On 2021/8/6 17:56, Michael Nazzareno Trimarchi wrote:
Hi Ye

On Thu, Jul 15, 2021 at 10:19 AM Michael Nazzareno Trimarchi
<mich...@amarulasolutions.com> wrote:

Hi

On Thu, Jul 15, 2021 at 9:56 AM Ye Li <ye...@nxp.com> wrote:

Hi Michael,

-----Original Message-----
From: Michael Nazzareno Trimarchi <mich...@amarulasolutions.com>
Sent: Thursday, July 15, 2021 2:52 PM
To: Peng Fan (OSS) <peng....@oss.nxp.com>
Cc: Peng Fan <peng....@nxp.com>; U-Boot-Denx <u-boot@lists.denx.de>;
Stefano Babic <sba...@denx.de>; Ye Li <ye...@nxp.com>; Fabio Estevam
<feste...@gmail.com>; Jagan Teki <ja...@amarulasolutions.com>
Subject: [EXT] Re: Problem on imx: add rom api support on imx8mn

Caution: EXT Email

Hi

On Thu, Jul 15, 2021 at 8:47 AM Peng Fan (OSS) <peng....@oss.nxp.com>
wrote:



On 2021/7/8 17:15, Michael Nazzareno Trimarchi wrote:
Hi Peng

On Thu, Jul 8, 2021 at 9:12 AM Peng Fan (OSS) <peng....@oss.nxp.com>
wrote:

On 2021/7/4 1:24, Michael Nazzareno Trimarchi wrote:
Hi all

I have some problems that I have understood and fixed but I can
not explain. Right now I have on imx8mn that can boot from boot0
or boot1 partition after remove a condition in the
is_boot_from_stream_device

This is a boot from mmcblk0boot0 with some debug

U-Boot SPL 2020.04-5.4.70-2.3.2+gf3bcbdfc62 (Jul 03 2021 -
17:00:27 +0000) power_bd71837_init
DDRINFO: start DRAM init
DDRINFO: DRAM rate 1600MTS
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Trying to boot from BOOTROM
ROM API interface 2 from boot 131073

Interface is 2 MMC and boot is 131073 and according to this

static int is_boot_from_stream_device(u32 boot)
+{
+       u32 interface;
+
+       interface = boot >> 16;
+       if (interface >= BT_DEV_TYPE_USB)
+               return 1;
+
+       if (interface == BT_DEV_TYPE_MMC && (boot & 1))
+               return 1;
+
+       return 0;
+}

means a stream interface but it does not boot.

Boot from boot1 give 131072 that is boot1 this let device boot
because

Who gives 131073? Boot from boot1, you mean emmc boot partition0?

is_boot_from_stream_device is 0 and romapi use
spl_romapi_load_image_seekable

Remove boot & 1 condition let me boot from mmcblk0boot0 and
mmcblk0boot1 without any problem

Have you enabled emmc fastboot in fuse?

boot & 1 is checking emmc fastboot. emmc fastboot mode is actually
stream device. If fastboot mode enabled, you need burn your
flash.bin into offset 0. Not 32KB offset.

The offset is correct and the spl is starting on boot0 but then it
should load the rest from
boot0 block and not from usb. And why in case of boot1 the 1 is not
present. I flash both on offset 0. Anyway I sent a patch

I suspect you have eMMC fastboot enabled for boot0, but not for boot1.

I think that was fuse this way

# Alternative Boot ("Fast boot")
# =>[BT_FUSE_SEL | eMMC boot | USDHC1 EMMC]
FB: ucmd fuse prog -y 1 3 0x10002A00
# =>[Fast boot | 8-bit DDR | MMC High speed | 1.8V | eMMC reset enable]
FB: ucmd fuse prog -y 2 1 0x000000E7
# =>[Fast Boot Ack enable]
FB: ucmd fuse prog -y 2 2 0x00000001
# boot_bus_width: 2 (8-bit), reset_boot_bus_width: 0, boot_mode: 2 (use dual
data rate (DDR))
FB: ucmd mmc bootbus 0 2 0 2
# boot_ack: 1, boot_partition: 1 (Boot partition 1), 7 (User area),
partition_access: No access to boot partition (default)
FB: ucmd mmc partconf 0 1 1 0

How is it supposed to work in this case?


Above settings use the boot0 for fastboot. When you switch to boot1 for 
fastboot, did you change the
partconf setting to "mmc partconf 0 1 2 0"?

I don't need to use fastboot. I mean the idea is if I boot from block0
I want to continue there. BOOTROM
fill the mode but then it should be able to not fail. Am I right?


If the ROM boots from emmc fastboot, it will set the bit0 to 1 to indicate the 
fastboot. Since at this time, ROM
does not leave fastboot (just stop the clock), we should continue the stream 
mode read in SPL for FIT image load.
So below checking is correct.  If you continue the stream mode read, what is 
the failure do you meet?
The codes will read max 640KB data from ROM to search to FIT header. Can it get 
the header or not?


It does not find the header, in this case and it's not  problem of
size of 640Kb (I have extend it). My impression
is that is loading from mmcblk0 and not boot partition

U-Boot SPL 2020.04-00190-g4bad07fb61-dirty (Aug 06 2021 - 11:38:18 +0200)
spl_init
power_bd71837_init
DDRINFO: start DRAM init
DDRINFO: DRAM rate 1600MTS
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
SPL: board_init_r()
Normal Boot
Trying to boot from BOOTROM
ROM API interface 2 from boot 131073
Can't found uboot FIT image in 640K range
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

This is my error but if I continue stream mode but it works in seakble mode.

stream mode is only effective when usb download and eMMC fastboot.

Note eMMC fastboot, needs both set eMMC chip and SoC fuse(or boot switch)

Otherwise, there is bug somewhere.

Regards,
Peng.

2 is the MMC and boot mode is 131073

Michael


Michael

         if (interface == BT_DEV_TYPE_MMC && (boot & 1))
                 return 1;

Best regards,
Ye Li

Michael




Regards,
Peng.


Michael


Regards,
Peng.


mmc partconf 0
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x0
BOOT_PARTITION_ENABLE: 0x1
PARTITION_ACCESS: 0x0

and the board was fused already.

Any idea why?

Michael







--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
mich...@amarulasolutions.com
__________________________________

Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172
i...@amarulasolutions.com
https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.ama%2F&amp;data=04%7C01%7Cpeng.fan%40nxp.com%7Cf865f9a2910d45fa445f08d958c07a17%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637638405967351694%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&amp;sdata=y%2Fj1UGXJIzqV4A2mbyse8GhQbFXejyplQwsd6xYbIbs%3D&amp;reserved=0
rulasolutions.com%2F&amp;data=04%7C01%7Cye.li%40nxp.com%7C1e6a78bc
a6d441c39f8608d9475d2495%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%
7C0%7C637619287640324977%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wL
jAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&amp;s
data=xIsVMyj9Qp1vciZnjJJK1wAT7A8fLdNRAs9pp4tll%2F0%3D&amp;reserved=
0



--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
mich...@amarulasolutions.com
__________________________________

Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
i...@amarulasolutions.com
https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.amarulasolutions.com%2F&amp;data=04%7C01%7Cpeng.fan%40nxp.com%7Cf865f9a2910d45fa445f08d958c07a17%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637638405967351694%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&amp;sdata=M6K%2FtGU2BF3wBoNT9U722IgtKb47VXkW%2Fd8aGYjAXGY%3D&amp;reserved=0



Reply via email to