Hello Tom! This patch set is hanging in patchwork for 3 month without any comments. If no one has anything to say, may you pick it into master?
Best regards, Svyatoslav R. вт, 23 січ. 2024 р. о 19:17 Svyatoslav Ryhel <clamo...@gmail.com> пише: > > T114 is not that different from T30 and all T30 drivers will work > on T114 as well with some adjustments. > > Patches propose general improvements for existing Tegra DC and DSI > drivers as well Tegra 114 video support (experimentl). > > Commits pass buildman for tegra. > > --- > Changes from v5: > - backlight enable moved to the last step of setup for DSI > - parameterized V- and H-sync polarities > - added framebuffer clearing on probe to avoid glitches > - backlight enable moved after DC is fully configured > - fixed printing framebuffer pointer instead of address > - moved scdiv calculation to tegra DSI if it is used > > Changes from v4: > - fixed typo in max rate to be divided (400KHz > 400MHz) > > Changes from v3: > - fixed the clock divider calculation if PLLD/D2 is used > - removed unnecessary pre-configuration > - set correct video FIFO depth for DSI > > Changes from v2: > - fixed image distortion on devices with 180deg rotation > > Changes from v1: > - reworked patchset entirely > - diverged DC configuration per-SOC > - consolidated dc headers from different SOC gen > - initial support of DC detection (tegra has 2 DC) > - added PLLD2 support, resets and powergating > - added T114+ MIPI calibration > - added DSI detection (tegra has 2 DSI) and resets > --- > > Jonas Schwöbel (6): > video: tegra20: dc: fix printing of framebuffer address > video: tegra20: dc: enable backlight after DC is configured > video: tegra20: dc: clean framebuffer memory block > video: tegra20: dsi: remove pre-configuration > video: tegra20: dsi: set correct fifo depth > video: tegra20: dsi: use set_backlight for backlight only > > Svyatoslav Ryhel (12): > video: tegra20: dc: diverge DC per-SOC > video: tegra20: dc: fix image shift on rotated panels > video: tegra20: consolidate DC header > video: tegra20: dc: pass DC id to internal devices > video: tegra20: dc: add PLLD2 parent support > video: tegra20: dc: add reset support > video: tegra20: dc: add powergate > video: tegra20: dc: configure behavior if PLLD/D2 is used > video: tegra20: dc: parameterize V- and H-sync polarities > video: tegra20: add MIPI calibration driver > video: tegra20: dsi: add T114 support > video: tegra20: dsi: add reset support > > arch/arm/dts/tegra114-u-boot.dtsi | 13 + > arch/arm/dts/tegra114.dtsi | 4 +- > arch/arm/dts/tegra30-u-boot.dtsi | 4 + > arch/arm/dts/tegra30.dtsi | 2 +- > arch/arm/include/asm/arch-tegra/dc.h | 13 +- > arch/arm/include/asm/arch-tegra114/pwm.h | 13 + > arch/arm/include/asm/arch-tegra20/display.h | 28 -- > arch/arm/include/asm/arch-tegra30/display.h | 28 -- > drivers/video/tegra20/Makefile | 2 +- > drivers/video/tegra20/tegra-dc.c | 239 +++++++++++++----- > drivers/video/tegra20/tegra-dc.h | 45 ++++ > drivers/video/tegra20/tegra-dsi.c | 122 ++++++++- > .../video/tegra20/tegra-dsi.h | 24 +- > drivers/video/tegra20/tegra-mipi.c | 188 ++++++++++++++ > drivers/video/tegra20/tegra-pwm-backlight.c | 3 +- > 15 files changed, 583 insertions(+), 145 deletions(-) > create mode 100644 arch/arm/include/asm/arch-tegra114/pwm.h > delete mode 100644 arch/arm/include/asm/arch-tegra20/display.h > delete mode 100644 arch/arm/include/asm/arch-tegra30/display.h > create mode 100644 drivers/video/tegra20/tegra-dc.h > rename arch/arm/include/asm/arch-tegra30/dsi.h => > drivers/video/tegra20/tegra-dsi.h (90%) > create mode 100644 drivers/video/tegra20/tegra-mipi.c > > -- > 2.40.1 >
