Hi Pali, On Mon, Jan 30, 2023 at 12:11 PM Pali Rohár <p...@kernel.org> wrote: > > On Monday 28 March 2022 09:57:41 Hajo Noerenberg wrote: > > Hi Tony, > > > > thank you very much for your help. I will integrate the changes and > > resubmit the patch when Tom's work on CONFIG_RESET_PHY_R is done. If you or > > others have further improvements in the meantime, please let me know. > > Hello! I would like to ask, is there any progress on this? > Or is nas440 board already ready for merging?
I have not heard from Hajo since then. Tony > > I wonder if it would be a good idea to submit adding the PCI-ids for the > > 88SE6121 controller (drivers/ata/ahci-pci.c) as a separate patch. The > > controller is not specific to the NAS440, to my knowledge it is also used > > on the Iomega ix4-200d for example. > > > > Thanks, > > Hajo > > > > > > Am 26.03.2022 um 02:33 schrieb Tony Dinh: > > > Hi Hajo, > > > > > > General comments: > > > > > > - You're missing a file in this patch set: arch/arm/mach-kirkwood/Kconfig. > > > - There are numerous style problems. You should run > > > scripts/checkpatch.pl on each file to cleanup. Also look into using > > > patman to create patches, and possibly sending patches too. It takes a > > > bit of getting used to, but patman is very useful. Especially sending > > > patch series and revisions. > > > - Please use the canonical form for nas440_defconfig. > > > make nas440_deconfig > > > make savedefconfig > > > mv defconfig configs/nas440_defconfig > > > > > > - This is a board that is not yet supported in mainline Linux (i.e. > > > there is no legacy dependency). Thus, we don't want to use ATAGS. > > > Remove: > > >>>> +CONFIG_SUPPORT_PASSING_ATAGS=y > > >>>> +CONFIG_CMDLINE_TAG=y > > >>>> +CONFIG_INITRD_TAG=y > > > - This patch will need a revision after Tom's patch is merged to master. > > > See: > > > https://lists.denx.de/pipermail/u-boot/2022-March/478823.html > > > > > > Thanks, > > > Tony > > > > > > On Thu, Mar 24, 2022 at 3:04 PM Tony Dinh <mibo...@gmail.com> wrote: > > >> > > >> Hi Hajo, > > >> > > >> I've added Stefan. > > >> > > >> When you send patches for Kirkwood or other Marvell boards, please > > >> also send it directly to Stefan (Stefan is the maintainer of Marvell > > >> u-boots). > > >> > > >> Tony > > >> > > >> On Thu, Mar 24, 2022 at 3:11 AM Pali Rohár <p...@kernel.org> wrote: > > >>> > > >>> Hello! > > >>> > > >>> On Thursday 24 March 2022 10:55:38 Hajo Noerenberg wrote: > > >>>> This adds support for the Seagate Blackarmor NAS440 (4-bay Kirkwood > > >>>> NAS box). > > >>>> > > >>>> Does it make sense to include support for a 10+ year old device? > > >>> > > >>> If these old devices are still in use and you would like to maintain > > >>> this support then I think that there is no issue with it. > > >>> > > >>>> If yes, I would be willing to discuss and finalize this patch. If no, > > >>>> it will be archived here for the public, which is fine with me. > > >>>> > > >>>> For the NAS440 is the something special that hard disk drives 1 and 2 > > >>>> are connected to a 88SE6121 SATA-II controller, which is connected via > > >>>> PCIe. Hard disk drives 3 and 4 are directly connected to the 88F6281 > > >>>> SoC. > > >>>> > > >>>> - Add NAS440 dtb and associated files/configs > > >>>> * Includes support for HD44780 front LCD > > >>>> * Includes support for device LEDs (via 74AHC164 shift register) > > >>>> - Add Marvell 88SE6121 AHCI support. Thanks to Pali Rohár for recently > > >>>> adding the necessary Kirkwood PCIe driver. It works :) > > >>> > > >>> Perfect! > > >>> > > >>>> - Tested with my NAS440 hardware: ETH/USB/SATA/AHCI-SCSI/GPIO/LCD/LEDs > > >>>> ok > > >>>> > > >>>> As far as I can see this fully implements the support for this board > > >>>> within U-Boot. With the Linux kernel however there are problems, the > > >>>> kernel AHCI driver fails with "failed to IDENTIFY" messages for the > > >>>> 88SE6121 drive ports, which I could not solve yet despite comparison > > >>>> with the GPL sources from Seagate. > > >>>> > > >>>> Note: I am collecting various information and patches for the family > > >>>> of Blackarmor NAS boards at > > >>>> https://github.com/hn/seagate-blackarmor-nas > > >>>> > > >>>> Hajo > > >>>> > > >>>> > > >>>> --- > > >>>> arch/arm/dts/kirkwood-blackarmor-nas440.dts | 166 +++++++++ > > >>>> board/Seagate/nas440/Kconfig | 12 + > > >>>> board/Seagate/nas440/MAINTAINERS | 7 + > > >>>> board/Seagate/nas440/Makefile | 7 + > > >>>> board/Seagate/nas440/kwbimage.cfg | 156 ++++++++ > > >>>> board/Seagate/nas440/nas440.c | 378 ++++++++++++++++++++ > > >>>> configs/nas440_defconfig | 89 +++++ > > >>>> drivers/ata/ahci-pci.c | 1 + > > >>>> include/configs/nas440.h | 50 +++ > > >>>> 9 files changed, 866 insertions(+) > > >>>> create mode 100644 arch/arm/dts/kirkwood-blackarmor-nas440.dts > > >>>> create mode 100644 board/Seagate/nas440/Kconfig > > >>>> create mode 100644 board/Seagate/nas440/MAINTAINERS > > >>>> create mode 100644 board/Seagate/nas440/Makefile > > >>>> create mode 100644 board/Seagate/nas440/kwbimage.cfg > > >>>> create mode 100644 board/Seagate/nas440/nas440.c > > >>>> create mode 100644 configs/nas440_defconfig > > >>>> create mode 100644 include/configs/nas440.h > > >>>> > > >>>> diff --git a/arch/arm/dts/kirkwood-blackarmor-nas440.dts > > >>>> b/arch/arm/dts/kirkwood-blackarmor-nas440.dts > > >>>> new file mode 100644 > > >>>> index 0000000000..60e3fe6f0d > > >>>> --- /dev/null > > >>>> +++ b/arch/arm/dts/kirkwood-blackarmor-nas440.dts > > >>>> @@ -0,0 +1,166 @@ > > >>>> +// SPDX-License-Identifier: GPL-2.0+ > > >>>> +/* > > >>>> + * Device Tree file for Seagate Blackarmor NAS440 > > >>>> + * > > >>>> + * Copyright (C) 2021 Hajo Noerenberg <www.github.com/hn> > > >>>> + * Copyright (C) 2015 Andreas Fischer <a...@bantux.org> > > >>>> + * Copyright (C) 2014 Evgeni Dobrev <evg...@studio-punkt.com> > > >>>> + */ > > >>>> + > > >>>> +/dts-v1/; > > >>>> + > > >>>> +#include <dt-bindings/gpio/gpio.h> > > >>>> +#include <dt-bindings/input/input.h> > > >>>> +#include "kirkwood.dtsi" > > >>>> +#include "kirkwood-6281.dtsi" > > >>>> + > > >>>> +/ { > > >>>> + model = "Seagate Blackarmor NAS440"; > > >>>> + compatible = > > >>>> "seagate,blackarmor-nas440","marvell,kirkwood-88f6281", > > >>>> + "marvell,kirkwood"; > > >>>> + > > >>>> + memory { /* 256 MB */ > > >>>> + device_type = "memory"; > > >>>> + reg = <0x00000000 0x10000000>; > > >>>> + }; > > >>>> + > > >>>> + chosen { > > >>>> + bootargs = "console=ttyS0,115200n8"; > > >>>> + stdout-path = &uart0; > > >>>> + }; > > >>>> + > > >>>> + gpio_poweroff { > > >>>> + compatible = "gpio-poweroff"; > > >>>> + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* > > >>>> GPIO1-16 is MPP48 */ > > >>>> + }; > > >>>> + > > >>>> + gpio_keys { > > >>>> + compatible = "gpio-keys"; > > >>>> + > > >>>> + reset { > > >>>> + label = "Reset"; > > >>>> + linux,code = <KEY_POWER>; > > >>>> + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; > > >>>> + }; > > >>>> + > > >>>> + button { > > >>>> + label = "Power"; > > >>>> + linux,code = <KEY_SLEEP>; > > >>>> + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; /* > > >>>> GPIO1-17 is MPP49 */ > > >>>> + }; > > >>>> + }; > > >>>> + > > >>>> + regulators { > > >>>> + compatible = "simple-bus"; > > >>>> + #address-cells = <1>; > > >>>> + #size-cells = <0>; > > >>>> + pinctrl-0 = <&pmx_power_socsata>; > > >>>> + pinctrl-names = "default"; > > >>>> + > > >>>> + socsata_power: regulator@1 { > > >>>> + compatible = "regulator-fixed"; > > >>>> + reg = <1>; > > >>>> + regulator-name = "SoC SATA Power"; > > >>>> + regulator-min-microvolt = <12000000>; > > >>>> + regulator-max-microvolt = <12000000>; > > >>>> + enable-active-high; > > >>>> + regulator-always-on; > > >>>> + regulator-boot-on; > > >>>> + gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>; > > >>>> + }; > > >>>> + }; > > >>>> +}; > > >>>> + > > >>>> +/* > > >>>> + * Serial port routed to connector CN4 > > >>>> + * > > >>>> + * pin 1 - TX (CPU's TX) > > >>>> + * pin 4 - RX (CPU's RX) > > >>>> + * pin 6 - GND > > >>>> + */ > > >>>> +&uart0 { > > >>>> + status = "okay"; > > >>>> +}; > > >>>> + > > >>>> +&pinctrl { > > >>>> + pinctrl-0 = <&pmx_button_reset &pmx_button_power>; > > >>>> + pinctrl-names = "default"; > > >>>> + > > >>>> + pmx_act_sata0: pmx-act-sata0 { > > >>>> + marvell,pins = "mpp15"; > > >>>> + marvell,function = "sata0"; > > >>>> + }; > > >>>> + > > >>>> + pmx_act_sata1: pmx-act-sata1 { > > >>>> + marvell,pins = "mpp16"; > > >>>> + marvell,function = "sata1"; > > >>>> + }; > > >>>> + > > >>>> + pmx_power_socsata: pmx-power-socsata { > > >>>> + marvell,pins = "mpp28"; > > >>>> + marvell,function = "gpio"; > > >>>> + }; > > >>>> + > > >>>> + pmx_button_reset: pmx-button-reset { > > >>>> + marvell,pins = "mpp29"; > > >>>> + marvell,function = "gpio"; > > >>>> + }; > > >>>> + > > >>>> + pmx_button_power: pmx-button-power { > > >>>> + marvell,pins = "mpp49"; > > >>>> + marvell,function = "gpio"; > > >>>> + }; > > >>>> +}; > > >>>> + > > >>>> +&sata { > > >>>> + status = "okay"; > > >>>> + nr-ports = <2>; > > >>>> +}; > > >>>> + > > >>>> +&pciec { > > >>>> + status = "okay"; > > >>>> +}; > > >>>> + > > >>>> +&pcie0 { > > >>>> + status = "okay"; > > >>>> +}; > > >>>> + > > >>>> +&i2c0 { > > >>>> + status = "okay"; > > >>>> + > > >>>> + adt7473: thermal@2e { > > >>>> + compatible = "adi,adt7473"; > > >>>> + reg = <0x2e>; > > >>>> + }; > > >>>> +}; > > >>>> + > > >>>> +&nand { > > >>>> + status = "okay"; > > >>>> +}; > > >>>> + > > >>>> +&mdio { > > >>>> + status = "okay"; > > >>>> + > > >>>> + ethphy0: ethernet-phy@8 { > > >>>> + reg = <8>; > > >>>> + }; > > >>>> + ethphy1: ethernet-phy@9 { > > >>>> + reg = <9>; > > >>>> + }; > > >>>> +}; > > >>>> + > > >>>> +ð0 { > > >>>> + status = "okay"; > > >>>> + > > >>>> + ethernet0-port@0 { > > >>>> + phy-handle = <ðphy0>; > > >>>> + }; > > >>>> +}; > > >>>> + > > >>>> +ð1 { > > >>>> + status = "okay"; > > >>>> + > > >>>> + ethernet1-port@0 { > > >>>> + phy-handle = <ðphy1>; > > >>>> + }; > > >>>> +}; > > >>>> diff --git a/board/Seagate/nas440/Kconfig > > >>>> b/board/Seagate/nas440/Kconfig > > >>>> new file mode 100644 > > >>>> index 0000000000..3f93d75cd4 > > >>>> --- /dev/null > > >>>> +++ b/board/Seagate/nas440/Kconfig > > >>>> @@ -0,0 +1,12 @@ > > >>>> +if TARGET_NAS440 > > >>>> + > > >>>> +config SYS_BOARD > > >>>> + default "nas440" > > >>>> + > > >>>> +config SYS_VENDOR > > >>>> + default "Seagate" > > >>>> + > > >>>> +config SYS_CONFIG_NAME > > >>>> + default "nas440" > > >>>> + > > >>>> +endif > > >>>> diff --git a/board/Seagate/nas440/MAINTAINERS > > >>>> b/board/Seagate/nas440/MAINTAINERS > > >>>> new file mode 100644 > > >>>> index 0000000000..dcea1316c5 > > >>>> --- /dev/null > > >>>> +++ b/board/Seagate/nas440/MAINTAINERS > > >>>> @@ -0,0 +1,7 @@ > > >>>> +NAS440 BOARD > > >>>> +M: Hajo Noerenberg <hajo-ub...@noerenberg.de> > > >>>> +S: Maintained > > >>>> +F: board/Seagate/nas440/ > > >>>> +F: include/configs/nas440.h > > >>>> +F: configs/nas440_defconfig > > >>>> +F: arch/arm/dts/kirkwood-blackarmor-nas440.dts > > >>>> diff --git a/board/Seagate/nas440/Makefile > > >>>> b/board/Seagate/nas440/Makefile > > >>>> new file mode 100644 > > >>>> index 0000000000..2a3ef746d3 > > >>>> --- /dev/null > > >>>> +++ b/board/Seagate/nas440/Makefile > > >>>> @@ -0,0 +1,7 @@ > > >>>> +# > > >>>> +# Copyright (C) 2014 Evgeni Dobrev <evg...@studio-punkt.com> > > >>>> +# > > >>>> +# SPDX-License-Identifier: GPL-2.0+ > > >>>> +# > > >>>> + > > >>>> +obj-y := nas440.o > > >>>> diff --git a/board/Seagate/nas440/kwbimage.cfg > > >>>> b/board/Seagate/nas440/kwbimage.cfg > > >>>> new file mode 100644 > > >>>> index 0000000000..e71da11694 > > >>>> --- /dev/null > > >>>> +++ b/board/Seagate/nas440/kwbimage.cfg > > >>>> @@ -0,0 +1,156 @@ > > >>>> +# > > >>>> +# Copyright (C) 2021 Hajo Noerenberg <hajo-ub...@noerenberg.de> > > >>>> +# > > >>>> +# Based on nas220/kwbimage.cfg originally written by > > >>>> +# Evgeni Dobrev <evg...@studio-punkt.com> > > >>>> +# > > >>>> +# Based on sheevaplug/kwbimage.cfg originally written by > > >>>> +# Prafulla Wadaskar <prafu...@marvell.com> > > >>>> +# (C) Copyright 2009 > > >>>> +# Marvell Semiconductor <www.marvell.com> > > >>>> +# > > >>>> +# SPDX-License-Identifier: GPL-2.0+ > > >>>> +# > > >>>> +# Refer doc/README.kwbimage for more details about how-to configure > > >>>> +# and create kirkwood boot image > > >>>> +# > > >>>> + > > >>>> +# Boot Media configurations > > >>>> +BOOT_FROM nand > > >>>> +NAND_ECC_MODE default > > >>>> +NAND_PAGE_SIZE 0x0200 > > >>>> + > > >>>> +# SOC registers configuration using bootrom header extension > > >>>> +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed > > >>>> + > > >>>> +# Configure RGMII-0 interface pad voltage to 1.8V > > >>>> +DATA 0xFFD100E0 0x1B1B1B9B > > >>>> + > > >>>> +DATA 0xFFD20134 0xBBBBBBBB > > >>>> +DATA 0xFFD20138 0x00BBBBBB > > >>>> + > > >>>> +#Dram initalization for SINGLE x16 CL=5 @ 400MHz > > >>>> +DATA 0xFFD01400 0x43000C30 # DDR Configuration register > > >>>> +# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) > > >>>> +# bit23-14: zero > > >>>> +# bit24: 1= enable exit self refresh mode on DDR access > > >>>> +# bit25: 1 required > > >>>> +# bit29-26: zero > > >>>> +# bit31-30: 01 > > >>>> + > > >>>> +DATA 0xFFD01404 0x39543000 # DDR Controller Control Low > > >>>> +# bit 4: 0=addr/cmd in smame cycle > > >>>> +# bit 5: 0=clk is driven during self refresh, we don't care for APX > > >>>> +# bit 6: 0=use recommended falling edge of clk for addr/cmd > > >>>> +# bit14: 0=input buffer always powered up > > >>>> +# bit18: 1=cpu lock transaction enabled > > >>>> +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled > > >>>> bit31=0 > > >>>> +# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, > > >>>> unbuffered DIMM > > >>>> +# bit30-28: 3 required > > >>>> +# bit31: 0=no additional STARTBURST delay > > >>>> + > > >>>> +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value > > >>>> +1) > > >>>> +# bit7-4: TRCD > > >>>> +# bit11- 8: TRP > > >>>> +# bit15-12: TWR > > >>>> +# bit19-16: TWTR > > >>>> +# bit20: TRAS msb > > >>>> +# bit23-21: 0x0 > > >>>> +# bit27-24: TRRD > > >>>> +# bit31-28: TRTP > > >>>> + > > >>>> +DATA 0xFFD0140C 0x00000833 # DDR Timing (High) > > >>>> +# bit6-0: TRFC > > >>>> +# bit8-7: TR2R > > >>>> +# bit10-9: TR2W > > >>>> +# bit12-11: TW2W > > >>>> +# bit31-13: zero required > > >>>> + > > >>>> +DATA 0xFFD01410 0x0000000C # DDR Address Control > > >>>> +# bit1-0: 00, Cs0width=x8 > > >>>> +# bit3-2: 11, Cs0size=1Gb > > >>>> +# bit5-4: 00, Cs1width=nonexistent > > >>>> +# bit7-6: 00, Cs1size =nonexistent > > >>>> +# bit9-8: 00, Cs2width=nonexistent > > >>>> +# bit11-10: 00, Cs2size =nonexistent > > >>>> +# bit13-12: 00, Cs3width=nonexistent > > >>>> +# bit15-14: 00, Cs3size =nonexistent > > >>>> +# bit16: 0, Cs0AddrSel > > >>>> +# bit17: 0, Cs1AddrSel > > >>>> +# bit18: 0, Cs2AddrSel > > >>>> +# bit19: 0, Cs3AddrSel > > >>>> +# bit31-20: 0 required > > >>>> + > > >>>> +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control > > >>>> +# bit0: 0, OpenPage enabled > > >>>> +# bit31-1: 0 required > > >>>> + > > >>>> +DATA 0xFFD01418 0x00000000 # DDR Operation > > >>>> +# bit3-0: 0x0, DDR cmd > > >>>> +# bit31-4: 0 required > > >>>> + > > >>>> +DATA 0xFFD0141C 0x00000C52 # DDR Mode > > >>>> +# bit2-0: 2, BurstLen=2 required > > >>>> +# bit3: 0, BurstType=0 required > > >>>> +# bit6-4: 4, CL=5 > > >>>> +# bit7: 0, TestMode=0 normal > > >>>> +# bit8: 0, DLL reset=0 normal > > >>>> +# bit11-9: 6, auto-precharge write recovery ???????????? > > >>>> +# bit12: 0, PD must be zero > > >>>> +# bit31-13: 0 required > > >>>> + > > >>>> +DATA 0xFFD01420 0x00000042 # DDR Extended Mode > > >>>> +# bit0: 0, DDR DLL enabled > > >>>> +# bit1: 0, DDR drive strenght normal > > >>>> +# bit2: 0, DDR ODT control lsd (disabled) > > >>>> +# bit5-3: 000, required > > >>>> +# bit6: 1, DDR ODT control msb, (disabled) > > >>>> +# bit9-7: 000, required > > >>>> +# bit10: 0, differential DQS enabled > > >>>> +# bit11: 0, required > > >>>> +# bit12: 0, DDR output buffer enabled > > >>>> +# bit31-13: 0 required > > >>>> + > > >>>> +DATA 0xFFD01424 0x0000F1FF # DDR Controller Control High > > >>>> +# bit2-0: 111, required > > >>>> +# bit3 : 1 , MBUS Burst Chop disabled > > >>>> +# bit6-4: 111, required > > >>>> +# bit7 : 0 > > >>>> +# bit8 : 0 > > >>>> +# bit9 : 0 , no half clock cycle addition to dataout > > >>>> +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals > > >>>> +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh > > >>>> +# bit15-12: 1111 required > > >>>> +# bit31-16: 0 required > > >>>> + > > >>>> +DATA 0xFFD01428 0x00085520 > > >>>> +DATA 0xFFD0147C 0x00008552 > > >>>> + > > >>>> +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size > > >>>> +# bit0: 1, Window enabled > > >>>> +# bit1: 0, Write Protect disabled > > >>>> +# bit3-2: 00, CS0 hit selected > > >>>> +# bit23-4: ones, required > > >>>> +# bit31-24: 0x07, Size (i.e. 128MB) > > >>>> + > > >>>> +DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 0x0 > > >>>> + > > >>>> +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled > > >>>> + > > >>>> +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled > > >>>> +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled > > >>>> + > > >>>> +DATA 0xFFD01494 0x003C0000 # DDR ODT Control (Low) > > >>>> +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) > > >>>> +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above > > >>>> +# bit3-2: 01, ODT1 active NEVER! > > >>>> +# bit31-4: zero, required > > >>>> + > > >>>> +DATA 0xFFD0149C 0x0000F80F # CPU ODT Control > > >>>> + > > >>>> +DATA 0xFFD01480 0x00000001 # DDR Initialization Control > > >>>> +#bit0=1, enable DDR init upon this register write > > >>>> + > > >>>> +# End of Header extension > > >>>> +DATA 0x0 0x0 > > >>>> + > > >>>> diff --git a/board/Seagate/nas440/nas440.c > > >>>> b/board/Seagate/nas440/nas440.c > > >>>> new file mode 100644 > > >>>> index 0000000000..43a08e61bf > > >>>> --- /dev/null > > >>>> +++ b/board/Seagate/nas440/nas440.c > > >>>> @@ -0,0 +1,378 @@ > > >>>> +/* > > >>>> + * Copyright (C) 2022 Hajo Noerenberg <hajo-ub...@noerenberg.de> > > >>>> + * > > >>>> + * Based on nas220.c originally written by > > >>>> + * Evgeni Dobrev <evg...@studio-punkt.com> > > >>>> + * > > >>>> + * Based on sheevaplug.c originally written by > > >>>> + * Prafulla Wadaskar <prafu...@marvell.com> > > >>>> + * (C) Copyright 2009 > > >>>> + * Marvell Semiconductor <www.marvell.com> > > >>>> + * > > >>>> + * SPDX-License-Identifier: GPL-2.0+ > > >>>> + */ > > >>>> + > > >>>> +#include <common.h> > > >>>> +#include <init.h> > > >>>> +#include <netdev.h> > > >>>> +#include <asm/arch/cpu.h> > > >>>> +#include <asm/arch/soc.h> > > >>>> +#include <asm/arch/mpp.h> > > >>>> +#include <asm/global_data.h> > > >>>> +#include <asm/mach-types.h> > > >>>> +#include <linux/bitops.h> > > >>>> +#include <bootstage.h> > > >>>> +#include <linux/delay.h> > > >>>> +#include <asm/arch/gpio.h> > > >>>> +#include <version.h> > > >>>> + > > >>>> +DECLARE_GLOBAL_DATA_PTR; > > >>>> + > > >>>> +/* > > >>>> + * GPIO pin names, input/output direction and default values > > >>>> + * > > >>>> + * NAS440_GPIO_BUTTON_LCD_LOWER, NAS440_GPIO_BUTTON_LCD_UPPER > > >>>> + * Buttons next to LC display, LOW if pressed > > >>>> + * > > >>>> + * NAS440_GPIO_BUTTON_POWER > > >>>> + * Power button at front of case, LOW if pressed > > >>>> + * > > >>>> + * NAS440_GPIO_BUTTON_RESET > > >>>> + * Reset button at back of case, LOW if pressed > > >>>> + * > > >>>> + * NAS440_GPIO_LCD_HD44780_* > > >>>> + * HD44780-compatible LC display, control via 8bit parallel data > > >>>> transfer > > >>>> + * > > >>>> + * NAS440_GPIO_LED_74AHC164_* > > >>>> + * Control front panel LEDs via 74AHC164 8bit shift register > > >>>> + * > > >>>> + * NAS440_GPIO_SOCSATA_POWER > > >>>> + * 12V Power for SoC SATA ports (NAS drives 3 and 4) > > >>>> + * > > >>>> + * NAS440_GPIO_BOARD_POWER > > >>>> + * Shutdown board if LOW > > >>>> + * > > >>>> + */ > > >>>> + > > >>>> +#define NAS440_GPIO_LCD_HD44780_BACKLIGHT 7 > > >>>> +#define NAS440_GPIO_LED_74AHC164_DATA 12 > > >>>> +#define NAS440_GPIO_LED_74AHC164_CLK 13 > > >>>> +#define NAS440_GPIO_SOCSATA_POWER 28 > > >>>> +#define NAS440_GPIO_BUTTON_RESET 29 > > >>>> +#define NAS440_GPIO_BUTTON_LCD_LOWER 34 > > >>>> +#define NAS440_GPIO_LCD_HD44780_RS 35 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D0 36 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D1 37 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D2 38 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D3 39 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D4 40 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D5 41 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D6 42 > > >>>> +#define NAS440_GPIO_LCD_HD44780_D7 43 > > >>>> +#define NAS440_GPIO_LCD_HD44780_RW 44 > > >>>> +#define NAS440_GPIO_LCD_HD44780_E 45 > > >>>> +#define NAS440_GPIO_BUTTON_LCD_UPPER 47 > > >>>> +#define NAS440_GPIO_BOARD_POWER 48 > > >>>> +#define NAS440_GPIO_BUTTON_POWER 49 > > >>>> + > > >>>> +/* > > >>>> + * GPIO output enable, pins 0-31 to LOW, pins 31-49 to HIGH config > > >>>> register > > >>>> + */ > > >>>> +#define NAS440_GE_OE_LOW > > >>>> (~(BIT(NAS440_GPIO_LCD_HD44780_BACKLIGHT) \ > > >>>> + | BIT(NAS440_GPIO_LED_74AHC164_DATA) > > >>>> \ > > >>>> + | BIT(NAS440_GPIO_LED_74AHC164_CLK) > > >>>> \ > > >>>> + | BIT(NAS440_GPIO_SOCSATA_POWER))) > > >>>> +#define NAS440_GE_OE_HIGH (~(BIT_MASK(NAS440_GPIO_BOARD_POWER) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_RS) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D0) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D1) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D2) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D3) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D4) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D5) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D6) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D7) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_RW) > > >>>> \ > > >>>> + | BIT_MASK(NAS440_GPIO_LCD_HD44780_E))) > > >>>> + > > >>>> +/* > > >>>> + * GPIO output default values > > >>>> + */ > > >>>> +#define NAS440_GE_OE_VAL_LOW BIT(NAS440_GPIO_LCD_HD44780_BACKLIGHT) > > >>>> + > > >>>> +#define NAS440_GE_OE_VAL_HIGH BIT_MASK(NAS440_GPIO_BOARD_POWER) > > >>>> + > > >>>> +int board_early_init_f(void) > > >>>> +{ > > >>>> + /* > > >>>> + * default gpio configuration > > >>>> + */ > > >>>> + mvebu_config_gpio(NAS440_GE_OE_VAL_LOW, NAS440_GE_OE_VAL_HIGH, > > >>>> + NAS440_GE_OE_LOW, NAS440_GE_OE_HIGH); > > >>>> + > > >>>> + /* Multi-Purpose Pins Functionality configuration */ > > >>>> + static const u32 kwmpp_config[] = { > > >>>> + MPP0_NF_IO2, > > >>>> + MPP1_NF_IO3, > > >>>> + MPP2_NF_IO4, > > >>>> + MPP3_NF_IO5, > > >>>> + MPP4_NF_IO6, > > >>>> + MPP5_NF_IO7, > > >>>> + MPP6_SYSRST_OUTn, > > >>>> + MPP7_GPO, /* > > >>>> NAS440_GPIO_LCD_HD44780_BACKLIGHT */ > > >>>> + MPP8_TW_SDA, > > >>>> + MPP9_TW_SCK, > > >>>> + MPP10_UART0_TXD, > > >>>> + MPP11_UART0_RXD, > > >>>> + MPP12_GPO, /* NAS440_GPIO_LED_74AHC164_DATA > > >>>> */ > > >>>> + MPP13_GPIO, /* NAS440_GPIO_LED_74AHC164_CLK > > >>>> */ > > >>>> + MPP14_SATA1_PRESENTn, > > >>>> + MPP15_SATA0_ACTn, > > >>>> + MPP16_SATA1_ACTn, > > >>>> + MPP17_SATA0_PRESENTn, > > >>>> + MPP18_NF_IO0, > > >>>> + MPP19_NF_IO1, > > >>>> + MPP20_GE1_0, /* GbE Port1, RGMII mode (12 > > >>>> pins GE1_0-7, GE1_10-13) */ > > >>>> + MPP21_GE1_1, > > >>>> + MPP22_GE1_2, > > >>>> + MPP23_GE1_3, > > >>>> + MPP24_GE1_4, > > >>>> + MPP25_GE1_5, > > >>>> + MPP26_GE1_6, > > >>>> + MPP27_GE1_7, > > >>>> + MPP28_GPIO, /* NAS440_GPIO_SOCSATA_POWER */ > > >>>> + MPP29_GPIO, /* NAS440_GPIO_BUTTON_RESET */ > > >>>> + MPP30_GE1_10, > > >>>> + MPP31_GE1_11, > > >>>> + MPP32_GE1_12, > > >>>> + MPP33_GE1_13, > > >>>> + MPP34_GPIO, /* NAS440_GPIO_BUTTON_LCD_LOWER > > >>>> */ > > >>>> + MPP35_GPIO, /* NAS440_GPIO_LCD_HD44780_RS */ > > >>>> + MPP36_GPIO, /* NAS440_GPIO_LCD_HD44780_D0 */ > > >>>> + MPP37_GPIO, /* NAS440_GPIO_LCD_HD44780_D1 */ > > >>>> + MPP38_GPIO, /* NAS440_GPIO_LCD_HD44780_D2 */ > > >>>> + MPP39_GPIO, /* NAS440_GPIO_LCD_HD44780_D3 */ > > >>>> + MPP40_GPIO, /* NAS440_GPIO_LCD_HD44780_D4 */ > > >>>> + MPP41_GPIO, /* NAS440_GPIO_LCD_HD44780_D5 */ > > >>>> + MPP42_GPIO, /* NAS440_GPIO_LCD_HD44780_D6 */ > > >>>> + MPP43_GPIO, /* NAS440_GPIO_LCD_HD44780_D7 */ > > >>>> + MPP44_GPIO, /* NAS440_GPIO_LCD_HD44780_RW */ > > >>>> + MPP45_GPIO, /* NAS440_GPIO_LCD_HD44780_E */ > > >>>> + MPP46_GPIO, > > >>>> + MPP47_GPIO, /* NAS440_GPIO_BUTTON_LCD_UPPER > > >>>> */ > > >>>> + MPP48_GPIO, /* NAS440_GPIO_BOARD_POWER */ > > >>>> + MPP49_GPIO, /* NAS440_GPIO_BUTTON_POWER */ > > >>>> + 0 > > >>>> + }; > > >>>> + kirkwood_mpp_conf(kwmpp_config, NULL); > > >>>> + return 0; > > >>>> +} > > >>>> + > > >>>> +/* HD44780 pins, data bits first, backlight last */ > > >>>> +static int hd44780_pins[12] = { > > >>>> + NAS440_GPIO_LCD_HD44780_D0, > > >>>> + NAS440_GPIO_LCD_HD44780_D1, > > >>>> + NAS440_GPIO_LCD_HD44780_D2, > > >>>> + NAS440_GPIO_LCD_HD44780_D3, > > >>>> + NAS440_GPIO_LCD_HD44780_D4, > > >>>> + NAS440_GPIO_LCD_HD44780_D5, > > >>>> + NAS440_GPIO_LCD_HD44780_D6, > > >>>> + NAS440_GPIO_LCD_HD44780_D7, > > >>>> + NAS440_GPIO_LCD_HD44780_E, > > >>>> + NAS440_GPIO_LCD_HD44780_RW, > > >>>> + NAS440_GPIO_LCD_HD44780_RS, > > >>>> + NAS440_GPIO_LCD_HD44780_BACKLIGHT > > >>>> +}; > > >>>> + > > >>>> +#define HD44780_NUM_COL 16 > > >>>> +#define HD44780_BUF_COL 40 > > >>>> +#define HD44780_NUM_ROW 2 > > >>>> + > > >>>> +#define HD44780_PIN_NUM > > >>>> (sizeof(hd44780_pins)/sizeof(int)) > > >>>> + > > >>>> +/* > > >>>> + * HD44780 LCD display commands - adapted from hd44780.h by Joerg > > >>>> Wunsch > > >>>> + * > > >>>> + * > > >>>> ---------------------------------------------------------------------------- > > >>>> + * "THE BEER-WARE LICENSE" (Revision 42): > > >>>> + * <jo...@freebsd.org> wrote this file. As long as you retain this > > >>>> notice you > > >>>> + * can do whatever you want with this stuff. If we meet some day, and > > >>>> you think > > >>>> + * this stuff is worth it, you can buy me a beer in return. > > >>>> Joerg Wunsch > > >>>> + * > > >>>> ---------------------------------------------------------------------------- > > >>>> + */ > > >>>> + > > >>>> +#define HD44780_CMD_CLR \ > > >>>> + 0x01 > > >>>> +#define HD44780_CMD_HOME \ > > >>>> + 0x02 > > >>>> +#define HD44780_CMD_ENTMODE(inc, shift) \ > > >>>> + (0x04 | ((inc)? 0x02: 0) | ((shift)? 1: 0)) > > >>>> +#define HD44780_CMD_DISPCTL(disp, cursor, blink) \ > > >>>> + (0x08 | ((disp)? 0x04: 0) | ((cursor)? 0x02: 0) | ((blink)? 1: > > >>>> 0)) > > >>>> +#define HD44780_CMD_SHIFT(shift, right) \ > > >>>> + (0x10 | ((shift)? 0x08: 0) | ((right)? 0x04: 0)) > > >>>> +#define HD44780_CMD_FNSET(if8bit, twoline, font5x10) \ > > >>>> + (0x20 | ((if8bit)? 0x10: 0) | ((twoline)? 0x08: 0) | \ > > >>>> + ((font5x10)? 0x04: 0)) > > >>>> +#define HD44780_CMD_CGADDR(addr) \ > > >>>> + (0x40 | ((addr) & 0x3f)) > > >>>> +#define HD44780_CMD_DDADDR(addr) \ > > >>>> + (0x80 | ((addr) & 0x7f)) > > >>>> + > > >>>> +static void lcd_send(unsigned int val, int mode) > > >>>> +{ > > >>>> + udelay(1); > > >>>> + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_RS, mode); > > >>>> + udelay(1); > > >>>> + > > >>>> + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_E, 0); > > >>>> + for (int i=0; i<8; i++) { > > >>>> + kw_gpio_set_value(hd44780_pins[i], (val&(1<<i))>>i ); > > >>>> + } > > >>>> + udelay(1); > > >>>> + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_E, 1); > > >>>> + udelay(1); > > >>>> + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_E, 0); > > >>>> + udelay(50); > > >>>> +} > > >>>> + > > >>>> +void lcd_init(void) > > >>>> +{ > > >>>> + for (int i=0; i<HD44780_PIN_NUM; i++) { > > >>>> + kw_gpio_set_valid(hd44780_pins[i], GPIO_OUTPUT_OK); > > >>>> + kw_gpio_direction_output(hd44780_pins[i], i == > > >>>> (HD44780_PIN_NUM-1)); > > >>>> + } > > >>>> + > > >>>> + lcd_send(HD44780_CMD_FNSET(1, 1, 0), 0); > > >>>> + udelay(50); > > >>>> + lcd_send(HD44780_CMD_FNSET(1, 1, 0), 0); > > >>>> + udelay(50); > > >>>> + lcd_send(HD44780_CMD_FNSET(1, 1, 0), 0); > > >>>> + udelay(50); > > >>>> + lcd_send(HD44780_CMD_DISPCTL(1, 0, 0), 0); > > >>>> + udelay(50); > > >>>> + lcd_send(HD44780_CMD_CLR, 0); > > >>>> + udelay(50); > > >>>> + lcd_send(HD44780_CMD_ENTMODE(1, 0), 0); > > >>>> + > > >>>> + udelay(2000); > > >>>> +} > > >>>> + > > >>>> +void lcd_row(int row, char *buf) > > >>>> +{ > > >>>> + int p = 0; > > >>>> + > > >>>> + if (row >= HD44780_NUM_ROW) { > > >>>> + return; > > >>>> + } > > >>>> + > > >>>> + lcd_send(HD44780_CMD_DDADDR(HD44780_BUF_COL * row + 0), 0); > > >>>> + for (int i=0; i<HD44780_NUM_COL; i++) { > > >>>> + if (buf[i] == 0) { > > >>>> + p++; > > >>>> + } > > >>>> + lcd_send(p ? 32 : buf[i], 1); > > >>>> + } > > >>>> +} > > >>>> + > > >>>> +enum led_disk { > > >>>> + LED_DSK_OFF, > > >>>> + LED_DSK_RED > > >>>> + /* LED_DSK_GREEN disk activity led is controlled directly by the > > >>>> hardware */ > > >>>> +}; > > >>>> + > > >>>> +enum led_system { > > >>>> + LED_SYS_OFF, > > >>>> + LED_SYS_BLUE, > > >>>> + LED_SYS_RED > > >>>> +}; > > >>>> + > > >>>> +void led_init(void) > > >>>> +{ > > >>>> + kw_gpio_set_valid(NAS440_GPIO_LED_74AHC164_DATA, GPIO_OUTPUT_OK); > > >>>> + kw_gpio_direction_output(NAS440_GPIO_LED_74AHC164_DATA, 0); > > >>>> + kw_gpio_set_valid(NAS440_GPIO_LED_74AHC164_CLK, GPIO_OUTPUT_OK); > > >>>> + kw_gpio_direction_output(NAS440_GPIO_LED_74AHC164_CLK, 0); > > >>>> +} > > >>>> + > > >>>> +void led_set(enum led_disk disk1, enum led_disk disk2, enum led_disk > > >>>> disk3, > > >>>> + enum led_disk disk4, enum led_system front1 ) > > >>>> +{ > > >>>> + int ledbits = (0x81 | ((front1==LED_SYS_RED)? 0x08 : 0) | > > >>>> ((front1==LED_SYS_BLUE)? 0x04 : 0) \ > > >>>> + | ((disk1==LED_DSK_RED)? 0 : 0x02) | > > >>>> ((disk2==LED_DSK_RED)? 0 : 0x40) \ > > >>>> + | ((disk3==LED_DSK_RED)? 0 : 0x20) | > > >>>> ((disk4==LED_DSK_RED)? 0 : 0x10)); > > >>>> + > > >>>> + for (int i=0; i<8; i++) { > > >>>> + kw_gpio_set_value(NAS440_GPIO_LED_74AHC164_DATA, > > >>>> (ledbits >> i) & 1); > > >>>> + udelay(1); > > >>>> + kw_gpio_set_value(NAS440_GPIO_LED_74AHC164_CLK, 1); > > >>>> + kw_gpio_set_value(NAS440_GPIO_LED_74AHC164_CLK, 0); > > >>>> + } > > >>>> +} > > >>>> + > > >>>> +/* factory firmware delays hard disk spinup, presumably to avoid > > >>>> power peaks */ > > >>>> +void delay_hdd_spinup(void) > > >>>> +{ > > >>>> + lcd_row(1, "Delay HDD spinup"); > > >>>> + > > >>>> + for (int i = 0; i<2500; i++) { > > >>>> + udelay(1000); > > >>>> + } > > >>>> + > > >>>> + kw_gpio_set_valid(NAS440_GPIO_SOCSATA_POWER, GPIO_OUTPUT_OK); > > >>>> + kw_gpio_direction_output(NAS440_GPIO_SOCSATA_POWER, 1); > > >>>> +} > > >>>> + > > >>>> +#if CONFIG_IS_ENABLED(BOOTSTAGE) > > >>>> +void show_boot_progress(int val) > > >>>> +{ > > >>>> + switch (val) { > > >>>> +/* 0123456789abcdef */ > > >>>> + case BOOTSTAGE_ID_BOARD_INIT_DONE: > > >>>> + lcd_row(1, "Board init done"); > > >>>> + break; > > >>>> + case BOOTSTAGE_ID_USB_START: > > >>>> + lcd_row(1, "Init USB"); > > >>>> + break; > > >>>> + case BOOTSTAGE_ID_ETH_START: > > >>>> + lcd_row(1, "Init ethernet"); > > >>>> + break; > > >>>> + case BOOTSTAGE_ID_MAIN_LOOP: > > >>>> + lcd_row(1, "Wait for input"); > > >>>> + break; > > >>>> + case BOOTSTAGE_ID_RUN_OS: > > >>>> + lcd_row(1, "Starting Linux"); > > >>>> + break; > > >>>> + default: > > >>>> + if (val < 0) /* error */ > > >>>> + lcd_row(1, "Error"); > > >>>> + break; > > >>>> + } > > >>>> +} > > >>>> +#endif > > >>>> + > > >>>> +int board_eth_init(struct bd_info *bis) > > >>>> +{ > > >>>> + return cpu_eth_init(bis); > > >>>> +} > > >>>> + > > >>>> +int board_init(void) > > >>>> +{ > > >>>> + /* > > >>>> + * arch number of board > > >>>> + */ > > >>>> + gd->bd->bi_arch_number = MACH_TYPE_DB88F6281_BP; > > >>>> + > > >>>> + /* adress of boot parameters */ > > >>>> + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; > > >>>> + > > >>>> + led_init(); > > >>>> + led_set(LED_DSK_OFF, LED_DSK_OFF, LED_DSK_OFF, LED_DSK_OFF, > > >>>> LED_SYS_BLUE); > > >>>> + > > >>>> + lcd_init(); > > >>>> + lcd_row(0, U_BOOT_VERSION ""); > > >>>> + > > >>>> + delay_hdd_spinup(); > > >>>> + > > >>>> + return 0; > > >>>> +} > > >>>> diff --git a/configs/nas440_defconfig b/configs/nas440_defconfig > > >>>> new file mode 100644 > > >>>> index 0000000000..74faf1a24b > > >>>> --- /dev/null > > >>>> +++ b/configs/nas440_defconfig > > >>>> @@ -0,0 +1,89 @@ > > >>>> +CONFIG_ARM=y > > >>>> +CONFIG_SKIP_LOWLEVEL_INIT=y > > >>>> +CONFIG_SYS_DCACHE_OFF=y > > >>>> +CONFIG_ARCH_CPU_INIT=y > > >>>> +CONFIG_ARCH_KIRKWOOD=y > > >>>> +CONFIG_SUPPORT_PASSING_ATAGS=y > > >>>> +CONFIG_CMDLINE_TAG=y > > >>>> +CONFIG_INITRD_TAG=y > > >>>> +CONFIG_SYS_KWD_CONFIG="board/Seagate/nas440/kwbimage.cfg" > > >>>> +CONFIG_SYS_TEXT_BASE=0x600000 > > >>>> +CONFIG_NR_DRAM_BANKS=2 > > >>>> +CONFIG_TARGET_NAS440=y > > >>>> +CONFIG_ENV_SIZE=0x10000 > > >>>> +CONFIG_ENV_OFFSET=0xA0000 > > >>>> +CONFIG_DEFAULT_DEVICE_TREE="kirkwood-blackarmor-nas440" > > >>>> +CONFIG_IDENT_STRING="\nNAS 440" > > >>>> +# CONFIG_SYS_MALLOC_F is not set > > >>>> +CONFIG_SYS_LOAD_ADDR=0x800000 > > >>>> +CONFIG_SHOW_BOOT_PROGRESS=y > > >>>> +CONFIG_BOOTSTAGE=y > > >>>> +CONFIG_BOOTDELAY=3 > > >>>> +CONFIG_USE_PREBOOT=y > > >>>> +CONFIG_PREBOOT="pci enum; " > > >>>> +# CONFIG_DISPLAY_BOARDINFO is not set > > >>>> +CONFIG_HUSH_PARSER=y > > >>>> +CONFIG_SYS_PROMPT="nas440> " > > >>>> +# CONFIG_CMD_FLASH is not set > > >>>> +CONFIG_CMD_SATA=y > > >>>> +CONFIG_CMD_PCI=y > > >>>> +CONFIG_CMD_DM=y > > >>>> +CONFIG_CMD_SCSI=y > > >>>> +CONFIG_CMD_NAND=y > > >>>> +CONFIG_CMD_USB=y > > >>>> +# CONFIG_CMD_SETEXPR is not set > > >>>> +CONFIG_CMD_DHCP=y > > >>>> +CONFIG_CMD_MII=y > > >>>> +CONFIG_CMD_PING=y > > >>>> +CONFIG_CMD_EXT2=y > > >>>> +CONFIG_CMD_EXT4=y > > >>>> +CONFIG_CMD_FAT=y > > >>>> +CONFIG_CMD_JFFS2=y > > >>>> +CONFIG_CMD_MTDPARTS=y > > >>>> +CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xa0000@0x0(uboot),0x010000@0xa0000(env),0x500000@0xc0000(uimage),0x1a40000@0x5c0000(rootfs)" > > >>>> +CONFIG_CMD_UBI=y > > >>>> +CONFIG_ISO_PARTITION=y > > >>>> +CONFIG_EFI_PARTITION=y > > >>>> +# CONFIG_PARTITION_UUIDS is not set > > >>>> +CONFIG_OF_CONTROL=y > > >>>> +CONFIG_ENV_OVERWRITE=y > > >>>> +CONFIG_ENV_IS_IN_NAND=y > > >>>> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y > > >>>> +CONFIG_NETCONSOLE=y > > >>>> +CONFIG_DM=y > > >>>> +CONFIG_SYS_ATA_STRIDE=4 > > >>>> +CONFIG_SYS_ATA_DATA_OFFSET=0x100 > > >>>> +CONFIG_SYS_ATA_REG_OFFSET=0x100 > > >>>> +CONFIG_SYS_ATA_ALT_OFFSET=0x100 > > >>>> +CONFIG_KIRKWOOD_GPIO=y > > >>>> +CONFIG_MVEBU_GPIO=y > > >>>> +CONFIG_GPIO_EXTRA_HEADER=y > > >>>> +CONFIG_DM_GPIO=y > > >>>> +CONFIG_CMD_GPIO=y > > >>>> +CONFIG_GPIO=y > > >>>> +CONFIG_DM_GPIO_LOOKUP_LABEL=y > > >>>> +# CONFIG_MMC is not set > > >>>> +CONFIG_MTD=y > > >>>> +CONFIG_MTD_RAW_NAND=y > > >>>> +CONFIG_PHY_MARVELL=y > > >>>> +CONFIG_DM_ETH=y > > >>>> +CONFIG_MVGBE=y > > >>>> +CONFIG_MII=y > > >>>> +CONFIG_SATA_MV=y > > >>>> +CONFIG_SYS_SATA_MAX_DEVICE=2 > > >>>> +CONFIG_DM_RTC=y > > >>>> +CONFIG_RTC_MV=y > > >>>> +CONFIG_SYS_NS16550=y > > >>>> +CONFIG_USB=y > > >>>> +CONFIG_DM_USB=y > > >>>> +CONFIG_USB_EHCI_HCD=y > > >>>> +CONFIG_USB_STORAGE=y > > >>>> + > > >>>> +CONFIG_PCI=y > > >>>> +CONFIG_DM_PCI_COMPAT=y > > >>>> +CONFIG_PCI_MVEBU=y > > >>>> +CONFIG_AHCI_PCI=y > > >>>> + > > >>>> +CONFIG_SCSI=y > > >>>> +CONFIG_SCSI_AHCI=y > > >>>> +CONFIG_DM_SCSI=y > > >>>> diff --git a/drivers/ata/ahci-pci.c b/drivers/ata/ahci-pci.c > > >>>> index b1d231e0f9..af7e97dc4a 100644 > > >>>> --- a/drivers/ata/ahci-pci.c > > >>>> +++ b/drivers/ata/ahci-pci.c > > >>>> @@ -38,6 +38,7 @@ U_BOOT_DRIVER(ahci_pci) = { > > >>>> static struct pci_device_id ahci_pci_supported[] = { > > >>>> { PCI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, ~0) }, > > >>>> { PCI_DEVICE(0x1b21, 0x0611) }, > > >>>> + { PCI_DEVICE(0x11ab, 0x6121) }, > > >>>> {}, > > >>>> }; > > >>>> > > >>>> diff --git a/include/configs/nas440.h b/include/configs/nas440.h > > >>>> new file mode 100644 > > >>>> index 0000000000..58e6afb2c3 > > >>>> --- /dev/null > > >>>> +++ b/include/configs/nas440.h > > >>>> @@ -0,0 +1,50 @@ > > >>>> +/* > > >>>> + * Copyright (C) 2022 Hajo Noerenberg <hajo-ub...@noerenberg.de> > > >>>> + * > > >>>> + * based on work from: > > >>>> + * (C) Copyright 2009 > > >>>> + * Marvell Semiconductor <www.marvell.com> > > >>>> + * Written-by: Prafulla Wadaskar <prafu...@marvell.com> > > >>>> + * > > >>>> + * SPDX-License-Identifier: GPL-2.0+ > > >>>> + */ > > >>>> + > > >>>> +#ifndef _CONFIG_NAS440_H > > >>>> +#define _CONFIG_NAS440_H > > >>>> + > > >>>> +/* > > >>>> + * mv-common.h should be defined after CMD configs since it used them > > >>>> + * to enable certain macros > > >>>> + */ > > >>>> + > > >>>> +#include "mv-common.h" > > >>>> + > > >>>> +/* > > >>>> + * Default environment variables > > >>>> + */ > > >>>> + > > >>>> +#define CONFIG_EXTRA_ENV_SETTINGS \ > > >>>> + "bootargs=console=ttyS0,115200\0" \ > > >>>> + "mtdids=nand0=orion_nand\0"\ > > >>>> + "mtdparts=" CONFIG_MTDPARTS_DEFAULT \ > > >>>> + "autostart=no\0"\ > > >>>> + "autoload=no\0" > > >>>> + > > >>>> +/* > > >>>> + * Ethernet Driver configuration > > >>>> + */ > > >>>> +#ifdef CONFIG_MVGBE > > >>>> +#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ > > >>>> +#define CONFIG_PHY_BASE_ADR 8 > > >>>> +#ifdef CONFIG_RESET_PHY_R > > >>>> +#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */ > > >>>> +#endif > > >>>> +#endif /* CONFIG_MVGBE */ > > >>>> + > > >>>> +/* > > >>>> + * SATA driver configuration > > >>>> + */ > > >>>> +#define CONFIG_LBA48 > > >>>> +#define CONFIG_SYS_64BIT_LBA > > >>>> + > > >>>> +#endif /* _CONFIG_NAS440_H */ > > >>>> -- > > >>>> 2.20.1 > > >>>>
