Align the DT with current Linux 6.1 tree, wherever possible.
Signed-off-by: Eugen Hristev <eugen.hris...@microchip.com>
---
arch/arm/dts/at91-sama7g5ek.dts | 23 +++++++++++------------
arch/arm/dts/sama7g5.dtsi | 27 ++++++++++++++++-----------
2 files changed, 27 insertions(+), 23 deletions(-)
diff --git a/arch/arm/dts/at91-sama7g5ek.dts b/arch/arm/dts/at91-sama7g5ek.dts
index aed84f15a1..9b247fcaf6 100644
--- a/arch/arm/dts/at91-sama7g5ek.dts
+++ b/arch/arm/dts/at91-sama7g5ek.dts
@@ -45,13 +45,13 @@
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_key_gpio_default>;
- bp1 {
+ button {
label = "PB_USER";
gpios = <&pioA PIN_PA12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_PROG1>;
@@ -244,8 +244,8 @@
regulators {
vdd_3v3: VDD_IO {
regulator-name = "VDD_IO";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <3700000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-always-on;
@@ -264,8 +264,8 @@
vddioddr: VDD_DDR {
regulator-name = "VDD_DDR";
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1450000>;
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-always-on;
@@ -285,8 +285,8 @@
vddcore: VDD_CORE {
regulator-name = "VDD_CORE";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1850000>;
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-always-on;
@@ -306,7 +306,7 @@
vddcpu: VDD_OTHER {
regulator-name = "VDD_OTHER";
regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1850000>;
+ regulator-max-microvolt = <1250000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-ramp-delay = <3125>;
@@ -326,8 +326,8 @@
vldo1: LDO1 {
regulator-name = "LDO1";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <3700000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-state-standby {
@@ -707,7 +707,6 @@
ck_cd_rstn_vddsel {
pinmux = <PIN_PA0__SDMMC0_CK>,
<PIN_PA2__SDMMC0_RSTN>,
- <PIN_PA14__SDMMC0_CD>,
<PIN_PA11__SDMMC0_DS>;
slew-rate = <0>;
bias-pull-up;
diff --git a/arch/arm/dts/sama7g5.dtsi b/arch/arm/dts/sama7g5.dtsi
index d38090d7dd..6388a60e53 100644
--- a/arch/arm/dts/sama7g5.dtsi
+++ b/arch/arm/dts/sama7g5.dtsi
@@ -15,6 +15,7 @@
#include <dt-bindings/clk/at91.h>
#include <dt-bindings/dma/at91.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
model = "Microchip SAMA7G5 family SoC";
@@ -195,11 +196,11 @@
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
};
pmc: pmc@e0018000 {
@@ -211,6 +212,13 @@
clock-names = "td_slck", "md_slck", "main_xtal",
"main_rc";
};
+ reset_controller: reset-controller@e001d000 {
+ compatible = "microchip,sama7g5-rstc";
+ reg = <0xe001d000 0xc>, <0xe001d0e4 0x4>;
+ #reset-cells = <1>;
+ clocks = <&clk32k 0>;
+ };
+
shdwc: shdwc@e001d010 {
compatible = "microchip,sama7g5-shdwc", "syscon";
reg = <0xe001d010 0x10>;
@@ -229,13 +237,6 @@
clocks = <&clk32k 0>;
};
- reset_controller: rstc@e001d000 {
- compatible = "microchip,sama7g5-rstc",
"microchip,sam9x60-rstc";
- reg = <0xe001d000 0xc>, <0xe001d0e4 0x4>;
- #reset-cells = <1>;
- clocks = <&clk32k 0>;
- };
-
clk32k: clock-controller@e001d050 {
compatible = "microchip,sama7g5-sckc",
"microchip,sam9x60-sckc";
reg = <0xe001d050 0x4>;
@@ -620,6 +621,7 @@
uart0: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
clock-names = "usart";
@@ -668,6 +670,7 @@
uart3: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
clock-names = "usart";
@@ -711,6 +714,7 @@
uart4: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
clock-names = "usart";
@@ -736,6 +740,7 @@
uart7: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
clock-names = "usart";
@@ -884,9 +889,9 @@
#address-cells = <1>;
#size-cells = <0>;
atmel,fifo-size = <32>;
- dmas = <&dma0 AT91_XDMAC_DT_PERID(27)>,
- <&dma0 AT91_XDMAC_DT_PERID(28)>;
- dma-names = "rx", "tx";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(28)>,
+ <&dma0 AT91_XDMAC_DT_PERID(27)>;
+ dma-names = "tx", "rx";
status = "disabled";
};
};
--
2.25.1
