Hello Simon, Am Thu, Sep 19, 2024 at 05:14:22PM +0200 schrieb Simon Glass: > Move this section of the README into doc/ with some minor updates to > mention SPL and user lower-case hex.
Maybe try not to rewrap unchanged paragraphs, so `git show --color-moved` can detect those as just moved? > Signed-off-by: Simon Glass <s...@chromium.org> > --- > > README | 45 ------------------------------------------ > doc/develop/index.rst | 1 + > doc/develop/memory.rst | 45 ++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 46 insertions(+), 45 deletions(-) > create mode 100644 doc/develop/memory.rst > > diff --git a/README b/README > index 4be1e8c22a0..d73042406b6 100644 > --- a/README > +++ b/README > @@ -2516,51 +2516,6 @@ On RISC-V, the following registers are used: > > ==> U-Boot will use gp to hold a pointer to the global data > > -Memory Management: > ------------------- > - > -U-Boot runs in system state and uses physical addresses, i.e. the > -MMU is not used either for address mapping nor for memory protection. > - > -The available memory is mapped to fixed addresses using the memory > -controller. In this process, a contiguous block is formed for each > -memory type (Flash, SDRAM, SRAM), even when it consists of several > -physical memory banks. > - > -U-Boot is installed in the first 128 kB of the first Flash bank (on > -TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After > -booting and sizing and initializing DRAM, the code relocates itself > -to the upper end of DRAM. Immediately below the U-Boot code some > -memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN > -configuration setting]. Below that, a structure with global Board > -Info data is placed, followed by the stack (growing downward). > - > -Additionally, some exception handler code is copied to the low 8 kB > -of DRAM (0x00000000 ... 0x00001FFF). > - > -So a typical memory configuration with 16 MB of DRAM could look like > -this: > - > - 0x0000 0000 Exception Vector code > - : > - 0x0000 1FFF > - 0x0000 2000 Free for Application Use > - : > - : > - > - : > - : > - 0x00FB FF20 Monitor Stack (Growing downward) > - 0x00FB FFAC Board Info Data and permanent copy of global data > - 0x00FC 0000 Malloc Arena > - : > - 0x00FD FFFF > - 0x00FE 0000 RAM Copy of Monitor Code > - ... eventually: LCD or video framebuffer > - ... eventually: pRAM (Protected RAM - unchanged by reset) > - 0x00FF FFFF [End of RAM] > - > - > System Initialization: > ---------------------- > > diff --git a/doc/develop/index.rst b/doc/develop/index.rst > index 0d0e60ab56c..cbea38d4323 100644 > --- a/doc/develop/index.rst > +++ b/doc/develop/index.rst > @@ -13,6 +13,7 @@ General > codingstyle > designprinciples > docstyle > + memory > patman > process > release_cycle > diff --git a/doc/develop/memory.rst b/doc/develop/memory.rst > new file mode 100644 > index 00000000000..fa1ae5e97ed > --- /dev/null > +++ b/doc/develop/memory.rst > @@ -0,0 +1,45 @@ > +.. SPDX-License-Identifier: GPL-2.0+: > + > +Memory Management > +----------------- > + > +U-Boot runs in system state and uses physical addresses, i.e. the > +MMU is not used either for address mapping nor for memory protection. > + > +The available memory is mapped to fixed addresses using the > +memory-controller. In this process, a contiguous block is formed for each > +memory type (Flash, SDRAM, SRAM), even when it consists of several > +physical-memory banks. > + > +U-Boot is installed in XIP flash memory, or may be loaded into a lower > region of > +RAM by a secondary program loader (SPL). After > +booting and sizing and initialising DRAM, the code relocates itself > +to the upper end of DRAM. Immediately below the U-Boot code some > +memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN > +configuration setting]. Below that, a structure with global Board-Info > +data is placed, followed by the stack (growing downward). > + > +Additionally, some exception handler code may be copied to the low 8 kB > +of DRAM (0x00000000 ... 0x00001fff). > + > +So a typical memory configuration with 16 MB of DRAM could look like > +this:: > + > + 0x0000 0000 Exception Vector code > + : > + 0x0000 1fff > + 0x0000 2000 Free for Application Use > + : > + : > + > + : > + : > + 0x00fb ff20 Monitor Stack (Growing downward) > + 0x00fb ffac Board Info Data and permanent copy of global data > + 0x00fc 0000 Malloc Arena Arena? `make htmldocs` runs fine, page looks okay, thus: Acked-by: Alexander Dahl <a...@thorsis.com> Greets Alex > + : > + 0x00fd ffff > + 0x00fe 0000 RAM Copy of Monitor Code > + ... eventually: LCD or video framebuffer > + ... eventually: pRAM (Protected RAM - unchanged by reset) > + 0x00ff ffff [End of RAM] > -- > 2.43.0 >
