Hi J., On Wed, Dec 31, 2025 at 08:45:03PM +0100, J. Neuschäfer via B4 Relay wrote: > From: "J. Neuschäfer" <[email protected]> > > The X96Q is a set-top box with an H313 SoC, AXP305 PMIC, 1 or 2 GiB RAM, > 8 or 16 GiB eMMC flash, 2x USB A, Micro-SD, HDMI, Ethernet, audio/video > output, and infrared input. > > https://x96mini.com/products/x96q-tv-box-android-10-set-top-box > > This commit adds a defconfig and some documentation. The devicetree is > already in dts/upstream. > > The CONFIG_DRAM_SUNXI_* settings are chosen such that the register > values in the DRAM PHY's MMIO space are as close as possible to those > observed when booting with the preinstalled vendor U-Boot. > > --- > Signed-off-by: J. Neuschäfer <[email protected]> > --- > configs/x96q_defconfig | 46 ++++++++++++++++++++++++++++++++++ > doc/board/amediatech/index.rst | 9 +++++++ > doc/board/amediatech/x96q.rst | 57 > ++++++++++++++++++++++++++++++++++++++++++ > doc/board/index.rst | 1 + > 4 files changed, 113 insertions(+) > > diff --git a/configs/x96q_defconfig b/configs/x96q_defconfig > new file mode 100644 > index 00000000000..650fecca624 > --- /dev/null > +++ b/configs/x96q_defconfig > @@ -0,0 +1,46 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_SUNXI=y > +CONFIG_DEFAULT_DEVICE_TREE="allwinner/sun50i-h313-x96q" > +CONFIG_SPL=y > + > +CONFIG_DRAM_CLK=600 > +CONFIG_DRAM_SUNXI_DX_ODT=0x03030303 > +CONFIG_DRAM_SUNXI_DX_DRI=0x0e0e0e0e > +CONFIG_DRAM_SUNXI_CA_DRI=0x1f12 > +CONFIG_DRAM_SUNXI_TPR0=0xc0001002 > +CONFIG_DRAM_SUNXI_TPR2=0x00000100 > +CONFIG_DRAM_SUNXI_TPR10=0x002f0107 > +CONFIG_DRAM_SUNXI_TPR11=0xddddcccc > +CONFIG_DRAM_SUNXI_TPR12=0xeddc7665 > + > +CONFIG_MACH_SUN50I_H616=y > +CONFIG_SUNXI_DRAM_H616_DDR3_1333=y # DDR3 is correct, but vendor uboot > mentions 600 MHz DRAM CLK > +#CONFIG_MMC_SUNXI_SLOT_EXTRA=2 > +CONFIG_R_I2C_ENABLE=y > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set > +CONFIG_SPL_I2C=y > +CONFIG_SPL_SYS_I2C_LEGACY=y > +CONFIG_SYS_I2C_MVTWSI=y > +CONFIG_SYS_I2C_SLAVE=0x7f > +CONFIG_SYS_I2C_SPEED=400000 > +CONFIG_SUPPORT_EMMC_BOOT=y > +CONFIG_AXP305_POWER=y > +CONFIG_USB_EHCI_HCD=y > +CONFIG_USB_OHCI_HCD=y > + > +CONFIG_SPL_USE_TINY_PRINTF_POINTER_SUPPORT=y > +CONFIG_CMD_UFETCH=y > +#CONFIG_SPL_PAYLOAD="u-boot.img" > +#CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x60 > + > +CONFIG_CMD_CAT=y > + > +#CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=60 # os = 0, uboot not detected > +#CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=61 # e59f002c e5810000 f57ff04f > f57ff06f (4a0000cc) > +#CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=62 # a9431e66 a9442668 a9452e6a > a946366c (4a0002cc) > +#CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=64 # 52800000 91008081 79400025 > 34000080 (4a0006cc) > +#CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=96 # 340007c0 f9401673 eb1302ff > 54000760 (4a006acc) > +#CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=112 # f9003fe0 f94047e0 6b1c001f > 54fffcc0 (4a0162cc) > + > +CONFIG_SUN8I_EMAC=y > +CONFIG_FIT_BEST_MATCH=y > diff --git a/doc/board/amediatech/index.rst b/doc/board/amediatech/index.rst > new file mode 100644 > index 00000000000..7bc42833ec0 > --- /dev/null > +++ b/doc/board/amediatech/index.rst > @@ -0,0 +1,9 @@ > +.. SPDX-License-Identifier: GPL-2.0+ > + > +Amediatech > +========== > + > +.. toctree:: > + :maxdepth: 2 > + > + x96q > diff --git a/doc/board/amediatech/x96q.rst b/doc/board/amediatech/x96q.rst > new file mode 100644 > index 00000000000..27485c1b363 > --- /dev/null > +++ b/doc/board/amediatech/x96q.rst > @@ -0,0 +1,57 @@ > +.. SPDX-License-Identifier: GPL-2.0+
GPL-2.0+ has been deprecated as a SPDX license identifier. GPL-2.0-or-later should be used instead [1]. [1]: https://lore.kernel.org/u-boot/20251212142859.GQ303283@bill-the-cat Regards, Kuan-Wei
