Hi,
On 11/30/21 00:01, Daniel Cizinsky wrote:
On Tue, Nov 09, 2021 at 09:21:41PM +0100, Daniel Cizinsky wrote:
Hi!
I am trying to switch to as much current vanilla SW as possible on Xilinx
ZCU102 evaluation board. But I am stuck at a very early stage.
I've got U-Boot + SPL + Linux kernel & userspace compilled, but even after
trying hard I had no success in running SPL to read ATF, not even speaking
about the main U-Boot.
I don't even know whether my e-mail went through to the conference. I just
wanted to know, if not being able to use SD card on this board using a
vanilla modern U-Boot SPL is a known bug, or if there are any people
outthere using it successfully. Probably not, or they are not interested in
sharing the simple fact.
With rc3 I'm getting exactly the same errors:
U-Boot SPL 2022.01-rc3 (Nov 29 2021 - 23:50:47 +0100)
PMUFW: v1.1
Loading new PMUFW cfg obj (2024 bytes)
Silicon version: 3
EL Level: EL3
Multiboot: 0
Trying to boot from MMC2
spl: could not initialize mmc. error: -19
Trying to boot from MMC1
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-legacy =
0 0
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-mmc-hs =
63 72
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-sd-hs =
63 60
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-uhs-sdr12
= 0 0
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-uhs-sdr25
= 63 60
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-uhs-sdr50
= 0 72
arasan_sdhci mmc@ff170000: Using predefined clock phase for
clk-phase-uhs-sdr104 = 0 135
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-uhs-ddr50
= 183 48
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-mmc-ddr52
= 54 72
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-mmc-hs200
= 0 135
arasan_sdhci mmc@ff170000: Using predefined clock phase for clk-phase-mmc-hs400
= 0 0
arasan_sdhci mmc@ff170000: arasan_sdhci_set_tapdelay, host:mmc@ff170000, mode:0
CMD_SEND:0
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:8
ARG 0x000001aa
RET -110
CMD_SEND:55
ARG 0x00000000
RET -110
CMD_SEND:0
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:1
ARG 0x00000000
RET -110
Card did not respond to voltage select! : -110
mmc_init: -95, time 23
spl: mmc init failed with error: -95
SPL: Unsupported Boot Device 0
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
I did try latest yesterday and didn't see any issue. How do you build
u-boot? And what board version do you have?
Log below.
Thanks,
Michal
U-Boot SPL 2022.01-rc2-00097-g657a869c04e9 (Nov 29 2021 - 14:15:08 +0100)
PMUFW: v1.1
Loading new PMUFW cfg obj (2032 bytes)
Silicon version: 3
EL Level: EL3
Chip ID: zu9eg
Multiboot: 0
Trying to boot from MMC2
spl: could not initialize mmc. error: -19
Trying to boot from MMC1
spl_load_image_fat_os: error reading image u-boot.bin, err - -2
NOTICE: BL31: Secure code at 0x7e000000
NOTICE: BL31: Non secure code at 0x8000000
NOTICE: BL31: v2.4(release):v2.4-594-g82a773bd39b4
NOTICE: BL31: Built : 07:54:47, Oct 20 2021
U-Boot 2022.01-rc2-00097-g657a869c04e9 (Nov 29 2021 - 14:15:08 +0100)
CPU: ZynqMP
Silicon: v3
Model: ZynqMP ZCU102 Rev1.0
Board: Xilinx ZynqMP
DRAM: 4 GiB
PMUFW: v1.1
Xilinx I2C Legacy format at nvmem0:
Board name: zcu102
Board rev: 1.0
Board SN: 847316301727-67998
Ethernet mac: 00:0a:35:03:70:f6
EL Level: EL2
Chip ID: zu9eg
NAND: 0 MiB
MMC: mmc@ff170000: 0
Loading Environment from FAT... *** Error - No Valid Environment Area found
*** Warning - bad env area, using default environment
In: serial
Out: serial
Err: serial
Bootmode: LVL_SHFT_SD_MODE1
Reset reason: SRST
Net:
ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id
eth0: ethernet@ff0e0000
scanning bus for devices...
SATA link 0 timeout.
SATA link 1 timeout.
AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst
starting USB...
Bus dwc3@fe200000: Register 2000440 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus dwc3@fe200000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
ZynqMP>
