Hi
On Mon, Nov 4, 2024 at 6:17 PM Adam Ford <aford...@gmail.com> wrote:
>
> On Mon, Nov 4, 2024 at 11:04 AM Michael Nazzareno Trimarchi
> <mich...@amarulasolutions.com> wrote:
> >
> > Hi Adam
> >
> > On Mon, Nov 4, 2024 at 6:01 PM Adam Ford <aford...@gmail.com> wrote:
> > >
> > > On Mon, Nov 4, 2024 at 10:29 AM Michael Nazzareno Trimarchi
> > > <mich...@amarulasolutions.com> wrote:
> > > >
> > > > Hi Adam
> > > >
> > > > On Mon, Nov 4, 2024 at 5:11 PM Adam Ford <aford...@gmail.com> wrote:
> > > > >
> > > > > On Sun, Jul 7, 2024 at 3:45 AM Michael Trimarchi
> > > > > <mich...@amarulasolutions.com> wrote:
> > > > > >
> > > > > > The osc_24m is the clock-output-name and not the one that
> > > > > > is used as internal name reference from the strcmp. The clock
> > > > > > that use osc_24m, will not be able to reparent it as they should.
> > > > > > We need anyway register the osc_24m clock fixed factor in the clock
> > > > > > tree.
> > > > > >
> > > > > > Fixes: 710c4ffb890 ("clk: imx: clk-imx8mn add gpmi nand clocks")
> > > > > > Fixes: 85b1c11989c ("clk: imx: Add ECSPI to iMX8MN")
> > > > > > Cc: Marek Vasut <ma...@denx.de>
> > > > > > Signed-off-by: Michael Trimarchi <mich...@amarulasolutions.com>
> > > > > > ---
> > > > > > drivers/clk/imx/clk-imx8mn.c | 15 +++++++++++----
> > > > > > 1 file changed, 11 insertions(+), 4 deletions(-)
> > > > > >
> > > > > > diff --git a/drivers/clk/imx/clk-imx8mn.c
> > > > > > b/drivers/clk/imx/clk-imx8mn.c
> > > > > > index ed9e16d7c1..bfd1677520 100644
> > > > > > --- a/drivers/clk/imx/clk-imx8mn.c
> > > > > > +++ b/drivers/clk/imx/clk-imx8mn.c
> > > > > > @@ -57,15 +57,15 @@ static const char *imx8mn_usdhc2_sels[] =
> > > > > > {"clock-osc-24m", "sys_pll1_400m", "sy
> > > > > > "sys_pll3_out",
> > > > > > "sys_pll1_266m", "audio_pll2_out", "sys_pll1_100m", };
> > > > > >
> > > > > > #if CONFIG_IS_ENABLED(DM_SPI)
> > > > > > -static const char *imx8mn_ecspi1_sels[] = {"osc_24m",
> > > > > > "sys_pll2_200m", "sys_pll1_40m",
> > > > > > +static const char *imx8mn_ecspi1_sels[] = {"clock-osc-24m",
> > > > > > "sys_pll2_200m", "sys_pll1_40m",
> > > > > > "sys_pll1_160m",
> > > > > > "sys_pll1_800m", "sys_pll3_out",
> > > > > > "sys_pll2_250m",
> > > > > > "audio_pll2_out", };
> > > > > >
> > > > > > -static const char *imx8mn_ecspi2_sels[] = {"osc_24m",
> > > > > > "sys_pll2_200m", "sys_pll1_40m",
> > > > > > +static const char *imx8mn_ecspi2_sels[] = {"clock-osc-24m",
> > > > > > "sys_pll2_200m", "sys_pll1_40m",
> > > > > > "sys_pll1_160m",
> > > > > > "sys_pll1_800m", "sys_pll3_out",
> > > > > > "sys_pll2_250m",
> > > > > > "audio_pll2_out", };
> > > > > >
> > > > > > -static const char *imx8mn_ecspi3_sels[] = {"osc_24m",
> > > > > > "sys_pll2_200m", "sys_pll1_40m",
> > > > > > +static const char *imx8mn_ecspi3_sels[] = {"clock-osc-24m",
> > > > > > "sys_pll2_200m", "sys_pll1_40m",
> > > > > > "sys_pll1_160m",
> > > > > > "sys_pll1_800m", "sys_pll3_out",
> > > > > > "sys_pll2_250m",
> > > > > > "audio_pll2_out", };
> > > > > > #endif
> > > > > > @@ -105,7 +105,7 @@ static const char *imx8mn_usdhc3_sels[] =
> > > > > > {"clock-osc-24m", "sys_pll1_400m", "sy
> > > > > > static const char *imx8mn_qspi_sels[] = {"clock-osc-24m",
> > > > > > "sys_pll1_400m", "sys_pll2_333m", "sys_pll2_500m",
> > > > > > "audio_pll2_out",
> > > > > > "sys_pll1_266m", "sys_pll3_out", "sys_pll1_100m", };
> > > > > >
> > > > > > -static const char * const imx8mn_nand_sels[] = {"osc_24m",
> > > > > > "sys_pll2_500m", "audio_pll1_out",
> > > > > > +static const char * const imx8mn_nand_sels[] = {"clock-osc-24m",
> > > > > > "sys_pll2_500m", "audio_pll1_out",
> > > > > > "sys_pll1_400m",
> > > > > > "audio_pll2_out", "sys_pll3_out",
> > > > > > "sys_pll2_250m",
> > > > > > "video_pll_out", };
> > > > > >
> > > > > > @@ -119,7 +119,9 @@ static const char * const imx8mn_usb_phy_sels[]
> > > > > > = {"clock-osc-24m", "sys_pll1_10
> > > > > >
> > > > > > static int imx8mn_clk_probe(struct udevice *dev)
> > > > > > {
> > > > > > + struct clk osc_24m_clk;
> > > > > > void __iomem *base;
> > > > > > + int ret;
> > > > > >
> > > > > > base = (void *)ANATOP_BASE_ADDR;
> > > > > >
> > > > > > @@ -238,6 +240,11 @@ static int imx8mn_clk_probe(struct udevice
> > > > > > *dev)
> > > > > > clk_dm(IMX8MN_SYS_PLL2_1000M,
> > > > > > imx_clk_fixed_factor("sys_pll2_1000m",
> > > > > > "sys_pll2_out", 1, 1));
> > > > > >
> > > > >
> > > > > I know it's late, but I didn't get around to testing my Nano board for
> > > > > a while. Sorry for the delayed feedback...
> > > > >
> > > > > > + ret = clk_get_by_name(dev, "osc_24m", &osc_24m_clk);
> > > > > > + if (ret)
> > > > > > + return ret;
> > > > > > + clk_dm(IMX8MN_CLK_24M, dev_get_clk_ptr(osc_24m_clk.dev));
> > > > > > +
> > > > >
> > > > > These four lines appear to have introduced a regression on the
> > > > > imx8mn-beacon board. In the SPL phase, I get an error message
> > > > > indicating it cannot find the i2c clk, then access to the PMIC fails.
> > > > > If I remove these four lines, the error message disappears, and the
> > > > > PMIC is happy again.
> > > > >
> > > > > I have confirmed that CLK, and SPL_CLK are both defined. I checked
> > > > > the u-boot-spl.dtb and it shows clock-osc-24m with clock-output-names
> > > > > = "osc_24m"
> > > > >
> > > > > I have also tried to mark the 24m clock as with bootph-pre-ram;:
> > > > > &{/clock-osc-24m} {
> > > > > bootph-pre-ram;
> > > > > };
> > > > >
> > > > > Unfortunately, nothing is helping, and I am not sure what else to try.
> > > > > clk_fixed_rate.o is built into my SPL, so I don't think it's a config
> > > > > issue. I need to the PMIC to increase the voltage since we run the
> > > > > Nano in overdrive mode to run the LPDDR4 at the highest speed.
> > > > >
> > > > > Might anyone have any suggestions?
> > > > >
> > > >
> > > > Not yet. I have a similar setup but I don't set pmic, so I think that
> > > > the symbol is not find
> > > > in SPL and it just fail clock registration. Is that possible?
> > >
> > > It does appear that the clock registration failed. Since the system
> > > does an early return, the I2C clocks among others are also not
> > > registered which appears to cause the failure.
> > >
> > > I changed the registration around a little:
> > >
> > > ret = clk_get_by_name(dev, "osc_24m", &osc_24m_clk);
> > > if (!ret)
> > > clk_dm(IMX8MN_CLK_24M, dev_get_clk_ptr(osc_24m_clk.dev));
> > >
> >
> > Seems that is not in the image spl so it can not find it. Are you sure
> > that you can inside
> > the SPL
>
> I am not sure I understand what you are asking, but the clock node
> appears in spl/u-boot-spl.dtb:
>
> clock-osc-24m {
> compatible = "fixed-clock";
> #clock-cells = <0x00>;
> clock-frequency = <0x16e3600>;
> clock-output-names = "osc_24m";
> phandle = <0x18>;
> };
>
> Since the clock-output-names is "osc_24m" I wonder if clk_get_by_name
> is the right function. Looking at other uses of this function, it
> looks like it's looking for a 'clock-names' parameter and not
> clock-output-names.
Yes, it's the right answer. That is strange because it works in uboot
image. Is the node the same in uboot-dtb?
Michael
>
> adam
> >
> > Michael
> >
> > > This method won't return prematurely, so the I2C and other clocks can
> > > be registered, and it appears to address the problem.
> > > Another alternative might be to move this clock registration until
> > > after all the rest of the clocks are done.
> > >
> > > adam
> > > >
> > > > If (ret)
> > > >
> > > > put here a print
> > > >
> > > > Michael
> > > > > adam
> > > > >
> > > > > > base = dev_read_addr_ptr(dev);
> > > > > > if (!base)
> > > > > > return -EINVAL;
> > > > > > --
> > > > > > 2.43.0
> > > > > >
> > > >
> > > >
> > > >
> > > > --
> > > > Michael Nazzareno Trimarchi
> > > > Co-Founder & Chief Executive Officer
> > > > M. +39 347 913 2170
> > > > mich...@amarulasolutions.com
> > > > __________________________________
> > > >
> > > > Amarula Solutions BV
> > > > Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
> > > > T. +31 (0)85 111 9172
> > > > i...@amarulasolutions.com
> > > > www.amarulasolutions.com
> >
> >
> >
> > --
> > Michael Nazzareno Trimarchi
> > Co-Founder & Chief Executive Officer
> > M. +39 347 913 2170
> > mich...@amarulasolutions.com
> > __________________________________
> >
> > Amarula Solutions BV
> > Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
> > T. +31 (0)85 111 9172
> > i...@amarulasolutions.com
> > www.amarulasolutions.com
--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
mich...@amarulasolutions.com
__________________________________
Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
i...@amarulasolutions.com
www.amarulasolutions.com
