Copy the devicetree source for the H2+/H3/H5 SoCs and all existing
boards from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit also adds the following new board devicetree:
- sun8i-h3-nanopi-r1.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <sam...@sholland.org>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun50i-h5-cpu-opp.dtsi | 2 +-
arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts | 9 +-
arch/arm/dts/sun50i-h5.dtsi | 6 +-
.../dts/sun8i-h2-plus-bananapi-m2-zero.dts | 28 ++-
arch/arm/dts/sun8i-h3-beelink-x2.dts | 27 ++-
arch/arm/dts/sun8i-h3-nanopi-neo-air.dts | 28 +++
arch/arm/dts/sun8i-h3-nanopi-r1.dts | 169 ++++++++++++++++++
arch/arm/dts/sun8i-h3-nanopi.dtsi | 1 +
arch/arm/dts/sun8i-h3-orangepi-2.dts | 3 +-
arch/arm/dts/sun8i-h3-orangepi-pc.dts | 3 +-
arch/arm/dts/sun8i-h3.dtsi | 10 +-
arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi | 18 +-
arch/arm/dts/sunxi-bananapi-m2-plus.dtsi | 4 +-
arch/arm/dts/sunxi-h3-h5.dtsi | 42 ++++-
arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi | 13 ++
arch/arm/dts/sunxi-libretech-all-h3-it.dtsi | 2 +-
17 files changed, 342 insertions(+), 24 deletions(-)
create mode 100644 arch/arm/dts/sun8i-h3-nanopi-r1.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 6433f63455..bbd69d3a67 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -655,6 +655,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h3-nanopi-m1-plus.dtb \
sun8i-h3-nanopi-neo.dtb \
sun8i-h3-nanopi-neo-air.dtb \
+ sun8i-h3-nanopi-r1.dtb \
sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-lite.dtb \
sun8i-h3-orangepi-one.dtb \
diff --git a/arch/arm/dts/sun50i-h5-cpu-opp.dtsi
b/arch/arm/dts/sun50i-h5-cpu-opp.dtsi
index b265720195..1afad8b437 100644
--- a/arch/arm/dts/sun50i-h5-cpu-opp.dtsi
+++ b/arch/arm/dts/sun50i-h5-cpu-opp.dtsi
@@ -2,7 +2,7 @@
// Copyright (C) 2020 Chen-Yu Tsai <w...@csie.org>
/ {
- cpu_opp_table: cpu-opp-table {
+ cpu_opp_table: opp-table-cpu {
compatible = "operating-points-v2";
opp-shared;
diff --git a/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts
b/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts
index 55bcdf8d1a..55b369534a 100644
--- a/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts
+++ b/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts
@@ -142,9 +142,16 @@
status = "okay";
eeprom@51 {
- compatible = "microchip,24c02";
+ compatible = "microchip,24c02", "atmel,24c02";
reg = <0x51>;
pagesize = <16>;
+ read-only;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eth_mac1: mac-address@fa {
+ reg = <0xfa 0x06>;
+ };
};
};
diff --git a/arch/arm/dts/sun50i-h5.dtsi b/arch/arm/dts/sun50i-h5.dtsi
index ab860e20d0..9b3462b13c 100644
--- a/arch/arm/dts/sun50i-h5.dtsi
+++ b/arch/arm/dts/sun50i-h5.dtsi
@@ -217,7 +217,7 @@
};
};
- gpu_thermal {
+ gpu-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&ths 1>;
@@ -233,6 +233,10 @@
compatible = "allwinner,sun50i-h5-de2-clk";
};
+&mbus {
+ compatible = "allwinner,sun50i-h5-mbus";
+};
+
&mmc0 {
compatible = "allwinner,sun50i-h5-mmc",
"allwinner,sun50i-a64-mmc";
diff --git a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
index f3f7a2c912..d5c7b7984d 100644
--- a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -26,6 +26,17 @@
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "c";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -41,8 +52,9 @@
sw4 {
label = "power";
- linux,code = <BTN_0>;
+ linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ wakeup-source;
};
};
@@ -103,10 +115,24 @@
cpu-supply = <®_vdd_cpux>;
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
b/arch/arm/dts/sun8i-h3-beelink-x2.dts
index 62b5280ec0..cd9f655e4f 100644
--- a/arch/arm/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -57,6 +57,12 @@
ethernet1 = &sdiowifi;
};
+ cec-gpio {
+ compatible = "cec-gpio";
+ cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /*
PA14 */
+ hdmi-phandle = <&hdmi>;
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
@@ -87,11 +93,15 @@
};
};
- wifi_pwrseq: wifi_pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
- clocks = <&rtc 1>;
- clock-names = "ext_clock";
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "power";
+ linux,code = <KEY_POWER>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
};
sound_spdif {
@@ -111,6 +121,13 @@
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ };
};
&de {
diff --git a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
index be49eabbff..cd3df12b65 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
@@ -103,12 +103,40 @@
};
};
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rtc 1>;
+ clock-names = "lpo";
+ vbat-supply = <®_vcc3v3>;
+ vddio-supply = <®_vcc3v3>;
+ device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+ shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+ };
+};
+
&usbphy {
/* USB VBUS is always on */
status = "okay";
diff --git a/arch/arm/dts/sun8i-h3-nanopi-r1.dts
b/arch/arm/dts/sun8i-h3-nanopi-r1.dts
new file mode 100644
index 0000000000..26e2e6172e
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-nanopi-r1.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Igor Pecovnik <i...@armbian.com>
+ * Copyright (C) 2020 Jayantajit Gogoi <jayanta.gogoi...@gmail.com>
+ * Copyright (C) 2020 Yu-Tung Chang <mtw...@gmail.com>
+*/
+
+#include "sun8i-h3-nanopi.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "FriendlyARM NanoPi R1";
+ compatible = "friendlyarm,nanopi-r1", "allwinner,sun8i-h3";
+
+ aliases {
+ serial1 = &uart1;
+ ethernet0 = &emac;
+ ethernet1 = &wifi;
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+ };
+
+ reg_vdd_cpux: gpio-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>;
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ gpios-states = <0x1>;
+ states = <1100000 0x0>,
+ <1300000 0x1>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ };
+
+ leds {
+ led-2 {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+ };
+
+ led-3 {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; /* PA9 */
+ };
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ wifi: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rtc 1>;
+ clock-names = "lpo";
+ vbat-supply = <®_vcc3v3>;
+ vddio-supply = <®_vcc3v3>;
+ device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+ shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+ };
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "otg";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-nanopi.dtsi
b/arch/arm/dts/sun8i-h3-nanopi.dtsi
index c7c3e7d8b3..fc45d5aaa6 100644
--- a/arch/arm/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/dts/sun8i-h3-nanopi.dtsi
@@ -81,6 +81,7 @@
label = "k1";
linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ wakeup-source;
};
};
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts
b/arch/arm/dts/sun8i-h3-orangepi-2.dts
index 597c425d08..9daffd90c1 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -99,8 +99,9 @@
sw4 {
label = "sw4";
- linux,code = <BTN_0>;
+ linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ wakeup-source;
};
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc.dts
b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
index 5aff8ecc66..90f75fa85e 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
@@ -91,8 +91,9 @@
sw4 {
label = "sw4";
- linux,code = <BTN_0>;
+ linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ wakeup-source;
};
};
};
diff --git a/arch/arm/dts/sun8i-h3.dtsi b/arch/arm/dts/sun8i-h3.dtsi
index 4e89701df9..eac2349a23 100644
--- a/arch/arm/dts/sun8i-h3.dtsi
+++ b/arch/arm/dts/sun8i-h3.dtsi
@@ -44,7 +44,7 @@
#include <dt-bindings/thermal/thermal.h>
/ {
- cpu0_opp_table: opp_table0 {
+ cpu0_opp_table: opp-table-cpu {
compatible = "operating-points-v2";
opp-shared;
@@ -112,7 +112,7 @@
};
};
- gpu_opp_table: gpu-opp-table {
+ gpu_opp_table: opp-table-gpu {
compatible = "operating-points-v2";
opp-120000000 {
@@ -245,7 +245,7 @@
cpu_thermal: cpu-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
- thermal-sensors = <&ths 0>;
+ thermal-sensors = <&ths>;
trips {
cpu_hot_trip: cpu-hot {
@@ -282,6 +282,10 @@
compatible = "allwinner,sun8i-h3-de2-clk";
};
+&mbus {
+ compatible = "allwinner,sun8i-h3-mbus";
+};
+
&mmc0 {
compatible = "allwinner,sun7i-a20-mmc";
clocks = <&ccu CLK_BUS_MMC0>,
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
index 22466afd38..235994a4a2 100644
--- a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
@@ -16,15 +16,27 @@
regulator-type = "voltage";
regulator-boot-on;
regulator-always-on;
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1300000>;
+ regulator-min-microvolt = <1108475>;
+ regulator-max-microvolt = <1308475>;
regulator-ramp-delay = <50>; /* 4ms */
gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
gpios-states = <0x1>;
- states = <1100000 0>, <1300000 1>;
+ states = <1108475 0>, <1308475 1>;
};
};
&cpu0 {
cpu-supply = <®_vdd_cpux>;
};
+
+&cpu1 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&cpu2 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&cpu3 {
+ cpu-supply = <®_vdd_cpux>;
+};
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
index 8e5cb3b3fd..d03f5853ef 100644
--- a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
@@ -82,8 +82,9 @@
sw4 {
label = "power";
- linux,code = <BTN_0>;
+ linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ wakeup-source;
};
};
@@ -219,6 +220,7 @@
bluetooth {
compatible = "brcm,bcm43438-bt";
+ max-speed = <1500000>;
clocks = <&rtc 1>;
clock-names = "lpo";
vbat-supply = <®_vcc3v3>;
diff --git a/arch/arm/dts/sunxi-h3-h5.dtsi b/arch/arm/dts/sunxi-h3-h5.dtsi
index 9be13378d4..6cea57e07f 100644
--- a/arch/arm/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/dts/sunxi-h3-h5.dtsi
@@ -567,9 +567,14 @@
};
mbus: dram-controller@1c62000 {
- compatible = "allwinner,sun8i-h3-mbus";
- reg = <0x01c62000 0x1000>;
- clocks = <&ccu CLK_MBUS>;
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c62000 0x1000>,
+ <0x01c63000 0x1000>;
+ reg-names = "mbus", "dram";
+ clocks = <&ccu CLK_MBUS>,
+ <&ccu CLK_DRAM>,
+ <&ccu CLK_BUS_DRAM>;
+ clock-names = "mbus", "dram", "bus";
#address-cells = <1>;
#size-cells = <1>;
dma-ranges = <0x00000000 0x40000000 0xc0000000>;
@@ -812,8 +817,8 @@
reg-io-width = <1>;
interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
- <&ccu CLK_HDMI>;
- clock-names = "iahb", "isfr", "tmds";
+ <&ccu CLK_HDMI>, <&rtc 0>;
+ clock-names = "iahb", "isfr", "tmds", "cec";
resets = <&ccu RST_BUS_HDMI1>;
reset-names = "ctrl";
phys = <&hdmi_phy>;
@@ -859,6 +864,15 @@
#clock-cells = <1>;
};
+ r_intc: interrupt-controller@1f00c00 {
+ compatible = "allwinner,sun8i-h3-r-intc",
+ "allwinner,sun6i-a31-r-intc";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x01f00c00 0x400>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
r_ccu: clock@1f01400 {
compatible = "allwinner,sun8i-h3-r-ccu";
reg = <0x01f01400 0x100>;
@@ -897,6 +911,19 @@
#size-cells = <0>;
};
+ r_uart: serial@1f02800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01f02800 0x400>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&r_ccu CLK_APB0_UART>;
+ resets = <&r_ccu RST_APB0_UART>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins>;
+ status = "disabled";
+ };
+
r_pio: pinctrl@1f02c00 {
compatible = "allwinner,sun8i-h3-r-pinctrl";
reg = <0x01f02c00 0x400>;
@@ -922,6 +949,11 @@
pins = "PL10";
function = "s_pwm";
};
+
+ r_uart_pins: r-uart-pins {
+ pins = "PL2", "PL3";
+ function = "s_uart";
+ };
};
r_pwm: pwm@1f03800 {
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
index 19b3b23cfa..9e14fe5fdc 100644
--- a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
+++ b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
@@ -49,6 +49,7 @@
label = "power";
linux,code = <KEY_POWER>;
gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+ wakeup-source;
};
};
@@ -128,6 +129,18 @@
cpu-supply = <®_vdd_cpux>;
};
+&cpu1 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&cpu2 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&cpu3 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
&de {
status = "okay";
};
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
index 204fba3614..50d328c2a8 100644
--- a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
+++ b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
@@ -156,7 +156,7 @@
&spi0 {
status = "okay";
- spiflash@0 {
+ flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
--
2.35.1
