On 5/25/21 6:02 PM, Patrice CHOTARD wrote:
> Hi Daniil
>
> On 5/24/21 2:53 PM, Daniil Stas wrote:
>> On Mon, 24 May 2021 09:40:05 +0200
>> Patrice CHOTARD <patrice.chot...@foss.st.com> wrote:
>>
>>> Hi Daniil
>>>
>>> On 5/24/21 12:24 AM, Daniil Stas wrote:
>>>> TCF flag only means that all data was sent to FIFO. To check if the
>>>> data was sent out of FIFO we should also wait for the BUSY flag to
>>>> be cleared. Otherwise there is a race condition which can lead to
>>>> inability to write short (one byte long) data.
>>>>
>>>> Signed-off-by: Daniil Stas <daniil.s...@posteo.net>
>>>> Cc: Patrick Delaunay <patrick.delau...@foss.st.com>
>>>> Cc: Patrice Chotard <patrice.chot...@foss.st.com>
>>>> ---
>>>> drivers/spi/stm32_qspi.c | 29 +++++++++++++++--------------
>>>> 1 file changed, 15 insertions(+), 14 deletions(-)
>>>>
>>>> diff --git a/drivers/spi/stm32_qspi.c b/drivers/spi/stm32_qspi.c
>>>> index 4acc9047b9..8f4aabc3d1 100644
>>>> --- a/drivers/spi/stm32_qspi.c
>>>> +++ b/drivers/spi/stm32_qspi.c
>>>> @@ -148,23 +148,24 @@ static int _stm32_qspi_wait_cmd(struct
>>>> stm32_qspi_priv *priv, const struct spi_mem_op *op)
>>>> {
>>>> u32 sr;
>>>> - int ret;
>>>> -
>>>> - if (!op->data.nbytes)
>>>> - return _stm32_qspi_wait_for_not_busy(priv);
>>>> + int ret = 0;
>>>>
>>>> - ret = readl_poll_timeout(&priv->regs->sr, sr,
>>>> - sr & STM32_QSPI_SR_TCF,
>>>> - STM32_QSPI_CMD_TIMEOUT_US);
>>>> - if (ret) {
>>>> - log_err("cmd timeout (stat:%#x)\n", sr);
>>>> - } else if (readl(&priv->regs->sr) & STM32_QSPI_SR_TEF) {
>>>> - log_err("transfer error (stat:%#x)\n", sr);
>>>> - ret = -EIO;
>>>> + if (op->data.nbytes) {
>>>> + ret = readl_poll_timeout(&priv->regs->sr, sr,
>>>> + sr & STM32_QSPI_SR_TCF,
>>>> +
>>>> STM32_QSPI_CMD_TIMEOUT_US);
>>>> + if (ret) {
>>>> + log_err("cmd timeout (stat:%#x)\n", sr);
>>>> + } else if (readl(&priv->regs->sr) &
>>>> STM32_QSPI_SR_TEF) {
>>>> + log_err("transfer error (stat:%#x)\n", sr);
>>>> + ret = -EIO;
>>>> + }
>>>> + /* clear flags */
>>>> + writel(STM32_QSPI_FCR_CTCF | STM32_QSPI_FCR_CTEF,
>>>> &priv->regs->fcr); }
>>>>
>>>> - /* clear flags */
>>>> - writel(STM32_QSPI_FCR_CTCF | STM32_QSPI_FCR_CTEF,
>>>> &priv->regs->fcr);
>>>> + if (!ret)
>>>> + ret = _stm32_qspi_wait_for_not_busy(priv);
>>>>
>>>> return ret;
>>>> }
>>>>
>>>
>>> Have you got a simple test to reproduce the described race condition ?
>>>
>>> Thanks
>>> Patrice
>>
>> Hi, Patrice
>>
>> I found this issue on an stm32mp153 based board.
>> To reproduce it you need to set qspi peripheral clock to a low
>> value (for example 24 MHz).
>> Then you can test it in the u-boot console:
>>
>> STM32MP> clk dump
>> Clocks:
>> ...
>> - CK_PER : 24 MHz
>> ...
>> - QSPI(10) => parent CK_PER(30)
>> ...
>>
>> STM32MP> sf probe
>> SF: Detected w25q32jv with page size 256 Bytes, erase size 64 KiB, total 4
>> MiB
>> STM32MP> sf erase 0x00300000 +1
>> SF: 65536 bytes @ 0x300000 Erased: OK
>> STM32MP> sf read 0xc4100000 0x300000 10
>> device 0 offset 0x300000, size 0x10
>> SF: 16 bytes @ 0x300000 Read: OK
>> STM32MP> md.b 0xc4100000
>> c4100000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
>> ...
>> STM32MP> mw.b 0xc4200000 55
>> STM32MP> sf write 0xc4200000 0x00300000 1
>> device 0 offset 0x300000, size 0x1
>> SF: 1 bytes @ 0x300000 Written: OK
>> STM32MP> sf read 0xc4100000 0x00300000 10
>> device 0 offset 0x300000, size 0x10
>> SF: 16 bytes @ 0x300000 Read: OK
>> STM32MP> md.b 0xc4100000
>> c4100000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
>> ...
>>
>>
>> With my patch applied the last command result would be:
>> STM32MP> md.b 0xc4100000
>> c4100000: 55 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff U...............
>>
>> Thanks,
>> Daniil
>>
>
> Thanks for the detailed informations, i also reproduced this issue on a
> stm32mp157c-ev1 board.
>
> Reviewed-by: Patrice Chotard <patrice.chot...@foss.st.com>
>
> Patrice
>
>
Applied on u-boot-stm32/next
Thanks
