On 9/08/2010 5:57 AM, Wolfgang Denk wrote: > Dear Kumar Gala, > > In message<57cdb146-383a-4629-b7e4-c2729200a...@kernel.crashing.org> you > wrote: >> On Jun 23, 2010, at 8:56 AM, Poonam Aggrwal wrote: >> >>> This patch enables the eSPI configuration to use >>> the Spansion Flash on P1 and P2 RDB Platforms >>> >>> This also enables the Intel Pro/1000 PT Gb Ethernet >>> PCI-E Network Adapter configuration support >>> >>> Signed-off-by: Poonam Aggrwal<poonam.aggr...@freescale.com> >>> --- >>> include/configs/P1_P2_RDB.h | 15 +++++++++++++++ >>> 1 files changed, 15 insertions(+), 0 deletions(-) >> applied to 85xx > I think I haven't seen this in a pull request yet? > > Best regards, > > Wolfgang Denk >
I've been looking at past messages and I don't think the Freescale eSPI controller patch ever made it in. The most recent discussion I could find was here: http://lists.denx.de/pipermail/u-boot/2009-March/049114.html I'm not sure why exactly a driver like this needs the activate and deactivate functions as it's for a SoC, so I was wondering whether something like the below would not work? (this is just for discussion purposes so please disregard formatting). Index: a/u-boot/include/configs/P1_P2_RDB.h =================================================================== --- a/u-boot/include/configs/P1_P2_RDB.h +++ b/u-boot/include/configs/P1_P2_RDB.h @@ -97,6 +97,21 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE +#define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/ + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SPANSION + +#define CONFIG_HARD_SPI +#define CONFIG_FSL_ESPI + +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif Index: a/u-boot/drivers/spi/fsl_espi.c =================================================================== --- /dev/null +++ b/u-boot/drivers/spi/fsl_espi.c @@ -0,0 +1,225 @@ +/* + * eSPI controller driver. + * + * Copyright 2009 Freescale Semiconductor, Inc. + * Author: Mingkai Hu (mingkai...@freescale.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +#include <malloc.h> +#include <spi.h> +#include <asm/immap_85xx.h> + +#define ESPI_MAX_CS_NUM 4 + +#define ESPI_EV_RNE (1 << 9) +#define ESPI_EV_TNF (1 << 8) + +#define ESPI_MODE_EN (1 << 31) /* Enable interface */ +#define ESPI_MODE_TXTHR(x) ((x) << 8) /* Tx FIFO threshold */ +#define ESPI_MODE_RXTHR(x) ((x) << 0) /* Rx FIFO threshold */ + +#define ESPI_COM_CS(x) ((x) << 30) +#define ESPI_COM_TRANLEN(x) ((x) << 0) + +#define ESPI_CSMODE_CI_INACTIVEHIGH (1 << 31) +#define ESPI_CSMODE_CP_BEGIN_EDGCLK (1 << 30) +#define ESPI_CSMODE_REV_MSB_FIRST (1 << 29) +#define ESPI_CSMODE_DIV16 (1 << 28) +#define ESPI_CSMODE_PM(x) ((x) << 24) +#define ESPI_CSMODE_POL_ASSERTED_LOW (1 << 20) +#define ESPI_CSMODE_LEN(x) ((x) << 16) +#define ESPI_CSMODE_CSBEF(x) ((x) << 12) +#define ESPI_CSMODE_CSAFT(x) ((x) << 8) +#define ESPI_CSMODE_CSCG(x) ((x) << 3) + +#define ESPI_CSMODE_INIT_VAL (ESPI_CSMODE_POL_ASSERTED_LOW | \ + ESPI_CSMODE_CSBEF(0) | ESPI_CSMODE_CSAFT(0) | \ + ESPI_CSMODE_CSCG(1)) + + +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, + unsigned int max_hz, unsigned int mode) +{ + volatile ccsr_espi_t *espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR); + struct spi_slave *slave; + sys_info_t sysinfo; + unsigned long spibrg = 0; + unsigned char pm = 0; + int i; + + if (!spi_cs_is_valid(bus, cs)) + return NULL; + + slave = malloc(sizeof(struct spi_slave)); + if (!slave) + return NULL; + + slave->bus = bus; + slave->cs = cs; + + /* Enable eSPI interface */ + espi->mode = ESPI_MODE_RXTHR(3) | ESPI_MODE_TXTHR(4) | ESPI_MODE_EN; + + espi->event = 0xffffffff; /* Clear all eSPI events */ + espi->mask = 0x00000000; /* Mask all eSPI interrupts */ + + /* Init CS mode interface */ + for (i = 0; i < ESPI_MAX_CS_NUM; i++) + espi->csmode[i] = ESPI_CSMODE_INIT_VAL; + + espi->csmode[cs] &= ~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16 + | ESPI_CSMODE_CI_INACTIVEHIGH | ESPI_CSMODE_CP_BEGIN_EDGCLK + | ESPI_CSMODE_REV_MSB_FIRST | ESPI_CSMODE_LEN(0xF)); + + /* Set eSPI BRG clock source */ + get_sys_info(&sysinfo); + spibrg = sysinfo.freqSystemBus / 2; + if ((spibrg / max_hz) > 32) { + espi->csmode[cs] |= ESPI_CSMODE_DIV16; + pm = spibrg / (max_hz * 16 * 2); + if (pm > 16) { + pm = 16; + debug("Requested speed is too low: %d Hz" + " %d Hz is used.\n", max_hz, spibrg / (32 * 16)); + } + } else + pm = spibrg / (max_hz * 2); + if (pm) + pm--; + espi->csmode[cs] |= ESPI_CSMODE_PM(pm); + + /* Set eSPI mode */ + if (mode & SPI_CPHA) + espi->csmode[cs] |= ESPI_CSMODE_CP_BEGIN_EDGCLK; + if (mode & SPI_CPOL) + espi->csmode[cs] |= ESPI_CSMODE_CI_INACTIVEHIGH; + + /* Character bit order: msb first */ + espi->csmode[cs] |= ESPI_CSMODE_REV_MSB_FIRST; + + /* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits */ + espi->csmode[cs] |= ESPI_CSMODE_LEN(7); + + return slave; +} + +void spi_free_slave(struct spi_slave *slave) +{ + free(slave); +} + +void spi_init(void) +{ + +} + +int spi_claim_bus(struct spi_slave *slave) +{ + return 0; +} + +void spi_release_bus(struct spi_slave *slave) +{ + +} + +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, + void *din, unsigned long flags) +{ + volatile ccsr_espi_t *espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR); + unsigned int tmpdout, tmpdin, event; + unsigned int len = bitlen / 8 + ( bitlen % 4 ? 1 : 0 ); + int numBlks = bitlen / 32 + (bitlen % 32 ? 1 : 0); + unsigned char charsize = 32; + + debug("spi_xfer: slave %u:%u dout %08X(%08x) din %08X(%08x) len %u\n", + slave->bus, slave->cs, *(uint *) dout, dout, *(uint *) din, din, len); + + if (flags & SPI_XFER_BEGIN) + { + unsigned int com = 0; + com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF)); + com |= ESPI_COM_CS(espi_cs_state.cs); + com |= ESPI_COM_TRANLEN(len - 1); + espi->com = com; + } + + /* Clear all eSPI events */ + espi->event = 0xffffffff; + + /* handle data in 32-bit chunks */ + while (numBlks--) { + charsize = (bitlen >= 32 ? 32 : bitlen); + + event = espi->event; + if (event & ESPI_EV_TNF) { + tmpdout = *(u32 *)dout; + + /* Set up the next iteration if sending > 4 bytes */ + if (len > 4) { + len -= 4; + dout += 4; + } + + espi->tx = tmpdout; + espi->event |= ESPI_EV_TNF; + } + debug("*** spi_xfer: ... %08x written\n", tmpdout); + + /* Wait for eSPI transmit to get out */ + udelay(80); + + event = espi->event; + if (event & ESPI_EV_RNE) { + tmpdin = espi->rx; + *(u32 *) din = tmpdin; + + if (charsize == 32) { + din += 4; + } + + espi->event |= ESPI_EV_RNE; + } + debug("*** spi_xfer: ... %08x readed\n", tmpdin); + } + + if (flags & SPI_XFER_END) { + + /* clear the RXCNT and TXCNT */ + espi->mode &= ~ESPI_MODE_EN; + espi->mode |= ESPI_MODE_EN; + } + + return 0; +} + +int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{ + return bus == 0 && cs < ESPI_MAX_CS_NUM; +} + +void spi_cs_activate(struct spi_slave *slave) +{ + +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + +} Index: a/u-boot/drivers/spi/Makefile =================================================================== --- a/u-boot/drivers/spi/Makefile +++ b/u-boot/drivers/spi/Makefile @@ -36,6 +36,7 @@ COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o +COBJS-$(CONFIG_FSL_ESPI) += fsl_espi.o COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
