On Wed, Jan 11, 2023 at 09:28:42PM +0100, Joost van Zwieten wrote:
>
>
> On Tue, Jan 10, 2023 at 18:29, Tom Rini <tr...@konsulko.com> wrote:
> > On Wed, Jan 11, 2023 at 12:10:42AM +0100, Joost van Zwieten wrote:
> > >
> > >
> > > On Tue, Jan 10, 2023 at 18:08, Tom Rini <tr...@konsulko.com> wrote:
> > > > On Wed, Jan 11, 2023 at 12:01:46AM +0100, Joost van Zwieten wrote:
> > > > >
> > > > >
> > > > > On Tue, Jan 10, 2023 at 13:41, Tom Rini <tr...@konsulko.com>
> > > wrote:
> > > > > > On Tue, Jan 10, 2023 at 09:13:32AM +0100, Joost van Zwieten
> > > wrote:
> > > > > >
> > > > > > > Dear maintainers,
> > > > > > >
> > > > > > > As of commit 4963f63fe61f15329d77472a762b1d8bf754d24b
> > > U-Boot
> > > > > fails
> > > > > > > to start
> > > > > > > a kernel (with `bootz`) on my Odroid U2 unless I force
> > > > > > > `initrd_high`, e.g.
> > > > > > > to `0x50000000`. With commit 4963f63f and `initrd_high`
> > > > > *unset* I
> > > > > > > get the
> > > > > > > following output:
> > > > > > >
> > > > > > > U-Boot 2020.10-rc2-00314-g4963f63fe6 (Jan 09 2023 -
> > > 23:59:31
> > > > > > > +0100)
> > > > > > >
> > > > > > > CPU: Exynos4412 @ 1 GHz
> > > > > > > Model: Odroid based on Exynos4412
> > > > > > > Type: u3
> > > > > > > DRAM: 2 GiB
> > > > > > > LDO20@VDDQ_EMMC_1.8V: set 1800000 uV; enabling
> > > > > > > LDO22@VDDQ_EMMC_2.8V: set 2800000 uV; enabling
> > > > > > > LDO21@TFLASH_2.8V: set 2800000 uV; enabling
> > > > > > > MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
> > > > > > > Loading Environment from MMC... *** Warning - bad CRC,
> > > using
> > > > > > > default
> > > > > > > environment
> > > > > > >
> > > > > > > In: serial
> > > > > > > Out: serial
> > > > > > > Err: serial
> > > > > > > Boot device: MMC(2)
> > > > > > > Net: No ethernet found.
> > > > > > > Hit any key to stop autoboot: 0
> > > > > > > Odroid # env set fk_kvers 5.10.0-20-armmp
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > ${fdt_addr_r}
> > > > > > > /boot/dtbs/${fk_kvers}/exynos4412-odroidu3.dtb
> > > > > > > 53440 bytes read in 50 ms (1 MiB/s)
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > > > ${kernel_addr_r}
> > > > > > > /boot/vmlinuz-${fk_kvers}
> > > > > > > 4973056 bytes read in 182 ms (26.1 MiB/s)
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > > > ${ramdisk_addr_r}
> > > > > > > /boot/initrd.img-${fk_kvers}
> > > > > > > 22231585 bytes read in 777 ms (27.3 MiB/s)
> > > > > > > Odroid # env set bootargs console=ttySAC1,115200n8
> > > > > > > Odroid # bootz ${kernel_addr_r}
> > > > > ${ramdisk_addr_r}:${filesize}
> > > > > > > ${fdt_addr_r}
> > > > > > > Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
> > > > > > > ## Flattened Device Tree blob at 40800000
> > > > > > > Booting using the fdt blob at 0x40800000
> > > > > > > Loading Ramdisk to b9947000, end bae7aa21 ... OK
> > > > > > > Loading Device Tree to b9936000, end b99460bf ... OK
> > > > > > >
> > > > > > > Starting kernel ...
> > > > > > >
> > > > > > > And that's all I ever see. Normally the initrd loads a
> > > module
> > > > > that
> > > > > > > causes an
> > > > > > > LED on the Odroid to blink, and this is not happening
> > > either,
> > > > > so
> > > > > > > I'm pretty
> > > > > > > confident the kernel doesn't start or at least crashes
> > > before
> > > > > > > producing
> > > > > > > output. If I set `initrd_high` to `0x50000000` (or
> > > something
> > > > > in the
> > > > > > > neighborhood) the kernel starts just fine:
> > > > > > >
> > > > > > > U-Boot 2020.10-rc2-00314-g4963f63fe6 (Jan 09 2023 -
> > > 23:59:31
> > > > > > > +0100)
> > > > > > >
> > > > > > > CPU: Exynos4412 @ 1 GHz
> > > > > > > Model: Odroid based on Exynos4412
> > > > > > > Type: u3
> > > > > > > DRAM: 2 GiB
> > > > > > > LDO20@VDDQ_EMMC_1.8V: set 1800000 uV; enabling
> > > > > > > LDO22@VDDQ_EMMC_2.8V: set 2800000 uV; enabling
> > > > > > > LDO21@TFLASH_2.8V: set 2800000 uV; enabling
> > > > > > > MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
> > > > > > > Loading Environment from MMC... *** Warning - bad CRC,
> > > using
> > > > > > > default
> > > > > > > environment
> > > > > > >
> > > > > > > In: serial
> > > > > > > Out: serial
> > > > > > > Err: serial
> > > > > > > Boot device: MMC(2)
> > > > > > > Net: No ethernet found.
> > > > > > > Hit any key to stop autoboot: 0
> > > > > > > Odroid # env set fk_kvers 5.10.0-20-armmp
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > ${fdt_addr_r}
> > > > > > > /boot/dtbs/${fk_kvers}/exynos4412-odroidu3.dtb
> > > > > > > 53440 bytes read in 49 ms (1 MiB/s)
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > > > ${kernel_addr_r}
> > > > > > > /boot/vmlinuz-${fk_kvers}
> > > > > > > 4973056 bytes read in 181 ms (26.2 MiB/s)
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > > > ${ramdisk_addr_r}
> > > > > > > /boot/initrd.img-${fk_kvers}
> > > > > > > 22231585 bytes read in 777 ms (27.3 MiB/s)
> > > > > > > Odroid # env set bootargs console=ttySAC1,115200n8
> > > > > > > Odroid # env set initrd_high 0x50000000
> > > > > > > Odroid # bootz ${kernel_addr_r}
> > > > > ${ramdisk_addr_r}:${filesize}
> > > > > > > ${fdt_addr_r}
> > > > > > > Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
> > > > > > > ## Flattened Device Tree blob at 40800000
> > > > > > > Booting using the fdt blob at 0x40800000
> > > > > > > Loading Ramdisk to 4eacc000, end 4ffffa21 ... OK
> > > > > > > Loading Device Tree to bae6a000, end bae7a0bf ... OK
> > > > > > >
> > > > > > > Starting kernel ...
> > > > > > >
> > > > > > > [ 0.000000] Booting Linux on physical CPU 0xa00
> > > > > > > <truncated>
> > > > > > >
> > > > > > > The difference between those two runs is the location
> > > where
> > > > > U-Boot
> > > > > > > loads the
> > > > > > > initrd. The parent commit of 4963f63f boots fine without
> > > > > setting
> > > > > > > `initrd_high`:
> > > > > > >
> > > > > > > U-Boot 2020.10-rc2-00313-gdfaf6a5797 (Jan 10 2023 -
> > > 00:13:19
> > > > > > > +0100)
> > > > > > >
> > > > > > > CPU: Exynos4412 @ 1 GHz
> > > > > > > Model: Odroid based on Exynos4412
> > > > > > > Type: u3
> > > > > > > DRAM: 2 GiB
> > > > > > > LDO20@VDDQ_EMMC_1.8V: set 1800000 uV; enabling
> > > > > > > LDO22@VDDQ_EMMC_2.8V: set 2800000 uV; enabling
> > > > > > > LDO21@TFLASH_2.8V: set 2800000 uV; enabling
> > > > > > > MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
> > > > > > > Loading Environment from MMC... *** Warning - bad CRC,
> > > using
> > > > > > > default
> > > > > > > environment
> > > > > > >
> > > > > > > In: serial
> > > > > > > Out: serial
> > > > > > > Err: serial
> > > > > > > Boot device: MMC(2)
> > > > > > > Net: No ethernet found.
> > > > > > > Hit any key to stop autoboot: 0
> > > > > > > Odroid # env set fk_kvers 5.10.0-20-armmp
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > ${fdt_addr_r}
> > > > > > > /boot/dtbs/${fk_kvers}/exynos4412-odroidu3.dtb
> > > > > > > 53440 bytes read in 49 ms (1 MiB/s)
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > > > ${kernel_addr_r}
> > > > > > > /boot/vmlinuz-${fk_kvers}
> > > > > > > 4973056 bytes read in 181 ms (26.2 MiB/s)
> > > > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
> > > > > ${ramdisk_addr_r}
> > > > > > > /boot/initrd.img-${fk_kvers}
> > > > > > > 22231585 bytes read in 776 ms (27.3 MiB/s)
> > > > > > > Odroid # env set bootargs console=ttySAC1,115200n8
> > > > > > > Odroid # bootz ${kernel_addr_r}
> > > > > ${ramdisk_addr_r}:${filesize}
> > > > > > > ${fdt_addr_r}
> > > > > > > Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
> > > > > > > ## Flattened Device Tree blob at 40800000
> > > > > > > Booting using the fdt blob at 0x40800000
> > > > > > > Loading Ramdisk to 4eacc000, end 4ffffa21 ... OK
> > > > > > > Loading Device Tree to 4eabb000, end 4eacb0bf ... OK
> > > > > > >
> > > > > > > Starting kernel ...
> > > > > > >
> > > > > > > [ 0.000000] Booting Linux on physical CPU 0xa00
> > > > > > > <truncated>
> > > > > > >
> > > > > > > I've tested two different kernels from Debian (buster and
> > > > > bullseye)
> > > > > > > and both
> > > > > > > have the same problem. I'm building U-Boot using the
> > > default
> > > > > config
> > > > > > > for
> > > > > > > board `odroid` and boot the Odroid from an SD card with
> > > > > firmware
> > > > > > > (`bl1`,
> > > > > > > `bl2` and `tzsw`) from Hardkernel's clone of the u-boot
> > > > > repository
> > > > > > > [1].
> > > > > > > There are no peripherals connected apart from the SD card
> > > and
> > > > > the
> > > > > > > serial
> > > > > > > console. Please let me know if you need more information.
> > > > > >
> > > > > > Interesting. So what does "bdi" show, both in the older good
> > > and
> > > > > > then current tree? Specifically the information about where
> > > DRAM
> > > > > is, and
> > > > > > how large it is? Thanks.
> > > > > >
> > > > > > --
> > > > > > Tom
> > > > >
> > > > > Both 4963f63f (not working) and its parent (working) produce
> > > the
> > > > > same
> > > > > output:
> > > > >
> > > > > boot_params = 0x40000100
> > > > > DRAM bank = 0x00000000
> > > > > -> start = 0x40000000
> > > > > -> size = 0x10000000
> > > > > DRAM bank = 0x00000001
> > > > > -> start = 0x50000000
> > > > > -> size = 0x10000000
> > > > > DRAM bank = 0x00000002
> > > > > -> start = 0x60000000
> > > > > -> size = 0x10000000
> > > > > DRAM bank = 0x00000003
> > > > > -> start = 0x70000000
> > > > > -> size = 0x10000000
> > > > > DRAM bank = 0x00000004
> > > > > -> start = 0x80000000
> > > > > -> size = 0x10000000
> > > > > DRAM bank = 0x00000005
> > > > > -> start = 0x90000000
> > > > > -> size = 0x10000000
> > > > > DRAM bank = 0x00000006
> > > > > -> start = 0xa0000000
> > > > > -> size = 0x10000000
> > > > > DRAM bank = 0x00000007
> > > > > -> start = 0xb0000000
> > > > > -> size = 0x0ff00000
> > > > > memstart = 0x40000000
> > > > > memsize = 0x7ff00000
> > > > > flashstart = 0x00000000
> > > > > flashsize = 0x00000000
> > > > > flashoffset = 0x00000000
> > > > > baudrate = 115200 bps
> > > > > relocaddr = 0xbfe83000
> > > > > reloc off = 0x7c083000
> > > > > Build = 32-bit
> > > > > current eth = unknown
> > > > > ethaddr = (not set)
> > > > > IP addr = <NULL>
> > > > > fdt_blob = 0xbae7bf00
> > > > > new_fdt = 0xbae7bf00
> > > > > fdt_size = 0x00002fa0
> > > > > lmb_dump_all:
> > > > > memory.cnt = 0x1
> > > > > memory.size = 0x0
> > > > > memory.reg[0x0].base = 0x40000000
> > > > > .size = 0x7ff00000
> > > > >
> > > > > reserved.cnt = 0x1
> > > > > reserved.size = 0x0
> > > > > reserved.reg[0x0].base = 0xbae7acd0
> > > > > .size = 0x5085330
> > > > > arch_number = 0x000010c1
> > > > > TLB addr = 0xbfef0000
> > > > > irq_sp = 0xbae7bef0
> > > > > sp start = 0xbae7bee0
> > > > > Board Type = 0
> > > > > Early malloc usage: f0 / 400
> > > > >
> > > > > I'm not sure if this is relevant, but with the failing commit
> > > I can
> > > > > get the
> > > > > kernel to start with `initrd_high` set to `0x70000000` or
> > > lower,
> > > > > but not
> > > > > higher.
> > > >
> > > > OK, so 8 whole banks, of 256MB each. Does this platform have 2GB
> > > of
> > > > memory for real?
> > > >
> > > > --
> > > > Tom
> > >
> > > Yes, it does. See https://www.hardkernel.com/shop/odroid-u3/ .
> >
> > Thanks. I guess my current thought is that in the absence of adding
> > earlycon to the kernel args, to perhaps get more info out of the kernel
> > as to when / where it's dying, that bootm_size should be set to
> > 0x10000000 (256MB) to replicate the old behavior, on this platform.
> > Jaehoon, do you have any other ideas?
> >
> > --
> > Tom
>
> I was not aware of the existence of `earlycon`. Running the first failing
> commit 4963f63f with `earlycon` and with `initrd_high` *unset* reveals a
> kernel panic:
>
> Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
> ## Flattened Device Tree blob at 40800000
> Booting using the fdt blob at 0x40800000
> Loading Ramdisk to b9947000, end bae7aa21 ... OK
> Loading Device Tree to b9936000, end b99460bf ... OK
>
> Starting kernel ...
>
> [ 0.000000] Booting Linux on physical CPU 0xa00
> [ 0.000000] Linux version 5.10.0-20-armmp
> (debian-ker...@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110,
> GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian 5.10.158-2
> (2022-12-13)
> [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7),
> cr=10c5387d
> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
> instruction cache
> [ 0.000000] OF: fdt: Machine model: Hardkernel ODROID-U3 board based
> on Exynos4412
> [ 0.000000] earlycon: exynos4210 at MMIO 0x13810000 (options '')
> [ 0.000000] printk: bootconsole [exynos4210] enabled
> [ 0.000000] Memory policy: Data cache writealloc
> [ 0.000000] efi: UEFI not found.
> [ 0.000000] Reserved memory: created DMA memory pool at 0xbf700000,
> size 8 MiB
> [ 0.000000] OF: reserved mem: initialized node region_mfc_right,
> compatible id shared-dma-pool
> [ 0.000000] Reserved memory: created DMA memory pool at 0xbd300000,
> size 36 MiB
> [ 0.000000] OF: reserved mem: initialized node region_mfc_left,
> compatible id shared-dma-pool
> [ 0.000000] cma: Reserved 16 MiB at 0xbc000000
> [ 0.000000] Samsung CPU ID: 0xe4412220
> [ 0.000000] Zone ranges:
> [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff]
> [ 0.000000] Normal empty
> [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bd2fffff]So here we go. Initrd cannot be in highmem. I cannot find this documented, quickly, under https://www.kernel.org/doc/html/latest/ so I guess this is more just background knowledge than formal knowledge. This also matches up with your noting that initrd_high=0x70000000 works. -- Tom
signature.asc
Description: PGP signature
