Hi Andre,
On 03:39 Thu 17 Apr , Yixun Lan wrote:
> Hi Andre,
>
> On 01:05 Thu 17 Apr , Andre Przywara wrote:
> > Some boards with Allwinner SoCs feature a "FEL" key, sometimes also
> > labelled "uboot", which triggers the BootROM FEL mode, when pressed upon
> > power-on or reset. This allows to access the SoC's memory via USB OTG,
> > and to upload and execute code. There is a tool to upload our U-Boot image
> > and immediately boot it, when the SoC is in FEL mode.
> >
> > To mimic this convenient behaviour on boards without such a dedicated key,
> > we can query a GPIO pin very early in the SPL boot, then trigger the
> > BootROM FEL routine. There has not been much of a SoC or board setup at
> > this point, so we enter the BROM in a rather pristine state still. On
> > 64-bit SoCs the required AArch32 reset guarantees a clean CPU state anyway.
> >
> > Any GPIO can be used for that, the signal is expected to be active low,
> > consequently we enable the pull-up resistors for that pin. A board (or a
> > user) is expected to specify the GPIO name using the
> > CONFIG_SUNXI_FAKE_FEL_PIN Kconfig variable. When this variable is not set,
> > the compiler will optimise away the call.
> >
> > Call the code first thing in board_init_f(), which is the first sunxi
> > specific C routine.
> >
> > Signed-off-by: Andre Przywara <andre.przyw...@arm.com>
> > ---
> > arch/arm/mach-sunxi/Kconfig | 10 ++++++++++
> > arch/arm/mach-sunxi/board.c | 31 +++++++++++++++++++++++++++++++
> > 2 files changed, 41 insertions(+)
> >
> > diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
> > index ab432390d3c..f1cfdb548bc 100644
> > --- a/arch/arm/mach-sunxi/Kconfig
> > +++ b/arch/arm/mach-sunxi/Kconfig
> > @@ -825,6 +825,16 @@ config USB3_VBUS_PIN
> > ---help---
> > See USB1_VBUS_PIN help text.
> >
> > +config SUNXI_FAKE_FEL_PIN
> > + string "fake FEL GPIO pin"
> > + default ""
> > + ---help---
> > + Define a GPIO that shall force entering FEL mode when a button
> > + connected to this pin is pressed at boot time. This must be an
> > + active low signal, the internal pull-up resistors are activated.
> > + This takes a string in the format understood by sunxi_name_to_gpio,
> > + e.g. PH1 for pin 1 of port H.
> > +
> > config I2C0_ENABLE
> > bool "Enable I2C/TWI controller 0"
> > default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40
> > diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c
> > index 701899ee4b2..4ee0b333176 100644
> > --- a/arch/arm/mach-sunxi/board.c
> > +++ b/arch/arm/mach-sunxi/board.c
> > @@ -457,8 +457,39 @@ u32 spl_mmc_boot_mode(struct mmc *mmc, const u32
> > boot_device)
> > return result;
> > }
> >
> > +static void check_fake_fel_button(void)
> > +{
> > + u32 brom_entry = 0x20;
> > + int pin, value, mux;
> > +
> > + /* check for empty string at compile time */
> > + if (sizeof(CONFIG_SUNXI_FAKE_FEL_PIN) == sizeof(""))
> use 'sizeof("")' to express it's an empty string _explicitly_?
> otherwise, I'd prefer '0' simply (save few chars)..
>
> > + return;
> > +
> > + pin = sunxi_name_to_gpio(CONFIG_SUNXI_FAKE_FEL_PIN);
> > + if (pin < 0)
> > + return;
> > +
> > + mux = sunxi_gpio_get_cfgpin(pin);
> > + sunxi_gpio_set_cfgpin(pin, SUNXI_GPIO_INPUT);
> ...
> > + sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
> it seems this doesn't work for me.
>
> while I'm testing on A527, using pin PD6 (GPIO4_D6 in schematic)
> it goes directly to FEL mode, not sure if I setup things wrong..
> CONFIG_SUNXI_FAKE_FEL_PIN="PD6"
>
I did wrong pin mapping (not familiar with..), so switch to "PI6" (GPIO4_A5),
it works then, thanks
> > + value = gpio_get_value(pin);
> > + sunxi_gpio_set_cfgpin(pin, mux);
> > +
> > + if (value)
> > + return;
> > +
> > + /* Older SoCs maps the BootROM high in the address space. */
> > + if (fel_stash.sctlr & BIT(13))
> > + brom_entry |= 0xffff0000;
> > +
> > + return_to_fel(0, brom_entry);
> > +}
> > +
> > void board_init_f(ulong dummy)
> > {
> > + check_fake_fel_button();
> > +
> this isn't a problem, I can understand calling it here will make board
> enter FEL mode as early as possible..
>
> just wondering if better to move this function after preloader_console_init(),
> and log out a message to let user know explicitly - entering FEL mode from
> SPL..
> (I personally find it helpful)
>
> but, if you prefer not to change, then fine by me..
>
> > sunxi_sram_init();
> >
> > /* Enable non-secure access to some peripherals */
> > --
> > 2.46.3
> >
>
> --
> Yixun Lan (dlan)
--
Yixun Lan (dlan)
