Hi Vagrant,
Do you know which version is the last version that works in this case?
The firmware is from eMMC and it's wired for USB to affect the boot
process.
Thanks,
- Kever
On 2021/1/21 上午8:08, Vagrant Cascadian wrote:
It seems rockpro64-rk3399 and pinebook-pro-rk3399 fail to boot when usb
is started. It hangs indefinitely at:
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
I have observed this also using 2020.10 on rockpro64-rk3399, though on
pinebook-pro-rk3399 usb does not work and so it basically avoids
triggering the issue.
Setting CONFIG_USE_PREBOOT=n in the config works around the problem,
though obviously by breaking usb keyboard support or booting from USB
devices.
Related bugs in Debian and manjaro:
https://bugs.debian.org/973323
https://bugs.debian.org/980434
https://gitlab.manjaro.org/manjaro-arm/packages/core/uboot-rockpro64/-/issues/4
Boot log:
U-Boot 2021.01+dfsg-1 (Jan 17 2021 - 03:50:13 +0000)
SoC: Rockchip rk3399
Reset cause: POR
Model: Pine64 RockPro64 v2.1
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256
Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Pine64 RockPro64 v2.1
Net: eth0: ethernet@fe300000
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
=> printenv preboot
preboot=usb start
=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> boot
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
144 bytes read in 5 ms (27.3 KiB/s)
1: Debian-Installer
Retrieving file: /initrd.gz
28995285 bytes read in 1287 ms (21.5 MiB/s)
Retrieving file: /vmlinuz
26922864 bytes read in 1195 ms (21.5 MiB/s)
Retrieving file: /dtbs/rockchip/rk3399-rockpro64.dtb
56849 bytes read in 13 ms (4.2 MiB/s)
Moving Image from 0x2080000 to 0x2200000, end=3c50000
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
live well,
vagrant
