Hi,
this has been put aside for a while but tested this again and problem
still remains for me.
Hi,
I'm following the README
to bring up u-boot on a imx8mp EVK board. My
boot ends up in this on the
console:
U-Boot SPL 2020.10-rc5-00049-gd44d46e9fa (Sep 30 2020 - 11:46:20 +0200)
Normal Boot
WDT: Started with servicing (60s timeout)
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Can't support legacy image
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Any ideas what is going wrong? How to debug further?
I am trying to port U-Boot to an i.MX8M Nano and I am getting the same result.
This might not be related, but looking at the ATF branch [imx_5.4.3_2.0.0] - it
appears to be too old, at least for i.MX8M Plus. I was able to run the U-Boot
2020.10 with ATF built from [imx_5.4.47_2.2.0] on the i.MX8M Plus and it does
boot successful.
Boot log show the following banner when BOOTROM finishes up the copy:
NOTICE: BL31: v2.2(release):rel_imx_5.4.47_2.2.0-0-gc949a888e-dirty
NOTICE: BL31: Built : 05:51:50, Sep 9 2020
Peter,
i.MX8M Plus support in NXP ATF fork appears to be added by commit
https://source.codeaurora.org/external/imx/imx-atf/commit/?id=6b8249ff58cc8853396498a074535dcd7f81beaf,
and that came in ATF revision far newer than indicated in
doc/board/freescale/imx8mp_evk.rst
Try to rebase your ATF to [c949a888e909811db191500c51456391dff61284] and build
according to the board doc file.
Andrey, Thanks for advice about the commit in imx-atf. Unfortunately it
does not seem to solve the issue.
This is what I tested today and where I ended up today:
$ cd imx-atf
$ git checkout imx_5.4.70_2.3.0
$ make PLAT=imx8mp bl31
$ cd ../u-boot
$ git checkout master (80c7e4cf76d204d4b726b0cc57a557a9d9c1c453)
$ cp ../imx-atf/build/imx8mp/release/bl31.bin .
$ cp
../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_202006.bin
lpddr4_pmu_train_1d_dmem.bin
$ cp
../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin
lpddr4_pmu_train_1d_imem.bin
$ cp
../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin
lpddr4_pmu_train_2d_dmem.bin
$ cp
../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_202006.bin
lpddr4_pmu_train_2d_imem.bin
$ export ATF_LOAD_ADDR=0x960000
$ make imx8mp_evk_defconfig
$ make flash.bin
$ sudo dd if=flash.bin of=/dev/mmcblk0 bs=1024 seek=32
When booting on a imx8mp EVK from NXP the console shows me this:
U-Boot SPL 2020.04-00033-g633977d904 (Feb 12 2021 - 08:12:50 +0100)
DDRINFO: start DRAM init
DDRINFO: DRAM rate 4000MTS
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Can't support legacy image
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The code that fails is in arch/arm/mach-imx/spl_imx_romapi.c
if (IS_ENABLED(CONFIG_SPL_LOAD_FIT) &&
image_get_magic(header) == FDT_MAGIC) {
....
} else {
/* TODO */
puts("Can't support legacy image\n");
return -1;
}
I have traced out 'image_get_magic(header)' on the console and it is a
new random value at each power on. I can also note that I have tested
branch imx_v2020.04_5.4.70_2.3.0 from from uboot-imx ending up in the
same result on the console.
Anyone that have ideas here how to proceed and where the problem can be?
Anyone with a imx8mp EVK on the desk that succeed with building and
deploying u-boot on a SD card and can share the workflow?
Best regards,
/Peter
