Am Dienstag, dem 03.05.2022 um 20:24 +0800 schrieb Peng Fan (OSS):
> From: Peng Fan <peng....@nxp.com>
>
> pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
> set_wdog_reset function could be handled by imx_watchdog.c driver.
Thank you for the cleanup!
Tested on phyCORE-i.MX8MM and phyCORE-i.MX8MP.
Tested-by: Teresa Remmet <t.rem...@phytec.de>
Regards,
Teresa
>
> Signed-off-by: Peng Fan <peng....@nxp.com>
> ---
> board/phytec/phycore_imx8mm/spl.c | 19 -------------------
> board/phytec/phycore_imx8mp/spl.c | 19 -------------------
> 2 files changed, 38 deletions(-)
>
> diff --git a/board/phytec/phycore_imx8mm/spl.c
> b/board/phytec/phycore_imx8mm/spl.c
> index 7f24a3affc8..d87ab6d4497 100644
> --- a/board/phytec/phycore_imx8mm/spl.c
> +++ b/board/phytec/phycore_imx8mm/spl.c
> @@ -57,23 +57,6 @@ int board_fit_config_name_match(const char *name)
> return 0;
> }
>
> -#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE)
> -
> -static iomux_v3_cfg_t const wdog_pads[] = {
> - IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B |
> MUX_PAD_CTRL(WDOG_PAD_CTRL),
> -};
> -
> -int board_early_init_f(void)
> -{
> - struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
> -
> - imx_iomux_v3_setup_multiple_pads(wdog_pads,
> ARRAY_SIZE(wdog_pads));
> -
> - set_wdog_reset(wdog);
> -
> - return 0;
> -}
> -
> void board_init_f(ulong dummy)
> {
> int ret;
> @@ -82,8 +65,6 @@ void board_init_f(ulong dummy)
>
> init_uart_clk(2);
>
> - board_early_init_f();
> -
> /* Clear the BSS. */
> memset(__bss_start, 0, __bss_end - __bss_start);
>
> diff --git a/board/phytec/phycore_imx8mp/spl.c
> b/board/phytec/phycore_imx8mp/spl.c
> index 38a581bef57..faed6fc3b76 100644
> --- a/board/phytec/phycore_imx8mp/spl.c
> +++ b/board/phytec/phycore_imx8mp/spl.c
> @@ -89,23 +89,6 @@ int board_fit_config_name_match(const char *name)
> return 0;
> }
>
> -#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE |
> PAD_CTL_PE)
> -
> -static iomux_v3_cfg_t const wdog_pads[] = {
> - MX8MP_PAD_GPIO1_IO02__WDOG1_WDOG_B |
> MUX_PAD_CTRL(WDOG_PAD_CTRL),
> -};
> -
> -int board_early_init_f(void)
> -{
> - struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
> -
> - imx_iomux_v3_setup_multiple_pads(wdog_pads,
> ARRAY_SIZE(wdog_pads));
> -
> - set_wdog_reset(wdog);
> -
> - return 0;
> -}
> -
> void board_init_f(ulong dummy)
> {
> int ret;
> @@ -114,8 +97,6 @@ void board_init_f(ulong dummy)
>
> init_uart_clk(0);
>
> - board_early_init_f();
> -
> ret = spl_early_init();
> if (ret) {
> debug("spl_early_init() failed: %d\n", ret);
--
PHYTEC Messtechnik GmbH | Robert-Koch-Str. 39 | 55129 Mainz, Germany
Geschäftsführer: Dipl.-Ing. Michael Mitezki, Dipl.-Ing. Bodo Huber |
Handelsregister Mainz HRB 4656 | Finanzamt Mainz | St.Nr. 266500608, DE
149059855
