The PMIC is also known as AXP819 in vendor pmu code For DCDC6, 8, 9, the underlying hardware support more than two levels voltage step tuning, but for now only first two levels are implemented in this driver, hence highest voltage will be limited at seccond level. It actual meets board requirement in current design, and we've verified it in Radxa Cubie A7A board.
Following are detail explanation of voltage tuning stpes for those DCDCs: DCDC | voltage range | units | steps | implemented 6 | 0.5 - 1.2 | 10 mV | 71 | Y . | 1.22 - 1.54 | 20 mV | 17 | Y . | 1.8 - 2.4 | 20 mV | 31 | N . | 2.44 - 2.76 | 40 mV | 9 | N -------------------------------------------------- 8/9 | 0.5 - 1.2 | 10 mV | 71 | Y . | 1.22 - 1.84 | 20 mV | 32 | Y . | 1.9 - 3.4 | 100mV | 16 | N Signed-off-by: Yixun Lan <[email protected]> --- drivers/power/pmic/axp.c | 1 + drivers/power/regulator/axp_regulator.c | 50 +++++++++++++++++++++++++++++++++ include/axp_pmic.h | 1 + 3 files changed, 52 insertions(+) diff --git a/drivers/power/pmic/axp.c b/drivers/power/pmic/axp.c index 1204ec00f8d..7d8348b0769 100644 --- a/drivers/power/pmic/axp.c +++ b/drivers/power/pmic/axp.c @@ -95,6 +95,7 @@ static const struct udevice_id axp_pmic_ids[] = { { .compatible = "x-powers,axp806", .data = AXP806_ID }, { .compatible = "x-powers,axp809", .data = AXP809_ID }, { .compatible = "x-powers,axp813", .data = AXP813_ID }, + { .compatible = "x-powers,axp318w", .data = AXP318_ID }, { } }; diff --git a/drivers/power/regulator/axp_regulator.c b/drivers/power/regulator/axp_regulator.c index 7794a4f5d92..16d3a8f7f90 100644 --- a/drivers/power/regulator/axp_regulator.c +++ b/drivers/power/regulator/axp_regulator.c @@ -189,6 +189,55 @@ static const struct axp_regulator_plat axp313_regulators[] = { { } }; + /* + * Only two level step tuning is implemented for DCDC6, 8, 9 + * so the voltage below is not support in this driver + * DCDC6: 20 (v1.8 - 2.4v), 40 (2.44v - 2.76v) + * DCDC8,9: 100 (1.9v - 3.4v) + */ +static const struct axp_regulator_plat axp318_regulators[] = { + { "dcdc1", 0x10, BIT(0), 0x12, 0x1f, 1000, 3400, 100, NA }, + { "dcdc2", 0x10, BIT(1), 0x13, 0x7f, 500, 1540, 10, 70 }, + { "dcdc3", 0x10, BIT(2), 0x14, 0x7f, 500, 1540, 10, 70 }, + { "dcdc4", 0x10, BIT(3), 0x15, 0x7f, 500, 1540, 10, 70 }, + { "dcdc5", 0x10, BIT(4), 0x16, 0x7f, 500, 1540, 10, 70 }, + { "dcdc6", 0x10, BIT(5), 0x17, 0x7f, 500, 1540, 10, 70 }, + { "dcdc7", 0x10, BIT(6), 0x18, 0x7f, 500, 1840, 10, 70 }, + { "dcdc8", 0x10, BIT(7), 0x19, 0x7f, 500, 1840, 10, 70 }, + { "dcdc9", 0x11, BIT(0), 0x1a, 0x7f, 500, 1840, 10, 70 }, + { "aldo1", 0x20, BIT(0), 0x24, 0x1f, 500, 3400, 100, NA }, + { "aldo2", 0x20, BIT(1), 0x25, 0x1f, 500, 3400, 100, NA }, + { "aldo3", 0x20, BIT(2), 0x26, 0x1f, 500, 3400, 100, NA }, + { "aldo4", 0x20, BIT(3), 0x27, 0x1f, 500, 3400, 100, NA }, + { "aldo5", 0x20, BIT(4), 0x28, 0x1f, 500, 3400, 100, NA }, + { "aldo6", 0x20, BIT(5), 0x29, 0x1f, 500, 3400, 100, NA }, + { "bldo1", 0x20, BIT(6), 0x2a, 0x1f, 500, 3400, 100, NA }, + { "bldo2", 0x20, BIT(7), 0x2b, 0x1f, 500, 3400, 100, NA }, + { "bldo3", 0x21, BIT(0), 0x2c, 0x1f, 500, 3400, 100, NA }, + { "bldo4", 0x21, BIT(1), 0x2d, 0x1f, 500, 3400, 100, NA }, + { "bldo5", 0x21, BIT(2), 0x2e, 0x1f, 500, 3400, 100, NA }, + { "cldo1", 0x21, BIT(3), 0x2f, 0x1f, 500, 3400, 100, NA }, + { "cldo2", 0x21, BIT(4), 0x30, 0x1f, 500, 3400, 100, NA }, + { "cldo3", 0x21, BIT(5), 0x31, 0x1f, 500, 3400, 100, NA }, + { "cldo4", 0x21, BIT(6), 0x32, 0x1f, 500, 3400, 100, NA }, + { "cldo5", 0x21, BIT(7), 0x33, 0x1f, 500, 3400, 100, NA }, + { "dldo1", 0x22, BIT(0), 0x34, 0x1f, 500, 3400, 100, NA }, + { "dldo2", 0x22, BIT(1), 0x35, 0x1f, 500, 3400, 100, NA }, + { "dldo3", 0x22, BIT(2), 0x36, 0x1f, 500, 3400, 100, NA }, + { "dldo4", 0x22, BIT(3), 0x37, 0x1f, 500, 3400, 100, NA }, + { "dldo5", 0x22, BIT(4), 0x38, 0x1f, 500, 3400, 100, NA }, + { "dldo6", 0x22, BIT(5), 0x39, 0x1f, 500, 3400, 100, NA }, + { "eldo1", 0x22, BIT(6), 0x3a, 0x1f, 500, 1500, 25, NA }, + { "eldo2", 0x22, BIT(7), 0x3b, 0x1f, 500, 1500, 25, NA }, + { "eldo3", 0x23, BIT(0), 0x3c, 0x1f, 500, 1500, 25, NA }, + { "eldo4", 0x23, BIT(1), 0x3d, 0x1f, 500, 1500, 25, NA }, + { "eldo5", 0x23, BIT(2), 0x3e, 0x1f, 500, 1500, 25, NA }, + { "eldo6", 0x23, BIT(3), 0x3f, 0x1f, 500, 1500, 25, NA }, + { "swout1", 0x11, BIT(3), NA, NA, NA, NA, NA, NA }, + { "swout2", 0x11, BIT(4), NA, NA, NA, NA, NA, NA }, + { } +}; + /* * The "dcdc2" regulator has another range, beyond 1.54V up to 3.4V, in * steps of 100mV. We cannot model this easily, but also don't need that, @@ -318,6 +367,7 @@ static const struct axp_regulator_plat *const axp_regulators[] = { [AXP221_ID] = axp22x_regulators, [AXP223_ID] = axp22x_regulators, [AXP313_ID] = axp313_regulators, + [AXP318_ID] = axp318_regulators, [AXP323_ID] = axp313_regulators, [AXP717_ID] = axp717_regulators, [AXP803_ID] = axp803_regulators, diff --git a/include/axp_pmic.h b/include/axp_pmic.h index 1806a7270a0..2f547da74c2 100644 --- a/include/axp_pmic.h +++ b/include/axp_pmic.h @@ -39,6 +39,7 @@ enum { AXP806_ID, AXP809_ID, AXP813_ID, + AXP318_ID, }; int axp_set_dcdc1(unsigned int mvolt); -- 2.52.0
