ifdef CONFIG_ARMADA100_FEC #include <net.h> @@ -83,6 +85,11 @@ int board_init(void) gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD; /* adress of boot parameters */ gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100; + /* Assert PHY_RST# */ + gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_LOW); + udelay(10); + /* Deassert PHY_RST# */ + gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH); return 0; } @@ -97,5 +104,30 @@ int board_eth_init(bd_t *bis) return armada100_fec_initialize(); } -#endif /* CONFIG_ARMADA100_FEC */ +#ifdef CONFIG_RESET_PHY_R +/* Configure and initialize PHY chip 88E3015 */ +void reset_phy(void) +{ + u16 phy_adr; + const char *name = "armd-fec0"; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xff, 0xff, (u16 *) &phy_adr)) { + printf("Err..%s could not read PHY dev address\n", + __func__); + return; + } + /* Set Ethernet LED in TX blink mode */ + miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00); + miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL); + + /* reset the phy */ + miiphy_reset(name, phy_adr); + printf("88E3015 Initialized on %s\n", name); +} +#endif /* CONFIG_RESET_PHY_R */ +#endif /* CONFIG_ARMADA100_FEC */ diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h index 7fa3020..b63ffd5 100644 --- a/include/configs/gplugd.h +++ b/include/configs/gplugd.h @@ -80,6 +80,20 @@ #define CONFIG_ROOTPATH "/tftpboot" #define CONFIG_SYS_IMG_NAME "uImage" +/* GPIO Support */ +#define CONFIG_MARVELL_GPIO + +/* PHY configuration */ +#define CONFIG_MII +#define CONFIG_CMD_MII +#define CONFIG_RESET_PHY_R +/* 88E3015 register definition */ +#define PHY_LED_PAR_SEL_REG 22 +#define PHY_LED_MAN_REG 25 +#define PHY_LED_VAL 0x5b /* LINK LED1, ACT LED2 */ +/* GPIO Configuration for PHY */ +#define CONFIG_SYS_GPIO_PHY_RST 104 /* GPIO104 */ + /* * mv-common.h should be defined after CMD configs since it used them * to enable certain macros @@ -100,4 +114,3 @@ #define CONFIG_ENV_SIZE 0x20000 /* 64k */ #endif /* __CONFIG_GPLUGD_H */ - -- 1.7.0.4 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot