Hi Priyanka,
On Mon, Sep 7, 2020 at 2:26 PM Priyanka Jain <priyanka.j...@nxp.com> wrote:
> Hello Rayagonda,
>
>
>
> With today top of upstream u-boot tree, I am still getting the error in
> booting lx216ardb
>
>
>
> U-Boot 2020.10-rc3-00086-ge5df264e7a (Sep 07 2020 - 14:13:57 +0530)
>
> <snip>
>
> “Error binding driver 'gic-v3': -96
>
> Some drivers failed to bind
>
> initcall sequence 00000000fbdcf368 failed at call 000000008201b5e4
> (err=-96)
>
> ### ERROR ### Please RESET the board ###
>
>
>
> But if apply the changes suggested by you, it is booting fine. Can you
> please help to send the pull-request for this soon , so that proper fixes
> are integrated in u-boot code before U-boot v2020.10 release.
>
It was working for me long back without this patch.
Could you please send this patch as you can reproduce it and test it.
Please let me know.
Best regards,
Rayagonda
>
>
> Thanks
>
> Priyanka
>
>
>
> *From:* Rayagonda Kokatanur <rayagonda.kokata...@broadcom.com>
> *Sent:* Friday, September 4, 2020 10:50 PM
> *To:* Priyanka Jain <priyanka.j...@nxp.com>
> *Cc:* Z.q. Hou <zhiqiang....@nxp.com>; Wasim Khan <wasim.k...@nxp.com>;
> Bharat Gooty <bharat.go...@broadcom.com>; Manish Tomar <
> manish.to...@nxp.com>; Xiaobo Xie <xiaobo....@nxp.com>; Jiafei Pan <
> jiafei....@nxp.com>; Meenakshi Aggarwal <meenakshi.aggar...@nxp.com>
> *Subject:* Re: Change in gic_lpi_tables_init() function
>
>
>
> Hi Priyanka,
>
>
>
> Please add the following code at the end of "arch/arm/lib/gic-v3-its.c"
> file,
> This is not required for the latest uboot hence its not part of the patch.
>
> UCLASS_DRIVER(irq) = {
> .id = UCLASS_IRQ,
> .name = "irq",
> };
>
>
>
> Best regards,
>
> Rayagonda
>
>
>
>
>
> On Fri, Sep 4, 2020 at 9:38 PM Priyanka Jain <priyanka.j...@nxp.com>
> wrote:
>
> Hello Rayagonda,
>
>
>
> I am getting below error with top of tree upstream on lx2160ardb. Any
> pointer here.
>
>
>
> U-Boot 2020.10-rc3-00082-g9bfb567e5f (Sep 04 2020 - 21:27:29 +0530)
>
>
>
> SoC: LX2160ACE Rev2.0 (0x87360020)
>
> Clock Configuration:
>
> CPU0(A72):1900 MHz CPU1(A72):1900 MHz CPU2(A72):1900 MHz
>
> CPU3(A72):1900 MHz CPU4(A72):1900 MHz CPU5(A72):1900 MHz
>
> CPU6(A72):1900 MHz CPU7(A72):1900 MHz CPU8(A72):1900 MHz
>
> CPU9(A72):1900 MHz CPU10(A72):1900 MHz CPU11(A72):1900 MHz
>
> CPU12(A72):1900 MHz CPU13(A72):1900 MHz CPU14(A72):1900 MHz
>
> CPU15(A72):1900 MHz
>
> Bus: 600 MHz DDR: 2600 MT/s
>
> Reset Configuration Word (RCW):
>
> 00000000: 4c6b6b30 204c004c 00000000 00000000
>
> 00000010: 00000000 0c010000 00000000 00000000
>
> 00000020: 02e001a0 00002580 00000000 00000096
>
> 00000030: 00000000 00000000 00000000 00000000
>
> 00000040: 00000000 00000000 00000000 00000000
>
> 00000050: 00000000 00000000 00000000 00000000
>
> 00000060: 00000000 00000000 00027000 00000000
>
> 00000070: 08b30010 00150020
>
> Model: NXP Layerscape LX2160ARDB Board
>
> Board: LX2160ACE Rev2.0-RDB, Board version: B, boot from FlexSPI DEV#1
>
> FPGA: v5.0
>
> SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz
>
> SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz
>
> SERDES3 Reference: Clock1 = 100MHz Clock2 = 100MHz
>
> VID: Core voltage after adjustment is at 851 mV
>
> DRAM: 31.9 GiB
>
> DDR 31.9 GiB (DDR4, 64-bit, CL=19, ECC on)
>
> DDR Controller Interleaving Mode: 256B
>
> DDR Chip-Select Interleaving Mode: CS0+CS1
>
> Error binding driver 'gic-v3': -96
>
> Some drivers failed to bind
>
> initcall sequence 00000000fbdcf368 failed at call 000000008201b5e4
> (err=-96)
>
> ### ERROR ### Please RESET the board ###
>
>
>
> Regards
>
> Priyanka
>
>
