Enable OP-TEE resources and SMCI over OP-TEE on STM32MP15xx-EV1/DK2
boards.
Signed-off-by: Etienne Carriere <etienne.carri...@linaro.org>
---
arch/arm/dts/stm32mp15-u-boot.dtsi | 81 +++++------
arch/arm/dts/stm32mp151.dtsi | 145 ++++++++++++--------
arch/arm/dts/stm32mp153.dtsi | 6 +-
arch/arm/dts/stm32mp157.dtsi | 2 +-
arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 114 +--------------
arch/arm/dts/stm32mp157c-dk2-u-boot.dtsi | 40 ++++++
arch/arm/dts/stm32mp157c-dk2.dts | 9 ++
arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi | 99 +------------
arch/arm/dts/stm32mp157c-ed1.dts | 5 +
arch/arm/dts/stm32mp157c-odyssey.dts | 14 ++
arch/arm/dts/stm32mp15xc.dtsi | 4 +-
include/dt-bindings/clock/stm32mp1-clks.h | 27 ++++
include/dt-bindings/reset/stm32mp1-resets.h | 14 ++
13 files changed, 248 insertions(+), 312 deletions(-)
diff --git a/arch/arm/dts/stm32mp15-u-boot.dtsi
b/arch/arm/dts/stm32mp15-u-boot.dtsi
index 43a7909978..6fd204c635 100644
--- a/arch/arm/dts/stm32mp15-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp15-u-boot.dtsi
@@ -21,23 +21,11 @@
pinctrl1 = &pinctrl_z;
};
- clocks {
- u-boot,dm-pre-reloc;
- };
-
/* need PSCI for sysreset during board_f */
psci {
u-boot,dm-pre-proper;
};
- reboot {
- u-boot,dm-pre-reloc;
- compatible = "syscon-reboot";
- regmap = <&rcc>;
- offset = <0x404>;
- mask = <0x1>;
- };
-
soc {
u-boot,dm-pre-reloc;
@@ -72,36 +60,6 @@
u-boot,dm-pre-reloc;
};
-&clk_csi {
- u-boot,dm-pre-reloc;
-};
-
-&clk_hsi {
- u-boot,dm-pre-reloc;
-};
-
-&clk_hse {
- u-boot,dm-pre-reloc;
-};
-
-&clk_lsi {
- u-boot,dm-pre-reloc;
-};
-
-&clk_lse {
- u-boot,dm-pre-reloc;
-};
-
-&cpu0_opp_table {
- u-boot,dm-spl;
- opp-650000000 {
- u-boot,dm-spl;
- };
- opp-800000000 {
- u-boot,dm-spl;
- };
-};
-
&gpioa {
u-boot,dm-pre-reloc;
};
@@ -161,8 +119,8 @@
/* temp = waiting kernel update */
&m4_rproc {
- resets = <&rcc MCU_R>,
- <&rcc MCU_HOLD_BOOT_R>;
+ resets = <&scmi0_reset RST_SCMI0_MCU>,
+ <&scmi0_reset RST_SCMI0_MCU_HOLD_BOOT>;
reset-names = "mcu_rst", "hold_boot";
};
@@ -174,6 +132,7 @@
u-boot,dm-pre-reloc;
};
+// TODO: remove once PWR under SCMI
&pwr_regulators {
u-boot,dm-pre-reloc;
};
@@ -184,6 +143,38 @@
#size-cells = <0>;
};
+&scmi0 {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi0_clk {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi0_reset {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi0_shm {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi1 {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi1_clk {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi1_shm {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi_sram {
+ u-boot,dm-pre-reloc;
+};
+
&sdmmc1 {
compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
};
@@ -197,7 +188,7 @@
};
&usart1 {
- resets = <&rcc USART1_R>;
+ resets = <&scmi0_reset RST_SCMI0_USART1>;
};
&usart2 {
diff --git a/arch/arm/dts/stm32mp151.dtsi b/arch/arm/dts/stm32mp151.dtsi
index 8e0a0bc1dd..db48077375 100644
--- a/arch/arm/dts/stm32mp151.dtsi
+++ b/arch/arm/dts/stm32mp151.dtsi
@@ -48,6 +48,69 @@
interrupt-parent = <&intc>;
};
+ scmi_sram: sram@2ffff000 {
+ compatible = "mmio-sram";
+ reg = <0x2ffff000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x2ffff000 0x1000>;
+
+ scmi0_shm: scmi_shm@0 {
+ reg = <0 0x80>;
+ };
+
+ scmi1_shm: scmi_shm@200 {
+ reg = <0x200 0x80>;
+ };
+ };
+
+ firmware {
+ optee: optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ status = "disabled";
+ };
+
+ scmi0: scmi0 {
+ compatible = "linaro,scmi-optee";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ linaro,optee-channel-id = <0>;
+ /* Supply properties for arm,scmi-smc compatible */
+ arm,smc-id = <0x82002000>;
+ shmem = <&scmi0_shm>;
+ /* Enable only if stm32mp15x RCC[TZEN]=1 */
+ status = "disabled";
+
+ scmi0_clk: protocol@14 {
+ reg = <0x14>;
+ #clock-cells = <1>;
+ };
+
+ scmi0_reset: protocol@16 {
+ reg = <0x16>;
+ #reset-cells = <1>;
+ };
+ };
+
+ scmi1: scmi1 {
+ compatible = "linaro,scmi-optee";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ linaro,optee-channel-id = <1>;
+ /* Supply properties for arm,scmi-smc compatible */
+ arm,smc-id = <0x82002001>;
+ shmem = <&scmi1_shm>;
+ /* Enable only if stm32mp15x RCC[MCKPROT]=1 */
+ status = "disabled";
+
+ scmi1_clk: protocol@14 {
+ reg = <0x14>;
+ #clock-cells = <1>;
+ };
+ };
+ };
+
psci {
compatible = "arm,psci-1.0";
method = "smc";
@@ -70,38 +133,6 @@
interrupt-parent = <&intc>;
};
- clocks {
- clk_hse: clk-hse {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- };
-
- clk_hsi: clk-hsi {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <64000000>;
- };
-
- clk_lse: clk-lse {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- };
-
- clk_lsi: clk-lsi {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32000>;
- };
-
- clk_csi: clk-csi {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <4000000>;
- };
- };
-
thermal-zones {
cpu_thermal: cpu-thermal {
polling-delay-passive = <0>;
@@ -571,7 +602,7 @@
compatible = "st,stm32-cec";
reg = <0x40016000 0x400>;
interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&rcc CEC_K>, <&clk_lse>;
+ clocks = <&rcc CEC_K>, <&scmi0_clk CK_SCMI0_LSE>;
clock-names = "cec", "hdmi-cec";
status = "disabled";
};
@@ -1143,16 +1174,19 @@
};
rcc: rcc@50000000 {
- compatible = "st,stm32mp1-rcc", "syscon";
+ compatible = "st,stm32mp1-rcc-secure",
"st,stm32mp1-rcc", "syscon";
reg = <0x50000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
-
clock-names = "hse", "hsi", "csi", "lse", "lsi";
- clocks = <&clk_hse>, <&clk_hsi>, <&clk_csi>,
- <&clk_lse>, <&clk_lsi>;
+ clocks = <&scmi0_clk CK_SCMI0_HSE>,
+ <&scmi0_clk CK_SCMI0_HSI>,
+ <&scmi0_clk CK_SCMI0_CSI>,
+ <&scmi0_clk CK_SCMI0_LSE>,
+ <&scmi0_clk CK_SCMI0_LSI>;
};
+ // TODO: remove once under SCMI
pwr_regulators: pwr@50001000 {
compatible = "st,stm32mp1,pwr-reg";
reg = <0x50001000 0x10>;
@@ -1333,8 +1367,8 @@
compatible = "st,stm32f756-hash";
reg = <0x54002000 0x400>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&rcc HASH1>;
- resets = <&rcc HASH1_R>;
+ clocks = <&scmi0_clk CK_SCMI0_HASH1>;
+ resets = <&scmi0_reset RST_SCMI0_HASH1>;
dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
dma-names = "in";
dma-maxburst = <2>;
@@ -1344,8 +1378,8 @@
rng1: rng@54003000 {
compatible = "st,stm32-rng";
reg = <0x54003000 0x400>;
- clocks = <&rcc RNG1_K>;
- resets = <&rcc RNG1_R>;
+ clocks = <&scmi0_clk CK_SCMI0_RNG1>;
+ resets = <&scmi0_reset RST_SCMI0_RNG1>;
status = "disabled";
};
@@ -1354,7 +1388,7 @@
reg = <0x58000000 0x1000>;
interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc MDMA>;
- resets = <&rcc MDMA_R>;
+ resets = <&scmi0_reset RST_SCMI0_MDMA>;
#dma-cells = <5>;
dma-channels = <32>;
dma-requests = <48>;
@@ -1517,7 +1551,7 @@
iwdg2: watchdog@5a002000 {
compatible = "st,stm32mp1-iwdg";
reg = <0x5a002000 0x400>;
- clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
+ clocks = <&rcc IWDG2>, <&scmi0_clk CK_SCMI0_LSI>;
clock-names = "pclk", "lsi";
status = "disabled";
};
@@ -1549,7 +1583,7 @@
compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>;
interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&rcc USART1_K>;
+ clocks = <&scmi0_clk CK_SCMI0_USART1>;
wakeup-source;
status = "disabled";
};
@@ -1560,8 +1594,8 @@
compatible = "st,stm32h7-spi";
reg = <0x5c001000 0x400>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&rcc SPI6_K>;
- resets = <&rcc SPI6_R>;
+ clocks = <&scmi0_clk CK_SCMI0_SPI6>;
+ resets = <&scmi0_reset RST_SCMI0_SPI6>;
dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
<&mdma1 35 0x0 0x40002 0x0 0x0>;
dma-names = "rx", "tx";
@@ -1574,8 +1608,8 @@
interrupt-names = "event", "error";
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&rcc I2C4_K>;
- resets = <&rcc I2C4_R>;
+ clocks = <&scmi0_clk CK_SCMI0_I2C4>;
+ resets = <&scmi0_reset RST_SCMI0_I2C4>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x8>;
@@ -1587,7 +1621,8 @@
rtc: rtc@5c004000 {
compatible = "st,stm32mp1-rtc";
reg = <0x5c004000 0x400>;
- clocks = <&rcc RTCAPB>, <&rcc RTC>;
+ clocks = <&scmi0_clk CK_SCMI0_RTCAPB>,
+ <&scmi0_clk CK_SCMI0_RTC>;
clock-names = "pclk", "rtc_ck";
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -1615,8 +1650,8 @@
interrupt-names = "event", "error";
interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&rcc I2C6_K>;
- resets = <&rcc I2C6_R>;
+ clocks = <&scmi0_clk CK_SCMI0_I2C6>;
+ resets = <&scmi0_reset RST_SCMI0_I2C6>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x20>;
@@ -1782,7 +1817,7 @@
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x400>;
- clocks = <&rcc GPIOZ>;
+ clocks = <&scmi0_clk CK_SCMI0_GPIOZ>;
st,bank-name = "GPIOZ";
st,bank-ioport = <11>;
status = "disabled";
@@ -1804,9 +1839,9 @@
reg = <0x10000000 0x40000>,
<0x30000000 0x40000>,
<0x38000000 0x10000>;
- resets = <&rcc MCU_R>;
- st,syscfg-holdboot = <&rcc 0x10C 0x1>;
- st,syscfg-tz = <&rcc 0x000 0x1>;
+ resets = <&scmi0_reset RST_SCMI0_MCU>,
+ <&scmi0_reset RST_SCMI0_MCU_HOLD_BOOT>;
+ reset-names = "mcu_rst", "hold_boot";
st,syscfg-pdds = <&pwr_mcu 0x0 0x1>;
st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>;
st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>;
diff --git a/arch/arm/dts/stm32mp153.dtsi b/arch/arm/dts/stm32mp153.dtsi
index 1c1889b194..e9ba6a9f30 100644
--- a/arch/arm/dts/stm32mp153.dtsi
+++ b/arch/arm/dts/stm32mp153.dtsi
@@ -13,6 +13,8 @@
clock-frequency = <650000000>;
device_type = "cpu";
reg = <1>;
+ clocks = <&scmi0_clk CK_SCMI0_MPU>;
+ clock-names = "cpu";
};
};
@@ -30,7 +32,7 @@
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "int0", "int1";
- clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+ clocks = <&scmi0_clk CK_SCMI0_HSE>, <&rcc FDCAN_K>;
clock-names = "hclk", "cclk";
bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
status = "disabled";
@@ -43,7 +45,7 @@
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "int0", "int1";
- clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+ clocks = <&scmi0_clk CK_SCMI0_HSE>, <&rcc FDCAN_K>;
clock-names = "hclk", "cclk";
bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
status = "disabled";
diff --git a/arch/arm/dts/stm32mp157.dtsi b/arch/arm/dts/stm32mp157.dtsi
index 54e73ccea4..7b06c08e3a 100644
--- a/arch/arm/dts/stm32mp157.dtsi
+++ b/arch/arm/dts/stm32mp157.dtsi
@@ -20,7 +20,7 @@
dsi: dsi@5a000000 {
compatible = "st,stm32-dsi";
reg = <0x5a000000 0x800>;
- clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>;
+ clocks = <&rcc DSI_K>, <&scmi0_clk CK_SCMI0_HSE>, <&rcc
DSI_PX>;
clock-names = "pclk", "ref", "px_clk";
resets = <&rcc DSI_R>;
reset-names = "apb";
diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
index 15a04ae927..9e1c9c0329 100644
--- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
@@ -31,6 +31,7 @@
/* only needed for boot with TF-A, witout FIP support */
firmware {
optee {
+ u-boot,dm-pre-reloc;
compatible = "linaro,optee-tz";
method = "smc";
};
@@ -38,8 +39,10 @@
reserved-memory {
u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
optee@de000000 {
+ u-boot,dm-pre-reloc;
reg = <0xde000000 0x02000000>;
no-map;
u-boot,dm-spl;
@@ -61,117 +64,6 @@
status = "okay";
};
-&clk_hse {
- st,digbypass;
-};
-
-&i2c4 {
- u-boot,dm-pre-reloc;
-};
-
-&i2c4_pins_a {
- u-boot,dm-pre-reloc;
- pins {
- u-boot,dm-pre-reloc;
- };
-};
-
-&pmic {
- u-boot,dm-pre-reloc;
-};
-
-&rcc {
- st,clksrc = <
- CLK_MPU_PLL1P
- CLK_AXI_PLL2P
- CLK_MCU_PLL3P
- CLK_PLL12_HSE
- CLK_PLL3_HSE
- CLK_PLL4_HSE
- CLK_RTC_LSE
- CLK_MCO1_DISABLED
- CLK_MCO2_DISABLED
- >;
-
- st,clkdiv = <
- 1 /*MPU*/
- 0 /*AXI*/
- 0 /*MCU*/
- 1 /*APB1*/
- 1 /*APB2*/
- 1 /*APB3*/
- 1 /*APB4*/
- 2 /*APB5*/
- 23 /*RTC*/
- 0 /*MCO1*/
- 0 /*MCO2*/
- >;
-
- st,pkcs = <
- CLK_CKPER_HSE
- CLK_FMC_ACLK
- CLK_QSPI_ACLK
- CLK_ETH_DISABLED
- CLK_SDMMC12_PLL4P
- CLK_DSI_DSIPLL
- CLK_STGEN_HSE
- CLK_USBPHY_HSE
- CLK_SPI2S1_PLL3Q
- CLK_SPI2S23_PLL3Q
- CLK_SPI45_HSI
- CLK_SPI6_HSI
- CLK_I2C46_HSI
- CLK_SDMMC3_PLL4P
- CLK_USBO_USBPHY
- CLK_ADC_CKPER
- CLK_CEC_LSE
- CLK_I2C12_HSI
- CLK_I2C35_HSI
- CLK_UART1_HSI
- CLK_UART24_HSI
- CLK_UART35_HSI
- CLK_UART6_HSI
- CLK_UART78_HSI
- CLK_SPDIF_PLL4P
- CLK_FDCAN_PLL4R
- CLK_SAI1_PLL3Q
- CLK_SAI2_PLL3Q
- CLK_SAI3_PLL3Q
- CLK_SAI4_PLL3Q
- CLK_RNG1_LSI
- CLK_RNG2_LSI
- CLK_LPTIM1_PCLK1
- CLK_LPTIM23_PCLK3
- CLK_LPTIM45_LSE
- >;
-
- /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
- pll2: st,pll@1 {
- compatible = "st,stm32mp1-pll";
- reg = <1>;
- cfg = < 2 65 1 0 0 PQR(1,1,1) >;
- frac = < 0x1400 >;
- u-boot,dm-pre-reloc;
- };
-
- /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
- pll3: st,pll@2 {
- compatible = "st,stm32mp1-pll";
- reg = <2>;
- cfg = < 1 33 1 16 36 PQR(1,1,1) >;
- frac = < 0x1a04 >;
- u-boot,dm-pre-reloc;
- };
-
- /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
- pll4: st,pll@3 {
- compatible = "st,stm32mp1-pll";
- reg = <3>;
- cfg = < 3 98 5 7 7 PQR(1,1,1) >;
- u-boot,dm-pre-reloc;
- };
-};
-
&sdmmc1 {
u-boot,dm-spl;
};
diff --git a/arch/arm/dts/stm32mp157c-dk2-u-boot.dtsi
b/arch/arm/dts/stm32mp157c-dk2-u-boot.dtsi
index 06ef3a4095..9f9979dc5f 100644
--- a/arch/arm/dts/stm32mp157c-dk2-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157c-dk2-u-boot.dtsi
@@ -4,3 +4,43 @@
*/
#include "stm32mp157a-dk1-u-boot.dtsi"
+
+&optee {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+};
+
+&scmi0 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+};
+
+&scmi0_clk {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi0_reset {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi0_shm {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi1 {
+ status = "disabled";
+ u-boot,dm-pre-reloc;
+};
+
+&scmi1_clk {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi1_shm {
+ u-boot,dm-pre-reloc;
+};
+
+&scmi_sram {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/stm32mp157c-dk2.dts b/arch/arm/dts/stm32mp157c-dk2.dts
index 2bc92ef3ae..fb9300fcb1 100644
--- a/arch/arm/dts/stm32mp157c-dk2.dts
+++ b/arch/arm/dts/stm32mp157c-dk2.dts
@@ -99,3 +99,12 @@
pinctrl-2 = <&usart2_idle_pins_c>;
status = "disabled";
};
+
+&optee {
+ status = "okay";
+};
+
+&scmi0 {
+ compatible = "linaro,scmi-optee";
+ status = "okay";
+};
diff --git a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
index 408abaf52f..e2e1769d97 100644
--- a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
@@ -32,6 +32,8 @@
optee {
compatible = "linaro,optee-tz";
method = "smc";
+ u-boot,dm-pre-reloc;
+ status = "okay";
};
};
@@ -39,6 +41,7 @@
optee@fe000000 {
reg = <0xfe000000 0x02000000>;
no-map;
+ u-boot,dm-pre-reloc;
};
};
#endif
@@ -53,10 +56,6 @@
};
};
-&clk_hse {
- st,digbypass;
-};
-
&i2c4 {
u-boot,dm-pre-reloc;
};
@@ -72,98 +71,6 @@
u-boot,dm-pre-reloc;
};
-&rcc {
- st,clksrc = <
- CLK_MPU_PLL1P
- CLK_AXI_PLL2P
- CLK_MCU_PLL3P
- CLK_PLL12_HSE
- CLK_PLL3_HSE
- CLK_PLL4_HSE
- CLK_RTC_LSE
- CLK_MCO1_DISABLED
- CLK_MCO2_DISABLED
- >;
-
- st,clkdiv = <
- 1 /*MPU*/
- 0 /*AXI*/
- 0 /*MCU*/
- 1 /*APB1*/
- 1 /*APB2*/
- 1 /*APB3*/
- 1 /*APB4*/
- 2 /*APB5*/
- 23 /*RTC*/
- 0 /*MCO1*/
- 0 /*MCO2*/
- >;
-
- st,pkcs = <
- CLK_CKPER_HSE
- CLK_FMC_ACLK
- CLK_QSPI_ACLK
- CLK_ETH_DISABLED
- CLK_SDMMC12_PLL4P
- CLK_DSI_DSIPLL
- CLK_STGEN_HSE
- CLK_USBPHY_HSE
- CLK_SPI2S1_PLL3Q
- CLK_SPI2S23_PLL3Q
- CLK_SPI45_HSI
- CLK_SPI6_HSI
- CLK_I2C46_HSI
- CLK_SDMMC3_PLL4P
- CLK_USBO_USBPHY
- CLK_ADC_CKPER
- CLK_CEC_LSE
- CLK_I2C12_HSI
- CLK_I2C35_HSI
- CLK_UART1_HSI
- CLK_UART24_HSI
- CLK_UART35_HSI
- CLK_UART6_HSI
- CLK_UART78_HSI
- CLK_SPDIF_PLL4P
- CLK_FDCAN_PLL4R
- CLK_SAI1_PLL3Q
- CLK_SAI2_PLL3Q
- CLK_SAI3_PLL3Q
- CLK_SAI4_PLL3Q
- CLK_RNG1_LSI
- CLK_RNG2_LSI
- CLK_LPTIM1_PCLK1
- CLK_LPTIM23_PCLK3
- CLK_LPTIM45_LSE
- >;
-
- /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
- pll2: st,pll@1 {
- compatible = "st,stm32mp1-pll";
- reg = <1>;
- cfg = < 2 65 1 0 0 PQR(1,1,1) >;
- frac = < 0x1400 >;
- u-boot,dm-pre-reloc;
- };
-
- /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
- pll3: st,pll@2 {
- compatible = "st,stm32mp1-pll";
- reg = <2>;
- cfg = < 1 33 1 16 36 PQR(1,1,1) >;
- frac = < 0x1a04 >;
- u-boot,dm-pre-reloc;
- };
-
- /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
- pll4: st,pll@3 {
- compatible = "st,stm32mp1-pll";
- reg = <3>;
- cfg = < 3 98 5 7 7 PQR(1,1,1) >;
- u-boot,dm-pre-reloc;
- };
-};
-
&sdmmc1 {
u-boot,dm-spl;
};
diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts
index 6e89f88a17..eabf00f1fe 100644
--- a/arch/arm/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/dts/stm32mp157c-ed1.dts
@@ -341,6 +341,11 @@
status = "okay";
};
+&scmi0 {
+ compatible = "linaro,scmi-optee";
+ status = "okay";
+};
+
&sdmmc1 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
diff --git a/arch/arm/dts/stm32mp157c-odyssey.dts
b/arch/arm/dts/stm32mp157c-odyssey.dts
index 0e725498dd..9823d5d5ca 100644
--- a/arch/arm/dts/stm32mp157c-odyssey.dts
+++ b/arch/arm/dts/stm32mp157c-odyssey.dts
@@ -21,6 +21,20 @@
stdout-path = "serial0:115200n8";
};
+ clocks {
+ clk_hse: clk-hse {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ clk_lse: clk-lse {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+ };
+
led {
compatible = "gpio-leds";
blue {
diff --git a/arch/arm/dts/stm32mp15xc.dtsi b/arch/arm/dts/stm32mp15xc.dtsi
index b06a55a2fa..435846883f 100644
--- a/arch/arm/dts/stm32mp15xc.dtsi
+++ b/arch/arm/dts/stm32mp15xc.dtsi
@@ -10,8 +10,8 @@
compatible = "st,stm32mp1-cryp";
reg = <0x54001000 0x400>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&rcc CRYP1>;
- resets = <&rcc CRYP1_R>;
+ clocks = <&scmi0_clk CK_SCMI0_CRYP1>;
+ resets = <&scmi0_reset RST_SCMI0_CRYP1>;
status = "disabled";
};
};
diff --git a/include/dt-bindings/clock/stm32mp1-clks.h
b/include/dt-bindings/clock/stm32mp1-clks.h
index 4cdaf13582..e02770b98e 100644
--- a/include/dt-bindings/clock/stm32mp1-clks.h
+++ b/include/dt-bindings/clock/stm32mp1-clks.h
@@ -248,4 +248,31 @@
#define STM32MP1_LAST_CLK 232
+/* SCMI clock identifiers */
+#define CK_SCMI0_HSE 0
+#define CK_SCMI0_HSI 1
+#define CK_SCMI0_CSI 2
+#define CK_SCMI0_LSE 3
+#define CK_SCMI0_LSI 4
+#define CK_SCMI0_PLL2_Q 5
+#define CK_SCMI0_PLL2_R 6
+#define CK_SCMI0_MPU 7
+#define CK_SCMI0_AXI 8
+#define CK_SCMI0_BSEC 9
+#define CK_SCMI0_CRYP1 10
+#define CK_SCMI0_GPIOZ 11
+#define CK_SCMI0_HASH1 12
+#define CK_SCMI0_I2C4 13
+#define CK_SCMI0_I2C6 14
+#define CK_SCMI0_IWDG1 15
+#define CK_SCMI0_RNG1 16
+#define CK_SCMI0_RTC 17
+#define CK_SCMI0_RTCAPB 18
+#define CK_SCMI0_SPI6 19
+#define CK_SCMI0_USART1 20
+
+#define CK_SCMI1_PLL3_Q 0
+#define CK_SCMI1_PLL3_R 1
+#define CK_SCMI1_MCU 2
+
#endif /* _DT_BINDINGS_STM32MP1_CLKS_H_ */
diff --git a/include/dt-bindings/reset/stm32mp1-resets.h
b/include/dt-bindings/reset/stm32mp1-resets.h
index 702da37a2e..f3a0ed3178 100644
--- a/include/dt-bindings/reset/stm32mp1-resets.h
+++ b/include/dt-bindings/reset/stm32mp1-resets.h
@@ -106,4 +106,18 @@
#define GPIOJ_R 19785
#define GPIOK_R 19786
+/* SCMI reset domain identifiers */
+#define RST_SCMI0_SPI6 0
+#define RST_SCMI0_I2C4 1
+#define RST_SCMI0_I2C6 2
+#define RST_SCMI0_USART1 3
+#define RST_SCMI0_STGEN 4
+#define RST_SCMI0_GPIOZ 5
+#define RST_SCMI0_CRYP1 6
+#define RST_SCMI0_HASH1 7
+#define RST_SCMI0_RNG1 8
+#define RST_SCMI0_MDMA 9
+#define RST_SCMI0_MCU 10
+#define RST_SCMI0_MCU_HOLD_BOOT 11
+
#endif /* _DT_BINDINGS_STM32MP1_RESET_H_ */
--
2.17.1
