David Jander wrote: > Signed-off-by: David Jander <da...@protonic.nl> > ---
Hi David, in addition to Wolfgang's comments: > +static u32 system_rev; > +struct io_board_ctrl *mx51_io_board; Structure is not used, and probably does not match your board. You should drop it. > +#define POUT_HS (PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST) > +#define POUT_MS (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST) > +#define POUT_LS (PAD_CTL_DRV_MEDIUM) > +#define PIN_HYS (PAD_CTL_HYS_ENABLE) > +#define PIN_HYS_PULL (PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE | > PAD_CTL_PUE_PULL) > +#define PIN_HYS_KEEP (PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE) > +#define PIO_OD (PIN_HYS_PULL | PAD_CTL_22K_PU | > PAD_CTL_ODE_OPENDRAIN_ENABLE | PAD_CTL_DRV_MEDIUM) Consider to put these defines in include/asm/arch-mx51/iomux.h. They could be usefult for other boards, too. > + /* Raise the core frequency to 800MHz */ > + /* printf("Core at 400 MHz!\n"); */ > + /* writel(0x1, &mxc_ccm->cacrr); */ > + writel(0x0, &mxc_ccm->cacrr); Comment is misleading. Remove what is not needed. > + /* Setup other io's */ > + for(t=0; other_io_conf[t].pin>=0; t++) { Add spaces when needed. > +#ifdef BOARD_LATE_INIT Probably it is better (and in mx51evk, too) to remove the #ifdef, because we need to initialize the pmic, else some functionalities cannot work. It is mandatory that power_init is called. > diff --git a/board/Protonic/prtlvt2/prtlvt2.h > b/board/Protonic/prtlvt2/prtlvt2.h > +#ifndef __BOARD_FREESCALE_MX51_EVK_H__ > +#define __BOARD_FREESCALE_MX51_EVK_H__ > + > +#ifndef __ASSEMBLY__ > +struct io_board_ctrl { > + u16 led_ctrl; /* 0x00 */ > + u16 resv1[0x03]; > + u16 sb_stat; /* 0x08 */ > + u16 resv2[0x03]; > + u16 int_stat; /* 0x10 */ > + u16 resv3[0x07]; > + u16 int_rest; /* 0x20 */ > + u16 resv4[0x0B]; > + u16 int_mask; /* 0x38 */ > + u16 resv5[0x03]; > + u16 id1; /* 0x40 */ > + u16 resv6[0x03]; > + u16 id2; /* 0x48 */ > + u16 resv7[0x03]; > + u16 version; /* 0x50 */ > + u16 resv8[0x03]; > + u16 id3; /* 0x58 */ > + u16 resv9[0x03]; > + u16 sw_reset; /* 0x60 */ > +}; > +#endif Is this structure really used ? I have not seen in code. Or does it come only from mx51evk ? You can remove the whole file, if it is not needed. Best regards, Stefano Babic -- ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: off...@denx.de ===================================================================== _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot