[PATCH v2] ARM: imx: imx8mn-*-evk: use DM settings for PHY configuration

[Heiko Thiery]

With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.

Suggested-by: Michael Walle <mich...@walle.cc>
Signed-off-by: Heiko Thiery <heiko.thi...@gmail.com>
---
v2:
 - remove phy-reset-gpios node (thanks to Michael)
    When using DM_ETH_PHY the reset-gpios from the phy is used

 arch/arm/dts/imx8mn-evk.dtsi            | 10 +++++++++-
 board/freescale/imx8mn_evk/imx8mn_evk.c | 16 ----------------
 2 files changed, 9 insertions(+), 17 deletions(-)

diff --git a/arch/arm/dts/imx8mn-evk.dtsi b/arch/arm/dts/imx8mn-evk.dtsi
index 416fadb22b..fd253f0042 100644
--- a/arch/arm/dts/imx8mn-evk.dtsi
+++ b/arch/arm/dts/imx8mn-evk.dtsi
@@ -53,7 +53,6 @@
        pinctrl-0 = <&pinctrl_fec1>;
        phy-mode = "rgmii-id";
        phy-handle = <&ethphy0>;
-       phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
        fsl,magic-packet;
        status = "okay";
 
@@ -64,6 +63,15 @@
                ethphy0: ethernet-phy@0 {
                        compatible = "ethernet-phy-ieee802.3-c22";
                        reg = <0>;
+                       reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+                       reset-assert-us = <10000>;
+                       qca,disable-smarteee;
+                       vddio-supply = <&vddio>;
+
+                       vddio: vddio-regulator {
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <1800000>;
+                       };
                };
        };
 };
diff --git a/board/freescale/imx8mn_evk/imx8mn_evk.c 
b/board/freescale/imx8mn_evk/imx8mn_evk.c
index b24342fd5c..e35d505aea 100644
--- a/board/freescale/imx8mn_evk/imx8mn_evk.c
+++ b/board/freescale/imx8mn_evk/imx8mn_evk.c
@@ -27,22 +27,6 @@ static void setup_fec(void)
        clrsetbits_le32(&gpr->gpr[1], 0x2000, 0);
 }
 
-int board_phy_config(struct phy_device *phydev)
-{
-       /* enable rgmii rxc skew and phy mode select to RGMII copper */
-       phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
-       phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
-
-       phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
-       phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
-       phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
-       phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
-
-       if (phydev->drv->config)
-               phydev->drv->config(phydev);
-       return 0;
-}
-
 int board_init(void)
 {
        setup_fec();
-- 
2.30.2