On 4/24/25 05:13, Heinrich Schuchardt wrote:
> Always use ---- for the H2 level.
> 
> Signed-off-by: Heinrich Schuchardt <heinrich.schucha...@canonical.com>
> ---
> v4:
>       no change
> v3:
>       rebased upong Milk-V Mars CM removal patch
> v2:
>       new patch
> ---
>  doc/board/starfive/milk-v_mars.rst   | 10 +++++-----
>  doc/board/starfive/pine64_star64.rst | 12 ++++++------
>  doc/board/starfive/visionfive2.rst   | 10 +++++-----
>  3 files changed, 16 insertions(+), 16 deletions(-)
> 
> diff --git a/doc/board/starfive/milk-v_mars.rst 
> b/doc/board/starfive/milk-v_mars.rst
> index 554932ecfd4..aba9c9c53d4 100644
> --- a/doc/board/starfive/milk-v_mars.rst
> +++ b/doc/board/starfive/milk-v_mars.rst
> @@ -8,7 +8,7 @@ board. In U-Boot SPL the actual board is detected and the 
> device-tree patched
>  accordingly.
>  
>  Building
> -~~~~~~~~
> +--------
>  
>  1. Add the RISC-V toolchain to your PATH.
>  2. Setup ARCH & cross compilation environment variable:
> @@ -40,7 +40,7 @@ This will generate the U-Boot SPL image 
> (spl/u-boot-spl.bin.normal.out) as well
>  as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
>  
>  Device-tree selection
> -~~~~~~~~~~~~~~~~~~~~~
> +---------------------
>  
>  Depending on the board version U-Boot set variable $fdtfile to either
>  starfive/jh7110-starfive-visionfive-2-v1.2a.dtb or
> @@ -58,14 +58,14 @@ or the configuration variable CONFIG_DEFAULT_FDT_FILE can 
> be used to set to
>  provide a default value.
>  
>  Boot source selection
> -~~~~~~~~~~~~~~~~~~~~~
> +---------------------
>  
>  The board provides the DIP switches MSEL[1:0] to select the boot device out 
> of
>  SPI flash, eMMC, SD-card, UART. To select booting from SD-card set the DIP
>  switches MSEL[1:0] to 10.
>  
>  Preparing the SD-Card
> -~~~~~~~~~~~~~~~~~~~~~
> +---------------------
>  
>  The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the
>  partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free
> @@ -106,6 +106,6 @@ Copy U-Boot to the SD card
>       sudo umount /mnt
>  
>  Booting
> -~~~~~~~
> +-------
>  
>  Once you plugin the sdcard and power up, you should see the U-Boot prompt.
> diff --git a/doc/board/starfive/pine64_star64.rst 
> b/doc/board/starfive/pine64_star64.rst
> index 52e9a907917..1df4b68e4a0 100644
> --- a/doc/board/starfive/pine64_star64.rst
> +++ b/doc/board/starfive/pine64_star64.rst
> @@ -8,7 +8,7 @@ In U-Boot SPL the actual board is detected and the 
> device-tree patched
>  accordingly.
>  
>  Building
> -~~~~~~~~
> +--------
>  
>  1. Add the RISC-V toolchain to your PATH.
>  2. Setup ARCH & cross compilation environment variable:
> @@ -40,7 +40,7 @@ This will generate the U-Boot SPL image 
> (spl/u-boot-spl.bin.normal.out) as well
>  as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
>  
>  Device-tree selection
> -~~~~~~~~~~~~~~~~~~~~~
> +---------------------
>  
>  U-Boot will set variable $fdtfile to starfive/jh7110-pine64-star64.dtb.
>  
> @@ -56,7 +56,7 @@ or the configuration variable CONFIG_DEFAULT_FDT_FILE can 
> be used to set to
>  provide a default value.
>  
>  Boot source selection
> -~~~~~~~~~~~~~~~~~~~~~
> +---------------------
>  
>  Boot mode is selected by an MSEL-DIP marked S1804 and GPIO_0 position 
> adjacent
>  to the 40pin GPIO header. ON/ONKE and number markings of the MSEL-DIP are
> @@ -69,7 +69,7 @@ accurate selection.
>  + UART: 11
>  
>  Preparing the SD-Card
> -~~~~~~~~~~~~~~~~~~~~~
> +---------------------
>  
>  The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the
>  partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free
> @@ -110,12 +110,12 @@ Copy U-Boot to the SD card
>       sudo umount /mnt
>  
>  Booting
> -~~~~~~~
> +-------
>  
>  Once you plugin the sdcard and power up, you should see the U-Boot prompt.
>  
>  Serial Number and MAC address issues
> -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> +------------------------------------
>  
>  U-Boot requires valid EEPROM data to determine which board-specific fix-up to
>  apply at runtime. This affects the size of memory initialized, network mac
> diff --git a/doc/board/starfive/visionfive2.rst 
> b/doc/board/starfive/visionfive2.rst
> index 2c68df3ce4d..44e7fcb3a48 100644
> --- a/doc/board/starfive/visionfive2.rst
> +++ b/doc/board/starfive/visionfive2.rst
> @@ -36,7 +36,7 @@ Currently, the u-boot.itb is used as a dynamic of the 
> OpenSBI FW_DYNAMIC
>  firmware with the latest.
>  
>  Building
> -~~~~~~~~
> +--------
>  
>  1. Add the RISC-V toolchain to your PATH.
>  2. Setup ARCH & cross compilation environment variable:
> @@ -72,7 +72,7 @@ This will generate the U-Boot SPL image 
> (spl/u-boot-spl.bin.normal.out) as well
>  as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
>  
>  Device-tree selection
> -~~~~~~~~~~~~~~~~~~~~~
> +---------------------
>  
>  Depending on the board version U-Boot set variable $fdtfile to either
>  starfive/jh7110-starfive-visionfive-2-v1.2a.dtb or
> @@ -90,7 +90,7 @@ or the configuration variable CONFIG_DEFAULT_FDT_FILE can 
> be used to provide
>  a default value.
>  
>  Flashing
> -~~~~~~~~
> +--------
>  
>  The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the
>  partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free
> @@ -133,7 +133,7 @@ Program the SD card
>       sudo umount /mnt
>  
>  Booting
> -~~~~~~~
> +-------
>  
>  The board provides the DIP switches MSEL[1:0] to select the boot device.
>  To select booting from SD-card set the DIP switches MSEL[1:0] to 10.
> @@ -141,7 +141,7 @@ To select booting from SD-card set the DIP switches 
> MSEL[1:0] to 10.
>  Once you plugin the sdcard and power up, you should see the U-Boot prompt.
>  
>  Sample boot log from StarFive VisionFive2 board
> -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> +-----------------------------------------------
>  
>  .. code-block:: none
>  

Reviewed-by: E Shattow <e...@freeshell.de>

Reply via email to