On Tue, Apr 12, 2022 at 6:31 PM Peng Fan (OSS) <peng....@oss.nxp.com> wrote:
>
> From: Peng Fan <peng....@nxp.com>
>
> Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
> marked with u-boot,dm-spl.
>
> Signed-off-by: Peng Fan <peng....@nxp.com>
> ---
> board/freescale/imx8mn_evk/spl.c | 12 ++----------
> configs/imx8mn_ddr4_evk_defconfig | 1 +
> configs/imx8mn_evk_defconfig | 1 +
> 3 files changed, 4 insertions(+), 10 deletions(-)
>
> diff --git a/board/freescale/imx8mn_evk/spl.c
> b/board/freescale/imx8mn_evk/spl.c
> index 03f2a56e805..8708c93fa34 100644
> --- a/board/freescale/imx8mn_evk/spl.c
> +++ b/board/freescale/imx8mn_evk/spl.c
> @@ -110,14 +110,8 @@ int board_fit_config_name_match(const char *name)
> }
> #endif
>
> -#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
> #define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE |
> PAD_CTL_PE)
>
> -static iomux_v3_cfg_t const uart_pads[] = {
> - IMX8MN_PAD_UART2_RXD__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
> - IMX8MN_PAD_UART2_TXD__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
> -};
> -
> static iomux_v3_cfg_t const wdog_pads[] = {
> IMX8MN_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
> };
> @@ -130,8 +124,6 @@ int board_early_init_f(void)
>
> set_wdog_reset(wdog);
>
> - imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
> -
> return 0;
> }
>
> @@ -147,8 +139,6 @@ void board_init_f(ulong dummy)
>
> timer_init();
>
> - preloader_console_init();
> -
> /* Clear the BSS. */
> memset(__bss_start, 0, __bss_end - __bss_start);
>
> @@ -158,6 +148,8 @@ void board_init_f(ulong dummy)
> hang();
> }
>
> + preloader_console_init();
> +
> enable_tzc380();
>
> /* DDR initialization */
> diff --git a/configs/imx8mn_ddr4_evk_defconfig
> b/configs/imx8mn_ddr4_evk_defconfig
> index 917cdb5aa9d..474d9cfa4d2 100644
> --- a/configs/imx8mn_ddr4_evk_defconfig
> +++ b/configs/imx8mn_ddr4_evk_defconfig
> @@ -76,6 +76,7 @@ CONFIG_PINCTRL_IMX8M=y
> CONFIG_DM_REGULATOR=y
> CONFIG_DM_REGULATOR_FIXED=y
> CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_DM_SERIAL=y
> CONFIG_MXC_UART=y
> CONFIG_SYSRESET=y
> CONFIG_SPL_SYSRESET=y
> diff --git a/configs/imx8mn_evk_defconfig b/configs/imx8mn_evk_defconfig
> index 7749ebe537e..5bc175154ba 100644
> --- a/configs/imx8mn_evk_defconfig
> +++ b/configs/imx8mn_evk_defconfig
> @@ -83,6 +83,7 @@ CONFIG_DM_REGULATOR=y
> CONFIG_SPL_DM_REGULATOR=y
> CONFIG_DM_REGULATOR_FIXED=y
> CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_DM_SERIAL=y
> CONFIG_MXC_UART=y
> CONFIG_SYSRESET=y
> CONFIG_SPL_SYSRESET=y
> --
> 2.35.1
>
Peng,
I see you've been able to get SPL DM_SERIAL to work on IMX8M. This
patch won't apply by the way due to commit ff1c7961d813 ("ARM: imx:
imx8mn-evk: enable DM_SERIAL") so I think you need to rebase.
I have not been able to get SPL DM_SERIAL to work on IMX8MM/IMX8MN...
it hangs my board. Is this due to moving preloader_console_init()
perhaps? Moving it didn't work for me.
Please explain the move of preloader_console_init() and please let me
know if you have tested this on imx/master. Fabio, perhaps you can
test?
Best Regards,
Tim
