With the stack and text base used by U-Boot SPL and proper on RK3328
there is a high likelihood of overlapping when U-Boot proper + FDT nears
or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3328:
[ 0, 256K) - SPL binary
[ 256K, 2M) - TF-A / reserved
[ 2M, +X) - U-Boot proper binary (TEXT_BASE)
[ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[ -8K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[ -X, 4M) - SPL pre-reloc stack (SPL_STACK)
[ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
[ 32M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [2M, 4M-8K) with this layout.
However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is
restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to
fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman <jo...@kwiboo.se>
---
arch/arm/mach-rockchip/rk3328/Kconfig | 11 ++++-------
configs/evb-rk3328_defconfig | 17 -----------------
configs/nanopi-r2c-plus-rk3328_defconfig | 15 ---------------
configs/nanopi-r2c-rk3328_defconfig | 15 ---------------
configs/nanopi-r2s-rk3328_defconfig | 15 ---------------
configs/orangepi-r1-plus-lts-rk3328_defconfig | 15 ---------------
configs/orangepi-r1-plus-rk3328_defconfig | 15 ---------------
configs/roc-cc-rk3328_defconfig | 15 ---------------
configs/rock-pi-e-rk3328_defconfig | 17 -----------------
configs/rock64-rk3328_defconfig | 15 ---------------
10 files changed, 4 insertions(+), 146 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3328/Kconfig
b/arch/arm/mach-rockchip/rk3328/Kconfig
index d5cb649ae6ba..70770da5fdf2 100644
--- a/arch/arm/mach-rockchip/rk3328/Kconfig
+++ b/arch/arm/mach-rockchip/rk3328/Kconfig
@@ -21,13 +21,7 @@ config ROCKCHIP_STIMER_BASE
config SYS_SOC
default "rk3328"
-config SYS_MALLOC_F_LEN
- default 0x2000
-
-config SPL_LIBCOMMON_SUPPORT
- default y
-
-config SPL_LIBGENERIC_SUPPORT
+config ROCKCHIP_COMMON_STACK_ADDR
default y
config TPL_LDSCRIPT
@@ -39,6 +33,9 @@ config TPL_TEXT_BASE
config TPL_STACK
default 0xff098000
+config TPL_SYS_MALLOC_F_LEN
+ default 0x800
+
source "board/rockchip/evb_rk3328/Kconfig"
endif
diff --git a/configs/evb-rk3328_defconfig b/configs/evb-rk3328_defconfig
index da422c8ba4e7..4fa8a7d365a4 100644
--- a/configs/evb-rk3328_defconfig
+++ b/configs/evb-rk3328_defconfig
@@ -2,22 +2,12 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-evb"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x4000000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
-CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SYS_LOAD_ADDR=0x800800
@@ -33,16 +23,9 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-evb.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/nanopi-r2c-plus-rk3328_defconfig
b/configs/nanopi-r2c-plus-rk3328_defconfig
index 25850328f8b8..5302fd91a0f5 100644
--- a/configs/nanopi-r2c-plus-rk3328_defconfig
+++ b/configs/nanopi-r2c-plus-rk3328_defconfig
@@ -2,22 +2,13 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c-plus"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x600000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SYS_LOAD_ADDR=0x800800
@@ -33,16 +24,10 @@
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c-plus.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
CONFIG_SPL_POWER=y
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/nanopi-r2c-rk3328_defconfig
b/configs/nanopi-r2c-rk3328_defconfig
index a4cb148246e6..5a722c182631 100644
--- a/configs/nanopi-r2c-rk3328_defconfig
+++ b/configs/nanopi-r2c-rk3328_defconfig
@@ -2,22 +2,13 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x600000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SYS_LOAD_ADDR=0x800800
@@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
CONFIG_SPL_POWER=y
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/nanopi-r2s-rk3328_defconfig
b/configs/nanopi-r2s-rk3328_defconfig
index c5d13788528b..985d02475ece 100644
--- a/configs/nanopi-r2s-rk3328_defconfig
+++ b/configs/nanopi-r2s-rk3328_defconfig
@@ -2,22 +2,13 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2s"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x600000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SYS_LOAD_ADDR=0x800800
@@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2s.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
CONFIG_SPL_POWER=y
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/orangepi-r1-plus-lts-rk3328_defconfig
b/configs/orangepi-r1-plus-lts-rk3328_defconfig
index 6360f5df3864..e9f7a1306923 100644
--- a/configs/orangepi-r1-plus-lts-rk3328_defconfig
+++ b/configs/orangepi-r1-plus-lts-rk3328_defconfig
@@ -2,23 +2,14 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus-lts"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
CONFIG_ROCKCHIP_SPI_IMAGE=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x600000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
@@ -36,18 +27,12 @@
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus-lts.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
CONFIG_SPL_POWER=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/orangepi-r1-plus-rk3328_defconfig
b/configs/orangepi-r1-plus-rk3328_defconfig
index 9473a08fe20d..6019f33ae3f5 100644
--- a/configs/orangepi-r1-plus-rk3328_defconfig
+++ b/configs/orangepi-r1-plus-rk3328_defconfig
@@ -2,23 +2,14 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
CONFIG_ROCKCHIP_SPI_IMAGE=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x600000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
@@ -36,18 +27,12 @@
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
CONFIG_SPL_POWER=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/roc-cc-rk3328_defconfig b/configs/roc-cc-rk3328_defconfig
index c66b1ccba267..191dbff928bb 100644
--- a/configs/roc-cc-rk3328_defconfig
+++ b/configs/roc-cc-rk3328_defconfig
@@ -2,22 +2,13 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-roc-cc"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x600000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SYS_LOAD_ADDR=0x800800
@@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-roc-cc.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
CONFIG_SPL_POWER=y
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/rock-pi-e-rk3328_defconfig
b/configs/rock-pi-e-rk3328_defconfig
index 275ffc3ed8f4..e4f2123e0b17 100644
--- a/configs/rock-pi-e-rk3328_defconfig
+++ b/configs/rock-pi-e-rk3328_defconfig
@@ -2,23 +2,13 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock-pi-e"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x4000000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
-CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SYS_LOAD_ADDR=0x800800
@@ -34,17 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock-pi-e.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
CONFIG_SPL_POWER=y
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
diff --git a/configs/rock64-rk3328_defconfig b/configs/rock64-rk3328_defconfig
index 1cb4e6777d45..f38431891bf8 100644
--- a/configs/rock64-rk3328_defconfig
+++ b/configs/rock64-rk3328_defconfig
@@ -2,23 +2,14 @@ CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_COUNTER_FREQUENCY=24000000
CONFIG_ARCH_ROCKCHIP=y
-CONFIG_TEXT_BASE=0x00200000
CONFIG_SPL_GPIO=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_ENV_OFFSET=0x3F8000
CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock64"
CONFIG_DM_RESET=y
CONFIG_ROCKCHIP_RK3328=y
-CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
CONFIG_ROCKCHIP_SPI_IMAGE=y
-CONFIG_TPL_LIBCOMMON_SUPPORT=y
-CONFIG_TPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_STACK_R_ADDR=0x600000
-CONFIG_SPL_STACK=0x400000
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
CONFIG_DEBUG_UART_BASE=0xFF130000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
@@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock64.dtb"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x7f8000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x2000000
-CONFIG_SPL_BSS_MAX_SIZE=0x2000
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK_R=y
CONFIG_SPL_POWER=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
CONFIG_SPL_ATF=y
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-CONFIG_TPL_SYS_MALLOC_SIMPLE=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
