On Thursday 27 April 2023 10:56:17 Stefan Roese wrote: > Hi Pali, > > On 4/27/23 01:44, Pali Rohár wrote: > > On Thursday 13 April 2023 22:43:25 Martin Rowe wrote: > > > On Thu, 13 Apr 2023 at 20:58, Pali Rohár <p...@kernel.org> wrote: > > > > > > > > BootROM and neither SPL does not use eMMC boot acknowledgement or boot > > > > enable bits in EXT_CSD_PART_CONF eMMC register. And also fixed SATA disk > > > > sector 0x141 is not used at all. > > > > > > > > Signed-off-by: Pali Rohár <p...@kernel.org> > > > > > > SPL successfully loads u-boot from the same partition as SPL. SD card > > > and UART continue to boot. > > > > > > Thanks Pali! > > > > > > Tested-by: Martin Rowe <martin.p.r...@gmail.com> > > > > Ok, is something more needed for this patch series? > > Unfortunately yes. As at least this board breaks with this patchset > added: > > $ make sama5d2_icp_mmc_defconfig > $ make -sj > /opt/kernel.org/gcc-12.2.0-nolibc/arm-linux-gnueabi/bin/arm-linux-gnueabi-ld.bfd: > u-boot-spl section `__u_boot_list' will not fit in region `.sram' > /opt/kernel.org/gcc-12.2.0-nolibc/arm-linux-gnueabi/bin/arm-linux-gnueabi-ld.bfd: > region `.sram' overflowed by 32 bytes > make[1]: *** [scripts/Makefile.spl:527: spl/u-boot-spl] Error 1 > make: *** [Makefile:2049: spl/u-boot-spl] Error 2 > > So CI build fails and I can't send a pull request. I'm sending a patch > though, to fix this image overflow by enabling LTO. Stay tuned...
I see... LTO helped. So can be this patch series now applied? > Thanks, > Stefan > > > > > --- > > > > board/solidrun/clearfog/README | 20 ++++++++++---------- > > > > 1 file changed, 10 insertions(+), 10 deletions(-) > > > > > > > > diff --git a/board/solidrun/clearfog/README > > > > b/board/solidrun/clearfog/README > > > > index ed4a712c5aa2..c86b37061a30 100644 > > > > --- a/board/solidrun/clearfog/README > > > > +++ b/board/solidrun/clearfog/README > > > > @@ -1,7 +1,7 @@ > > > > Update from original Marvell U-Boot to mainline U-Boot: > > > > ------------------------------------------------------- > > > > > > > > -Generate the U-Boot image with these commands: > > > > +Generate the U-Boot image for eMMC/SD with these commands: > > > > > > > > $ make clearfog_defconfig > > > > $ make > > > > @@ -9,7 +9,7 @@ $ make > > > > The resulting image including the SPL binary with the > > > > full DDR setup is "u-boot-with-spl.kwb". > > > > > > > > -Now all you need to do is copy this image on a SD card. > > > > +Now all you need to do is copy this image on a SD card's sector 1. > > > > For example with this command: > > > > > > > > $ sudo dd if=u-boot-with-spl.kwb of=/dev/sdX bs=512 seek=1 > > > > @@ -20,12 +20,6 @@ of "/dev/sdX" here! > > > > Install U-Boot on eMMC: > > > > ----------------------- > > > > > > > > -To make SPL load the main U-Boot image from the eMMC boot partition > > > > enable > > > > -eMMC boot acknowledgement and boot partition with the following U-Boot > > > > -command: > > > > - > > > > - mmc partconf 0 1 1 0 > > > > - > > > > Install U-Boot on eMMC boot partition from Linux running on Clearfog: > > > > > > > > echo 0 > /sys/block/mmcblk0boot0/force_ro > > > > @@ -37,8 +31,14 @@ Consider initial boot from UART (see below). > > > > Install U-Boot on SATA: > > > > ----------------------- > > > > > > > > -When loading the main U-Boot image from raw SATA sector, set > > > > -CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR to 0x141. > > > > +Generate the U-Boot image for SATA with these commands: > > > > + > > > > +$ make clearfog_sata_defconfig > > > > +$ make > > > > + > > > > +Copy image on a SATA disk's sector 1: > > > > + > > > > +$ sudo dd if=u-boot-with-spl.kwb of=/dev/sdX bs=512 seek=1 > > > > > > > > Boot selection: > > > > --------------- > > > > -- > > > > 2.20.1 > > > > > > Viele Grüße, > Stefan Roese > > -- > DENX Software Engineering GmbH, Managing Director: Erika Unter > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany > Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: s...@denx.de
